JAJSES4A February   2018  – April 2020 ADC08DJ3200

PRODUCTION DATA.  

  1. 1 特長
    1.     ADC08DJ3200 の測定された入力帯域幅
  2. 2 アプリケーション
  3. 3 概要
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics: DC Specifications
    6. 7.6  Electrical Characteristics: Power Consumption
    7. 7.7  Electrical Characteristics: AC Specifications (Dual-Channel Mode)
    8. 7.8  Electrical Characteristics: AC Specifications (Single-Channel Mode)
    9. 7.9  Timing Requirements
    10. 7.10 Switching Characteristics
    11. 7.11 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Device Comparison
      2. 8.3.2 Analog Inputs
        1. 8.3.2.1 Analog Input Protection
        2. 8.3.2.2 Full-Scale Voltage (VFS) Adjustment
        3. 8.3.2.3 Analog Input Offset Adjust
      3. 8.3.3 ADC Core
        1. 8.3.3.1 ADC Theory of Operation
        2. 8.3.3.2 ADC Core Calibration
        3. 8.3.3.3 Analog Reference Voltage
        4. 8.3.3.4 ADC Overrange Detection
        5. 8.3.3.5 Code Error Rate (CER)
      4. 8.3.4 Temperature Monitoring Diode
      5. 8.3.5 Timestamp
      6. 8.3.6 Clocking
        1. 8.3.6.1 Noiseless Aperture Delay Adjustment (tAD Adjust)
        2. 8.3.6.2 Aperture Delay Ramp Control (TAD_RAMP)
        3. 8.3.6.3 SYSREF Capture for Multi-Device Synchronization and Deterministic Latency
          1. 8.3.6.3.1 SYSREF Position Detector and Sampling Position Selection (SYSREF Windowing)
          2. 8.3.6.3.2 Automatic SYSREF Calibration
      7. 8.3.7 JESD204B Interface
        1. 8.3.7.1 Transport Layer
        2. 8.3.7.2 Scrambler
        3. 8.3.7.3 Link Layer
          1. 8.3.7.3.1 Code Group Synchronization (CGS)
          2. 8.3.7.3.2 Initial Lane Alignment Sequence (ILAS)
          3. 8.3.7.3.3 8b, 10b Encoding
          4. 8.3.7.3.4 Frame and Multiframe Monitoring
        4. 8.3.7.4 Physical Layer
          1. 8.3.7.4.1 SerDes Pre-Emphasis
        5. 8.3.7.5 JESD204B Enable
        6. 8.3.7.6 Multi-Device Synchronization and Deterministic Latency
        7. 8.3.7.7 Operation in Subclass 0 Systems
      8. 8.3.8 Alarm Monitoring
        1. 8.3.8.1 Clock Upset Detection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Dual-Channel Mode
      2. 8.4.2 Single-Channel Mode (DES Mode)
      3. 8.4.3 JESD204B Modes
        1. 8.4.3.1 JESD204B Output Data Formats
      4. 8.4.4 Power-Down Modes
      5. 8.4.5 Test Modes
        1. 8.4.5.1 Serializer Test-Mode Details
        2. 8.4.5.2 PRBS Test Modes
        3. 8.4.5.3 Ramp Test Mode
        4. 8.4.5.4 Short and Long Transport Test Mode
          1. 8.4.5.4.1 Short Transport Test Pattern
        5. 8.4.5.5 D21.5 Test Mode
        6. 8.4.5.6 K28.5 Test Mode
        7. 8.4.5.7 Repeated ILA Test Mode
        8. 8.4.5.8 Modified RPAT Test Mode
      6. 8.4.6 Calibration Modes and Trimming
        1. 8.4.6.1 Foreground Calibration Mode
        2. 8.4.6.2 Background Calibration Mode
        3. 8.4.6.3 Low-Power Background Calibration (LPBG) Mode
      7. 8.4.7 Offset Calibration
      8. 8.4.8 Trimming
      9. 8.4.9 Offset Filtering
    5. 8.5 Programming
      1. 8.5.1 Using the Serial Interface
        1. 8.5.1.1 SCS
        2. 8.5.1.2 SCLK
        3. 8.5.1.3 SDI
        4. 8.5.1.4 SDO
        5. 8.5.1.5 Streaming Mode
    6. 8.6 Register Maps
      1. 8.6.1 Memory Map
      2. 8.6.2 Register Descriptions
        1. 8.6.2.1  Standard SPI-3.0 (0x000 to 0x00F)
          1. Table 23. Standard SPI-3.0 Registers
          2. 8.6.2.1.1 Configuration A Register (address = 0x000) [reset = 0x30]
            1. Table 24. CONFIG_A Field Descriptions
          3. 8.6.2.1.2 Device Configuration Register (address = 0x002) [reset = 0x00]
            1. Table 25. DEVICE_CONFIG Field Descriptions
          4. 8.6.2.1.3 Chip Type Register (address = 0x003) [reset = 0x03]
            1. Table 26. CHIP_TYPE Field Descriptions
          5. 8.6.2.1.4 Chip ID Register (address = 0x004 to 0x005) [reset = 0x0020]
            1. Table 27. CHIP_ID Field Descriptions
          6. 8.6.2.1.5 Chip Version Register (address = 0x006) [reset = 0x01]
            1. Table 28. CHIP_VERSION Field Descriptions
          7. 8.6.2.1.6 Vendor Identification Register (address = 0x00C to 0x00D) [reset = 0x0451]
            1. Table 29. VENDOR_ID Field Descriptions
        2. 8.6.2.2  User SPI Configuration (0x010 to 0x01F)
          1. 8.6.2.2.1 User SPI Configuration Register (address = 0x010) [reset = 0x00]
            1. Table 31. USR0 Field Descriptions
        3. 8.6.2.3  Miscellaneous Analog Registers (0x020 to 0x047)
          1. 8.6.2.3.1 Clock Control Register 0 (address = 0x029) [reset = 0x00]
            1. Table 33. CLK_CTRL0 Field Descriptions
          2. 8.6.2.3.2 Clock Control Register 1 (address = 0x02A) [reset = 0x00]
            1. Table 34. CLK_CTRL1 Field Descriptions
          3. 8.6.2.3.3 SYSREF Capture Position Register (address = 0x02C-0x02E) [reset = Undefined]
            1. Table 35. SYSREF_POS Field Descriptions
          4. 8.6.2.3.4 INA Full-Scale Range Adjust Register (address = 0x030-0x031) [reset = 0xA000]
            1. Table 36. FS_RANGE_A Field Descriptions
          5. 8.6.2.3.5 INB Full-Scale Range Adjust Register (address = 0x032-0x033) [reset = 0xA000]
            1. Table 37. FS_RANGE_B Field Descriptions
          6. 8.6.2.3.6 Internal Reference Bypass Register (address = 0x038) [reset = 0x00]
            1. Table 38. BG_BYPASS Field Descriptions
          7. 8.6.2.3.7 TMSTP± Control Register (address = 0x03B) [reset = 0x00]
            1. Table 39. TMSTP_CTRL Field Descriptions
        4. 8.6.2.4  Serializer Registers (0x048 to 0x05F)
          1. 8.6.2.4.1 Serializer Pre-Emphasis Control Register (address = 0x048) [reset = 0x00]
            1. Table 41. SER_PE Field Descriptions
        5. 8.6.2.5  Calibration Registers (0x060 to 0x0FF)
          1. 8.6.2.5.1  Input Mux Control Register (address = 0x060) [reset = 0x01]
            1. Table 43. INPUT_MUX Field Descriptions
          2. 8.6.2.5.2  Calibration Enable Register (address = 0x061) [reset = 0x01]
            1. Table 44. CAL_EN Field Descriptions
          3. 8.6.2.5.3  Calibration Configuration 0 Register (address = 0x062) [reset = 0x01]
            1. Table 45. CAL_CFG0 Field Descriptions
          4. 8.6.2.5.4  Calibration Status Register (address = 0x06A) [reset = Undefined]
            1. Table 46. CAL_STATUS Field Descriptions
          5. 8.6.2.5.5  Calibration Pin Configuration Register (address = 0x06B) [reset = 0x00]
            1. Table 47. CAL_PIN_CFG Field Descriptions
          6. 8.6.2.5.6  Calibration Software Trigger Register (address = 0x06C) [reset = 0x01]
            1. Table 48. CAL_SOFT_TRIG Field Descriptions
          7. 8.6.2.5.7  Low-Power Background Calibration Register (address = 0x06E) [reset = 0x88]
            1. Table 49. CAL_LP Field Descriptions
          8. 8.6.2.5.8  Calibration Data Enable Register (address = 0x070) [reset = 0x00]
            1. Table 50. CAL_DATA_EN Field Descriptions
          9. 8.6.2.5.9  Calibration Data Register (address = 0x071) [reset = Undefined]
            1. Table 51. CAL_DATA Field Descriptions
          10. 8.6.2.5.10 Channel A Gain Trim Register (address = 0x07A) [reset = Undefined]
            1. Table 52. GAIN_TRIM_A Field Descriptions
          11. 8.6.2.5.11 Channel B Gain Trim Register (address = 0x07B) [reset = Undefined]
            1. Table 53. GAIN_TRIM_B Field Descriptions
          12. 8.6.2.5.12 Band-Gap Reference Trim Register (address = 0x07C) [reset = Undefined]
            1. Table 54. BG_TRIM Field Descriptions
          13. 8.6.2.5.13 VINA Input Resistor Trim Register (address = 0x07E) [reset = Undefined]
            1. Table 55. RTRIM_A Field Descriptions
          14. 8.6.2.5.14 VINB Input Resistor Trim Register (address = 0x07F) [reset = Undefined]
            1. Table 56. RTRIM_B Field Descriptions
          15. 8.6.2.5.15 Timing Adjust for A-ADC, Single-Channel Mode, Foreground Calibration Register (address = 0x080) [reset = Undefined]
            1. Table 57. TADJ_A_FG90 Field Descriptions
          16. 8.6.2.5.16 Timing Adjust for B-ADC, Single-Channel Mode, Foreground Calibration Register (address = 0x081) [reset = Undefined]
            1. Table 58. TADJ_B_FG0 Field Descriptions
          17. 8.6.2.5.17 Timing Adjust for A-ADC, Single-Channel Mode, Background Calibration Register (address = 0x082) [reset = Undefined]
            1. Table 59. TADJ_B_FG0 Field Descriptions
          18. 8.6.2.5.18 Timing Adjust for C-ADC, Single-Channel Mode, Background Calibration Register (address = 0x083) [reset = Undefined]
            1. Table 60. TADJ_B_FG0 Field Descriptions
          19. 8.6.2.5.19 Timing Adjust for C-ADC, Single-Channel Mode, Background Calibration Register (address = 0x084) [reset = Undefined]
            1. Table 61. TADJ_B_FG0 Field Descriptions
          20. 8.6.2.5.20 Timing Adjust for B-ADC, Single-Channel Mode, Background Calibration Register (address = 0x085) [reset = Undefined]
            1. Table 62. TADJ_B_FG0 Field Descriptions
          21. 8.6.2.5.21 Timing Adjust for A-ADC, Dual-Channel Mode Register (address = 0x086) [reset = Undefined]
            1. Table 63. TADJ_A Field Descriptions
          22. 8.6.2.5.22 Timing Adjust for C-ADC Acting for A-ADC, Dual-Channel Mode Register (address = 0x087) [reset = Undefined]
            1. Table 64. TADJ_CA Field Descriptions
          23. 8.6.2.5.23 Timing Adjust for C-ADC Acting for B-ADC, Dual-Channel Mode Register (address = 0x088) [reset = Undefined]
            1. Table 65. TADJ_CB Field Descriptions
          24. 8.6.2.5.24 Timing Adjust for B-ADC, Dual-Channel Mode Register (address = 0x089) [reset = Undefined]
            1. Table 66. TADJ_B Field Descriptions
          25. 8.6.2.5.25 Offset Adjustment for A-ADC and INA Register (address = 0x08A-0x08B) [reset = Undefined]
            1. Table 67. OADJ_A_INA Field Descriptions
          26. 8.6.2.5.26 Offset Adjustment for A-ADC and INB Register (address = 0x08C-0x08D) [reset = Undefined]
            1. Table 68. OADJ_A_INB Field Descriptions
          27. 8.6.2.5.27 Offset Adjustment for C-ADC and INA Register (address = 0x08E-0x08F) [reset = Undefined]
            1. Table 69. OADJ_C_INA Field Descriptions
          28. 8.6.2.5.28 Offset Adjustment for C-ADC and INB Register (address = 0x090-0x091) [reset = Undefined]
            1. Table 70. OADJ_C_INB Field Descriptions
          29. 8.6.2.5.29 Offset Adjustment for B-ADC and INA Register (address = 0x092-0x093) [reset = Undefined]
            1. Table 71. OADJ_B_INA Field Descriptions
          30. 8.6.2.5.30 Offset Adjustment for B-ADC and INB Register (address = 0x094-0x095) [reset = Undefined]
            1. Table 72. OADJ_B_INB Field Descriptions
          31. 8.6.2.5.31 Offset Filtering Control 0 Register (address = 0x097) [reset = 0x00]
            1. Table 73. OSFILT0 Field Descriptions
          32. 8.6.2.5.32 Offset Filtering Control 1 Register (address = 0x098) [reset = 0x33]
            1. Table 74. OSFILT1 Field Descriptions
        6. 8.6.2.6  ADC Bank Registers (0x100 to 0x15F)
          1. 8.6.2.6.1  Timing Adjustment for Bank 0 (0° Clock) Register (address = 0x102) [reset = Undefined]
            1. Table 76. B0_TIME_0 Field Descriptions
          2. 8.6.2.6.2  Timing Adjustment for Bank 0 (–90° Clock) Register (address = 0x103) [reset = Undefined]
            1. Table 77. B0_TIME_90 Field Descriptions
          3. 8.6.2.6.3  Timing Adjustment for Bank 1 (0° Clock) Register (address = 0x112) [reset = Undefined]
            1. Table 78. B1_TIME_0 Field Descriptions
          4. 8.6.2.6.4  Timing Adjustment for Bank 1 (–90° Clock) Register (address = 0x113) [reset = Undefined]
            1. Table 79. B1_TIME_90 Field Descriptions
          5. 8.6.2.6.5  Timing Adjustment for Bank 2 (0° Clock) Register (address = 0x122) [reset = Undefined]
            1. Table 80. B2_TIME_0 Field Descriptions
          6. 8.6.2.6.6  Timing Adjustment for Bank 2 (–90° Clock) Register (address = 0x123) [reset = Undefined]
            1. Table 81. B2_TIME_90 Field Descriptions
          7. 8.6.2.6.7  Timing Adjustment for Bank 3 (0° Clock) Register (address = 0x132) [reset = Undefined]
            1. Table 82. B3_TIME_0 Field Descriptions
          8. 8.6.2.6.8  Timing Adjustment for Bank 3 (–90° Clock) Register (address = 0x133) [reset = Undefined]
            1. Table 83. B3_TIME_90 Field Descriptions
          9. 8.6.2.6.9  Timing Adjustment for Bank 4 (0° Clock) Register (address = 0x142) [reset = Undefined]
            1. Table 84. B4_TIME_0 Field Descriptions
          10. 8.6.2.6.10 Timing Adjustment for Bank 4 (–90° Clock) Register (address = 0x143) [reset = Undefined]
            1. Table 85. B4_TIME_90 Field Descriptions
          11. 8.6.2.6.11 Timing Adjustment for Bank 5 (0° Clock) Register (address = 0x152) [reset = Undefined]
            1. Table 86. B5_TIME_0 Field Descriptions
          12. 8.6.2.6.12 Timing Adjustment for Bank 5 (–90° Clock) Register (address = 0x153) [reset = Undefined]
            1. Table 87. B5_TIME_90 Field Descriptions
        7. 8.6.2.7  LSB Control Registers (0x160 to 0x1FF)
          1. 8.6.2.7.1 LSB Control Bit Output Register (address = 0x160) [reset = 0x00]
            1. Table 89. ENC_LSB Field Descriptions
        8. 8.6.2.8  JESD204B Registers (0x200 to 0x20F)
          1. 8.6.2.8.1  JESD204B Enable Register (address = 0x200) [reset = 0x01]
            1. Table 91. JESD_EN Field Descriptions
          2. 8.6.2.8.2  JESD204B Mode Register (address = 0x201) [reset = 0x02]
            1. Table 92. JMODE Field Descriptions
          3. 8.6.2.8.3  JESD204B K Parameter Register (address = 0x202) [reset = 0x1F]
            1. Table 93. KM1 Field Descriptions
          4. 8.6.2.8.4  JESD204B Manual SYNC Request Register (address = 0x203) [reset = 0x01]
            1. Table 94. JSYNC_N Field Descriptions
          5. 8.6.2.8.5  JESD204B Control Register (address = 0x204) [reset = 0x02]
            1. Table 95. JCTRL Field Descriptions
          6. 8.6.2.8.6  JESD204B Test Pattern Control Register (address = 0x205) [reset = 0x00]
            1. Table 96. JTEST Field Descriptions
          7. 8.6.2.8.7  JESD204B DID Parameter Register (address = 0x206) [reset = 0x00]
            1. Table 97. DID Field Descriptions
          8. 8.6.2.8.8  JESD204B Frame Character Register (address = 0x207) [reset = 0x00]
            1. Table 98. FCHAR Field Descriptions
          9. 8.6.2.8.9  JESD204B, System Status Register (address = 0x208) [reset = Undefined]
            1. Table 99. JESD_STATUS Field Descriptions
          10. 8.6.2.8.10 JESD204B Channel Power-Down Register (address = 0x209) [reset = 0x00]
            1. Table 100. PD_CH Field Descriptions
          11. 8.6.2.8.11 JESD204B Extra Lane Enable (Link A) Register (address = 0x20A) [reset = 0x00]
            1. Table 101. JESD204B Extra Lane Enable (Link A) Field Descriptions
          12. 8.6.2.8.12 JESD204B Extra Lane Enable (Link B) Register (address = 0x20B) [reset = 0x00]
            1. Table 102. JESD204B Extra Lane Enable (Link B) Field Descriptions
        9. 8.6.2.9  Digital Down Converter Registers (0x210-0x2AF)
          1. 8.6.2.9.1 Overrange Threshold 0 Register (address = 0x211) [reset = 0xF2]
            1. Table 104. OVR_T0 Field Descriptions
          2. 8.6.2.9.2 Overrange Threshold 1 Register (address = 0x212) [reset = 0xAB]
            1. Table 105. OVR_T1 Field Descriptions
          3. 8.6.2.9.3 Overrange Configuration Register (address = 0x213) [reset = 0x07]
            1. Table 106. OVR_CFG Field Descriptions
        10. 8.6.2.10 Spin Identification Register (address = 0x297) [reset = Undefined]
          1. Table 107. SPIN_ID Field Descriptions
      3. 8.6.3 SYSREF Calibration Registers (0x2B0 to 0x2BF)
        1. 8.6.3.1 SYSREF Calibration Enable Register (address = 0x2B0) [reset = 0x00]
          1. Table 109. SRC_EN Field Descriptions
        2. 8.6.3.2 SYSREF Calibration Configuration Register (address = 0x2B1) [reset = 0x05]
          1. Table 110. SRC_CFG Field Descriptions
        3. 8.6.3.3 SYSREF Calibration Status Register (address = 0x2B2 to 0x2B4) [reset = Undefined]
          1. Table 111. SRC_STATUS Field Descriptions
        4. 8.6.3.4 DEVCLK Aperture Delay Adjustment Register (address = 0x2B5 to 0x2B7) [reset = 0x000000]
          1. Table 112. TAD Field Descriptions
        5. 8.6.3.5 DEVCLK Timing Adjust Ramp Control Register (address = 0x2B8) [reset = 0x00]
          1. Table 113. TAD_RAMP Field Descriptions
      4. 8.6.4 Alarm Registers (0x2C0 to 0x2C2)
        1. 8.6.4.1 Alarm Interrupt Register (address = 0x2C0) [reset = Undefined]
          1. Table 115. ALARM Field Descriptions
        2. 8.6.4.2 Alarm Status Register (address = 0x2C1) [reset = 0x1F]
          1. Table 116. ALM_STATUS Field Descriptions
        3. 8.6.4.3 Alarm Mask Register (address = 0x2C2) [reset = 0x1F]
          1. Table 117. ALM_MASK Field Descriptions
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Wideband RF Sampling Receiver
        1. 9.2.1.1 Design Requirements
          1. 9.2.1.1.1 Input Signal Path
          2. 9.2.1.1.2 Clocking
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Calculating Values of AC-Coupling Capacitors
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Reconfigurable Dual-Channel 2.5-GSPS or Single-Channel 5.0-Gsps Oscilloscope
        1. 9.2.2.1 Design Requirements
          1. 9.2.2.1.1 Input Signal Path
          2. 9.2.2.1.2 Clocking
          3. 9.2.2.1.3 ADC08DJ3200
        2. 9.2.2.2 Application Curves
    3. 9.3 Initialization Set Up
  10. 10Power Supply Recommendations
    1. 10.1 Power Sequencing
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 デベロッパー・ネットワークの製品に関する免責事項
      2. 12.1.2 開発サポート
    2. 12.2 ドキュメントのサポート
      1. 12.2.1 関連資料
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 サポート・リソース
    5. 12.5 商標
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 Glossary
  13. 13メカニカル、パッケージ、および注文情報

8.6.1 Memory Map

ADDRESS RESET ACRONYM TYPE REGISTER NAME
STANDARD SPI-3.0 (0x000 to 0x00F)
0x000 0x30 CONFIG_A R/W Configuration A Register
0x001 Undefined RESERVED R RESERVED
0x002 0x00 DEVICE_CONFIG R/W Device Configuration Register
0x003 0x03 CHIP_TYPE R Chip Type Register
0x004-0x005 0x0020 CHIP_ID R Chip ID Registers
0x006 0x0A CHIP_VERSION R Chip Version Register
0x007-0x00B Undefined RESERVED R RESERVED
0x00C-0x00D 0x0451 VENDOR_ID R Vendor Identification Register
0x00E-0x00F Undefined RESERVED R RESERVED
USER SPI CONFIGURATION (0x010 to 0x01F)
0x010 0x00 USR0 R/W User SPI Configuration Register
0x011-0x01F Undefined RESERVED R RESERVED
MISCELLANEOUS ANALOG REGISTERS (0x020 to 0x047)
0x020-0x028 Undefined RESERVED R RESERVED
0x029 0x00 CLK_CTRL0 R/W Clock Control Register 0
0x02A 0x20 CLK_CTRL1 R/W Clock Control Register 1
0x02B Undefined RESERVED R RESERVED
0x02C-0x02E Undefined SYSREF_POS R SYSREF Capture Position Register
0x02F Undefined RESERVED R RESERVED
0x030-0x031 0xA000 FS_RANGE_A R/W INA Full-Scale Range Adjust Register
0x032-0x033 0xA000 FS_RANGE_B R/W INB Full-Scale Range Adjust Register
0x034-0x037 Undefined RESERVED R RESERVED
0x038 0x00 BG_BYPASS R/W Internal Reference Bypass Register
0x039-0x03A Undefined RESERVED R RESERVED
0x03B 0x00 TMSTP_CTRL R/W TMSTP± Control Register
0x03C-0x047 Undefined RESERVED R RESERVED
SERIALIZER REGISTERS (0x048 to 0x05F)
0x048 0x00 SER_PE R/W Serializer Pre-Emphasis Control Register
0x049-0x05F Undefined RESERVED R RESERVED
CALIBRATION REGISTERS (0x060 to 0x0FF)
0x060 0x01 INPUT_MUX R/W Input Mux Control Register
0x061 0x01 CAL_EN R/W Calibration Enable Register
0x062 0x01 CAL_CFG0 R/W Calibration Configuration 0 Register
0x063-0x069 Undefined RESERVED R RESERVED
0x06A Undefined CAL_STATUS R Calibration Status Register
0x06B 0x00 CAL_PIN_CFG R/W Calibration Pin Configuration Register
0x06C 0x01 CAL_SOFT_TRIG R/W Calibration Software Trigger Register
0x06D Undefined RESERVED R RESERVED
0x06E 0x88 CAL_LP R/W Low-Power Background Calibration Register
0x06F Undefined RESERVED R RESERVED
0x070 0x00 CAL_DATA_EN R/W Calibration Data Enable Register
0x071 Undefined CAL_DATA R/W Calibration Data Register
0x072-0x079 Undefined RESERVED R RESERVED
0x07A Undefined GAIN_TRIM_A R/W Channel A Gain Trim Register
0x07B Undefined GAIN_TRIM_B R/W Channel B Gain Trim Register
0x07C Undefined BG_TRIM R/W Band-Gap Reference Trim Register
0x07D Undefined RESERVED R RESERVED
0x07E Undefined RTRIM_A R/W VINA Input Resistor Trim Register
0x07F Undefined RTRIM_B R/W VINB Input Resistor Trim Register
0x080 Undefined TADJ_A_FG90 R/W Timing Adjustment for A-ADC, Single-Channel Mode, Foreground Calibration Register
0x081 Undefined TADJ_B_FG0 R/W Timing Adjustment for B-ADC, Single-Channel Mode, Foreground Calibration Register
0x082 Undefined TADJ_A_BG90 R/W Timing Adjustment for A-ADC, Single-Channel Mode, Background Calibration Register
0x083 Undefined TADJ_C_BG0 R/W Timing Adjustment for C-ADC, Single-Channel Mode, Background Calibration Register
0x084 Undefined TADJ_C_BG90 R/W Timing Adjustment for C-ADC, Single-Channel Mode, Background Calibration Register
0x085 Undefined TADJ_B_BG0 R/W Timing Adjustment for B-ADC, Single-Channel Mode, Background Calibration Register
0x086 Undefined TADJ_A R/W Timing Adjustment for A-ADC, Dual-Channel Mode Register
0x087 Undefined TADJ_CA R/W Timing Adjustment for C-ADC Acting for A-ADC, Dual-Channel Mode Register
0x088 Undefined TADJ_CB R/W Timing Adjustment for C-ADC Acting for B-ADC, Dual-Channel Mode Register
0x089 Undefined TADJ_B R/W Timing Adjustment for B-ADC, Dual-Channel Mode Register
0x08A-0x08B Undefined OADJ_A_INA R/W Offset Adjustment for A-ADC and INA Register
0x08C-0x08D Undefined OADJ_A_INB R/W Offset Adjustment for A-ADC and INB Register
0x08E-0x08F Undefined OADJ_C_INA R/W Offset Adjustment for C-ADC and INA Register
0x090-0x091 Undefined OADJ_C_INB R/W Offset Adjustment for C-ADC and INB Register
0x092-0x093 Undefined OADJ_B_INA R/W Offset Adjustment for B-ADC and INA Register
0x094-0x095 Undefined OADJ_B_INB R/W Offset Adjustment for B-ADC and INB Register
0x096 Undefined RESERVED R RESERVED
0x097 0x00 OSFILT0 R/W Offset Filtering Control 0
0x098 0x33 OSFILT1 R/W Offset Filtering Control 1
0x099-0x0FF Undefined RESERVED R RESERVED
ADC BANK REGISTERS (0x100 to 0x15F)
0x100-0x101 Undefined RESERVED R RESERVED
0x102 Undefined B0_TIME_0 R/W Timing Adjustment for Bank 0 (0° Clock) Register
0x103 Undefined B0_TIME_90 R/W Timing Adjustment for Bank 0 (–90° Clock) Register
0x104-0x111 Undefined RESERVED R RESERVED
0x112 Undefined B1_TIME_0 R/W Timing Adjustment for Bank 1 (0° Clock) Register
0x113 Undefined B1_TIME_90 R/W Timing Adjustment for Bank 1 (–90° Clock) Register
0x114-0x121 Undefined RESERVED R RESERVED
0x122 Undefined B2_TIME_0 R/W Timing Adjustment for Bank 2 (0° Clock) Register
0x123 Undefined B2_TIME_90 R/W Timing Adjustment for Bank 2 (–90° Clock) Register
0x124-0x131 Undefined RESERVED R RESERVED
0x132 Undefined B3_TIME_0 R/W Timing Adjustment for Bank 3 (0° Clock) Register
0x133 Undefined B3_TIME_90 R/W Timing Adjustment for Bank 3 (–90° Clock) Register
0x134-0x141 Undefined RESERVED R RESERVED
0x142 Undefined B4_TIME_0 R/W Timing Adjustment for Bank 4 (0° Clock) Register
0x143 Undefined B4_TIME_90 R/W Timing Adjustment for Bank 4 (–90° Clock) Register
0x144-0x151 Undefined RESERVED R RESERVED
0x152 Undefined B5_TIME_0 R/W Timing Adjustment for Bank 5 (0° Clock) Register
0x153 Undefined B5_TIME_90 R/W Timing Adjustment for Bank 5 (–90° Clock) Register
0x154-0x15F Undefined RESERVED R RESERVED
LSB CONTROL REGISTERS (0x160 to 0x1FF)
0x160 0x00 ENC_LSB R/W LSB Control Bit Output Register
0x161-0x1FF Undefined RESERVED R RESERVED
JESD204B REGISTERS (0x200 to 0x20F)
0x200 0x01 JESD_EN R/W JESD204B Enable Register
0x201 0x02 JMODE R/W JESD204B Mode (JMODE) Register
0x202 0x1F KM1 R/W JESD204B K Parameter Register
0x203 0x01 JSYNC_N R/W JESD204B Manual SYNC Request Register
0x204 0x02 JCTRL R/W JESD204B Control Register
0x205 0x00 JTEST R/W JESD204B Test Pattern Control Register
0x206 0x00 DID R/W JESD204B DID Parameter Register
0x207 0x00 FCHAR R/W JESD204B Frame Character Register
0x208 Undefined JESD_STATUS R/W JESD204B, System Status Register
0x209 0x00 PD_CH R/W JESD204B Channel Power-Down
0x20A 0x00 JEXTRA_A R/W JESD204B Extra Lane Enable (Link A)
0x20B 0x00 JEXTRA_B R/W JESD204B Extra Lane Enable (Link B)
0x20C-0x210 Undefined RESERVED R RESERVED
DIGITAL DOWN CONVERTER REGISTERS (0x210-0x2AF)
0x211 0xF2 OVR_T0 R/W Overrange Threshold 0 Register
0x212 0xAB OVR_T1 R/W Overrange Threshold 1 Register
0x213 0x07 OVR_CFG R/W Overrange Configuration Register
0x214-0x296 Undefined RESERVED R RESERVED
0x297 Undefined SPIN_ID R Spin Identification Value
0x298-0x2AF Undefined RESERVED R RESERVED
SYSREF CALIBRATION REGISTERS (0x2B0 to 0x2BF)
0x2B0 0x00 SRC_EN R/W SYSREF Calibration Enable Register
0x2B1 0x05 SRC_CFG R/W SYSREF Calibration Configuration Register
0x2B2-0x2B4 Undefined SRC_STATUS R SYSREF Calibration Status
0x2B5-0x2B7 0x00 TAD R/W DEVCLK Aperture Delay Adjustment Register
0x2B8 0x00 TAD_RAMP R/W DEVCLK Timing Adjust Ramp Control Register
0x2B9-0x2BF Undefined RESERVED R RESERVED
ALARM REGISTERS (0x2C0 to 0x2C2)
0x2C0 Undefined ALARM R Alarm Interrupt Status Register
0x2C1 0x1F ALM_STATUS R/W Alarm Status Register
0x2C2 0x1F ALM_MASK R/W Alarm Mask Register