JAJSCD2E august   2016  – march 2023 TUSB546-DCI

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Supply Characteristics
    6. 6.6  DC Electrical Characteristics
    7. 6.7  AC Electrical Characteristics
    8. 6.8  Timing Requirements
    9. 6.9  Switching Characteristics
    10. 6.10 Typical Characteristics
      1.      Parameter Measurement Information
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 USB 3.1
      2. 7.3.2 DisplayPort
      3. 7.3.3 4-Level Inputs
      4. 7.3.4 Receiver Linear Equalization
    4. 7.4 Device Functional Modes
      1. 7.4.1 Device Configuration in GPIO Mode
      2. 7.4.2 28
      3. 7.4.3 Device Configuration In I2C Mode
      4. 7.4.4 DisplayPort Mode
      5. 7.4.5 Linear EQ Configuration
      6. 7.4.6 USB3.1 Modes
      7. 7.4.7 Operation Timing – Power Up
    5. 7.5 Programming
    6. 7.6 Register Maps
      1. 7.6.1 General Register (address = 0x0A) [reset = 00000001]
      2. 7.6.2 DisplayPort Control/Status Registers (address = 0x10) [reset = 00000000]
      3. 7.6.3 DisplayPort Control/Status Registers (address = 0x11) [reset = 00000000]
      4. 7.6.4 DisplayPort Control/Status Registers (address = 0x12) [reset = 00000000]
      5. 7.6.5 DisplayPort Control/Status Registers (address = 0x13) [reset = 00000000]
      6. 7.6.6 USB3.1 Control/Status Registers (address = 0x20) [reset = 00000000]
      7. 7.6.7 USB3.1 Control/Status Registers (address = 0x21) [reset = 00000000]
      8. 7.6.8 USB3.1 Control/Status Registers (address = 0x22) [reset = 00000100]
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
    3. 8.3 System Examples
      1. 8.3.1 USB 3.1 Only
      2. 8.3.2 USB 3.1 and 2 Lanes of DisplayPort
      3. 8.3.3 DisplayPort Only
    4. 8.4 Power Supply Recommendations
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  9. 9 Device and Documentation Support
    1. 9.1 ドキュメントの更新通知を受け取る方法
    2. 9.2 サポート・リソース
    3. 9.3 Trademarks
    4. 9.4 静電気放電に関する注意事項
    5. 9.5 用語集
  10. 10Mechanical, Packaging, and Orderable Information

4 Revision History

Changes from Revision D (May 2019) to Revision E (March 2023)

  • 文書全体にわたって表、図、相互参照の採番方法を更新Go
  • データシート全体にわたって包括的な用語を追加Go
  • MSL レベルを2 から1 へ更新Go

Changes from Revision C (April 2018) to Revision D (May 2019)

  • Added following to pin 11 description: If I2C_EN = “F”, then this pin must be set to “F” or “0”. Go

Changes from Revision B (June 2017) to Revision C (April 2018)

  • Changed the appearance of the pinout image in the Pin Configuration and Function sectionGo
  • Added Note 1 to the Pin Functions tableGo
  • Changed the USB3.1 Control/Status Registers reset value From: 00000000 To: 00000100Go
  • Changed the Reset value of bit 3:2 From: 00 To: 01 in Table 7-18 Go

Changes from Revision A (April 2017) to Revision B (June 2017)

  • Changed the Human-body model (HBM) value From: ±6000 V To: ±5000 in the ESD Ratings Go

Changes from Revision * (August 2016) to Revision A (April 2017)

  • Changed title of Figure 6-2 From: USB TX EQ Settings Curves To: USB RX EQ Settings CurvesGo
  • Changed title of Figure 6-3 From: USB RX EQ Settings Curves To: USB TX EQ Settings CurvesGo