JAJSTC8A February   2024  – April 2024 LP5867

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7.     14
    8. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Time-Multiplexing Matrix
      2. 7.3.2 Analog Dimming (Current Gain Control)
        1. 7.3.2.1 Global 3-Bits Maximum Current (MC) Setting
        2. 7.3.2.2 3 Groups of 7-Bits Color Current (CC) Setting
        3. 7.3.2.3 Individual 8-bit Dot Current (DC) Setting
      3. 7.3.3 PWM Dimming
        1. 7.3.3.1 Individual 8-Bit / 16-Bit PWM for Each LED Dot
        2. 7.3.3.2 Programmable Groups of 8-Bit PWM Dimming
        3. 7.3.3.3 8-Bit PWM for Global Dimming
      4. 7.3.4 ON and OFF Control
      5. 7.3.5 Data Refresh Mode
      6. 7.3.6 Full Addressable SRAM
      7. 7.3.7 Protections and Diagnostics
        1. 7.3.7.1 LED Open Detection
        2. 7.3.7.2 LED Short Detection
        3. 7.3.7.3 Thermal Shutdown
        4. 7.3.7.4 UVLO (Under Voltage Lock Out)
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
      1. 7.5.1 Interface Selection
      2. 7.5.2 I2C Interface
        1. 7.5.2.1 I2C Data Transactions
        2. 7.5.2.2 I2C Data Format
        3. 7.5.2.3 Multiple Devices Connection
      3. 7.5.3 Programming
        1. 7.5.3.1 SPI Data Transactions
        2. 7.5.3.2 SPI Data Format
        3. 7.5.3.3 Multiple Devices Connection
    6. 7.6 Register Maps
  9. 8 Register Maps
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Application
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
        1. 9.2.3.1 Program Procedure
      4. 9.2.4 Application Performance Plots
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 VDD Input Supply Recommendations
      2. 9.3.2 VLED Input Supply Recommendations
      3. 9.3.3 VIO Input Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 ドキュメントの更新通知を受け取る方法
    2. 10.2 サポート・リソース
    3. 10.3 Trademarks
    4. 10.4 静電気放電に関する注意事項
    5. 10.5 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

9.2.3 Detailed Design Procedure

LP5867 requires an external capacitor CVCAP, whose value is 1μF connected from VCAP to GND for proper operation of internal LDO. The device must be placed as close to the device as possible.

TI recommends that 1-μF capacitors be placed between VCC / VLED with GND, and a 1nF capacitor placed between VIO with GND. Place the capacitors as close to the device as possible.

Pull-up resistors Rpull-up are requirement for SCL and SDA when using I2C as communication method. In typical applications, TI recommends 1.8kΩ to 4.7kΩ resistors.

To decrease thermal dissipation from device to ambient, resistors RCS can optionally be placed in serial with the LED. Voltage drop on these resistors must left enough margins for VSAT to ensure the device works normally.