JAJSMH3B December   1997  – November 2024 OPA134 , OPA2134 , OPA4134

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information - OPA134
    5. 5.5 Thermal Information - OPA2134
    6. 5.6 Thermal Information - OPA4134
    7. 5.7 Electrical Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Feature Description
      1. 6.2.1 Total Harmonic Distortion
      2. 6.2.2 Distortion Measurements
      3. 6.2.3 Source Impedance and Distortion
      4. 6.2.4 Phase Reversal Protection
      5. 6.2.5 Output Current Limit
    3. 6.3 Functional Block Diagram
    4. 6.4 Device Functional Modes
      1. 6.4.1 Noise Performance
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1 Operating Voltage
      2. 7.1.2 Offset Voltage Trim
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curve
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Development Support
        1. 8.1.1.1 Analog Filter Designer
        2. 8.1.1.2 TINA-TI™シミュレーション ソフトウェア (無償ダウンロード)
        3. 8.1.1.3 TI のリファレンス・デザイン
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 ドキュメントの更新通知を受け取る方法
    4. 8.4 サポート・リソース
    5. 8.5 Trademarks
    6. 8.6 静電気放電に関する注意事項
    7. 8.7 用語集
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

9 Revision History

Changes from Revision A (April 2015) to Revision B (August 2024)

  • ドキュメント全体にわたって表、図、相互参照の採番方法を更新Go
  • 「特長」の開ループ ゲイン負荷条件を更新 Go
  • クワッド バージョン デバイスの PDIP パッケージ オプションを削除Go
  • 「製品情報」表を更新Go
  • 表紙の図で W の記号を Ω に変更 (誤字)Go
  • Updated Pin Configuration and Functions formatGo
  • Changed OPA134 pin 1 and 8 from "Offset Trim" to "NC"Go
  • Changed input voltage from (V–) – 0.7V to (V+) + 0.7V to (V–) – 0.5V to (V+) + 0.5V in Absolute Maximum Ratings Go
  • Added input current and related footnote to Absolute Maximum Ratings Go
  • Added Thermal Information Go
  • Updated format of Electrical Characteristics Go
  • Updated nominal conditions in the header of Electrical Characteristics Go
  • Changed headroom from 23.6dB to 21.3dBGo
  • Deleted slew rate MINGo
  • Changed overload recovery time from 0.5µs to 0.6µsGo
  • Changed input offset voltage MIN from ±0.5mV to ±1mV and MAX from ±2mV to ±3.5mVGo
  • Deleted input offset voltage over temperature MAXGo
  • Changed channel separation from 135dB to 128dB for dc, and from 130dB to 126dB for f = 20kHz Go
  • Deleted note 3Go
  • Added ± to input bias current TYPGo
  • Changed common-mode voltage MAX value from (V+) – 2.5V to (V+) – 3.5VGo
  • Updated common-mode rejection ratio and common-mode input impedance test conditionsGo
  • Changed differential input impedance from 1013Ω || 2pF to 1013Ω || 8pFGo
  • Changed common-mode input impedance from 1013Ω || 5pF to 1013Ω || 6pFGo
  • Deleted open-loop voltage gain for RL = 600ΩGo
  • Deleted voltage output for RL = 600ΩGo
  • Moved voltage output negative MIN values to MAX valuesGo
  • Deleted output currentGo
  • Deleted note 1 from Electrical Characteristics Go
  • Changed typos in typical characteristic graphs; corrected ohms symbol (Ω) and radical symbol (√)Go
  • Changed test condition for Typical Characteristics from VS = 15V to VS = ±15V (typo)Go
  • Changed Figure 26, Small-Signal Overshoot vs Load Capacitance into new Figures 5-23 and 5-24Go
  • Deleted old Figure 20, Output Voltage Swing vs Output Current, Figure 21, Offset Voltage Production Distribution, Figure 22, Offset Voltage Drift Production Distribution Go
  • Updated Functional Block Diagram Go
  • Updated Offset Voltage Trim Go
  • Updated OPA134 Layout Example for the Noninverting Configuration Go

Changes from Revision * (September 2000) to Revision A (April 2015)

  • ESD 定格の表、「機能説明」セクション、「デバイスの機能モード」セクション、「アプリケーションと実装」セクション、「電源に関する推奨事項」セクション、「レイアウト」セクション、「デバイスおよびドキュメントのサポート」セクション、「メカニカル、パッケージ、および注文情報」セクションを追加。 Go