JAJSD07C September   2016  – December 2022 DS90UB934-Q1

PRODUCTION DATA  

  1.   特長
  2. 1アプリケーション
  3. 2概要
  4. 3Revision History
  5.   Pin Configuration and Functions
  6. 4Specifications
    1. 4.1 Absolute Maximum Ratings
    2. 4.2 ESD Ratings
    3. 4.3 Recommended Operating Conditions
    4. 4.4 Thermal Information
    5. 4.5 DC Electrical Characteristics
    6. 4.6 AC Electrical Characteristics
    7. 4.7 Recommended Timing for the Serial Control Bus
    8. 4.8 Typical Characteristics
  7. 5Detailed Description
    1. 5.1 Overview
      1. 5.1.1 Functional Description
    2. 5.2 Functional Block Diagram
    3. 5.3 Feature Description
      1. 5.3.1 Serial Frame Format
      2. 5.3.2 Line Rate Calculations for the DS90UB933/934
      3. 5.3.3 Deserializer Multiplexer Input
    4. 5.4 Device Functional Modes
      1. 5.4.1 RX MODE Pin
      2. 5.4.2 DVP Output Control
        1. 5.4.2.1 LOCK Status
      3. 5.4.3 Input Jitter Tolerance
      4. 5.4.4 Adaptive Equalizer
      5. 5.4.5 Channel Monitor Loop-Through Output Driver
        1. 5.4.5.1 Code Example for CMLOUT FPD3 RX Port 0:
      6. 5.4.6 GPIO Support
        1. 5.4.6.1 Back Channel GPIO
        2. 5.4.6.2 GPIO Pin Status
        3. 5.4.6.3 Other GPIO Pin Controls
        4. 5.4.6.4 FrameSync Operation
          1. 5.4.6.4.1 External FrameSync Control
          2. 5.4.6.4.2 Internally Generated FrameSync
            1. 5.4.6.4.2.1 Code Example for Internally Generated FrameSync
    5. 5.5 Programming
      1. 5.5.1 Serial Control Bus
        1. 5.5.1.1 I2C Target Operation
        2. 5.5.1.2 Remote Target Operation
        3. 5.5.1.3 Remote I2C Targets Data Throughput
        4. 5.5.1.4 Remote Target Addressing
        5. 5.5.1.5 Broadcast Write to Remote Target Devices
        6. 5.5.1.6 Code Example for Broadcast Write
      2. 5.5.2 Interrupt Support
        1. 5.5.2.1 Code Example to Enable Interrupts
        2. 5.5.2.2 FPD-Link III Receive Port Interrupts
        3. 5.5.2.3 Code Example to Readback Interrupts
        4. 5.5.2.4 Built-In Self Test (BIST)
          1. 5.5.2.4.1 BIST Configuration and Status
    6. 5.6 Register Maps
      1. 5.6.1 Register Description
      2. 5.6.2 Registers
      3. 5.6.3 Indirect Access Registers
      4. 5.6.4 Indirect Access Register Map
        1. 5.6.4.1 FPD3 Channel 0 Registers
        2. 5.6.4.2 FPD3 Channel 1 Registers
        3. 5.6.4.3 FPD3 RX Shared Registers
  8. 6Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Power Over Coax
    3. 6.3 Typical Application
      1. 6.3.1 Design Requirements
      2. 6.3.2 Detailed Design Procedure
      3. 6.3.3 Application Curves
    4. 6.4 System Examples
    5. 6.5 Power Supply Recommendations
      1. 6.5.1 VDD Power Supply
      2. 6.5.2 Power-Up Sequencing
      3. 6.5.3 PDB Pin
      4. 6.5.4 Ground
    6. 6.6 Layout
      1. 6.6.1 Layout Guidelines
        1. 6.6.1.1 DVP Interface Guidelines
      2. 6.6.2 Layout Example
  9.   Mechanical, Packaging, and Orderable Information
  10. 7Device and Documentation Support
    1. 7.1 Documentation Support
      1. 7.1.1 Related Documentation
    2. 7.2 Glossary
    3. 7.3 Receiving Notification of Documentation Updates
    4. 7.4 サポート・リソース
    5. 7.5 Trademarks
  11.   Mechanical, Packaging, and Orderable Information

5.6.4.2 FPD3 Channel 1 Registers

Table 5-13 FPD3 Channel 1 Registers
Page Addr (hex) Register Name Bit(s) Field Type Default Description
2 0x00 RESERVED 7:0 RESERVED R/W 0x0 Reserved
2 0x01 RESERVED 7:0 RESERVED R/W 0xE0 Reserved
2 0x02 RESERVED 7:0 RESERVED R/W 0x0 Reserved
2 0x03 RESERVED 7:0 RESERVED R/W 0x20 Reserved
2 0x04 RESERVED 7:0 RESERVED R/W 0x3F Reserved
2 0x05 RESERVED 7:0 RESERVED R/W 0x0 Reserved
2 0x06 RESERVED 7:0 RESERVED R/W 0x74 Reserved
2 0x07 RESERVED 7:0 RESERVED R/W 0x0A Reserved
2 0x08-0x0E RESERVED 7:0 RESERVED R/W 0x0 Reserved
2 0x0F ATP_CTL1 7:1 RESERVED R/W 0x0 Reserved
0 EN_LOOP_DRV R/W 0x0 Enable FPD3 data to loop through driver
0: disabled (default)
1: enabled
2 0x10 ATP_CTL2 7:2 RESERVED R/W 0x0 Reserved
1 EN_DATA_OUT R/W 0x0 Enable CMLOUT data output
0: disabled (default)
1: enabled
0 RESERVED R/W 0x0 Reserved
2 0x11-0x12 RESERVED 7:0 RESERVED R/W 0x0 Reserved
2 0x13 RESERVED 7:0 RESERVED R/W 0x20 Reserved
2 0x14 RESERVED 7:0 RESERVED R/W 0x3F Reserved