SNLU223D August   2017  – February 2023 DS90UB954-Q1

 

  1.   DS90UB954-Q1EVM Deserializer User's Guide
  2. 1 Trademarks
  3. 2 Introduction
  4. 3 Quick Start Guide
    1. 3.1 System Requirements
      1. 3.1.1 Included Components
      2. 3.1.2 Additional Required Components
    2. 3.2 Applications Diagram
    3. 3.3 Major Components of DS90UB954-Q1EVM
    4. 3.4 DS90UB954-Q1EVM Setup
  5. 4 DS90UB954-Q1EVM Board Configuration
    1. 4.1 Default Configuration
    2. 4.2 Power Supply
    3. 4.3 Power-over-Coax Interface
    4. 4.4 MIPI CSI-2 Output Signals
    5. 4.5 FPD-Link III Signals
    6. 4.6 I2C Interface
    7. 4.7 Control Interface
  6. 5 Enable and Reset
  7. 6 Use with DS90UB936-Q1
  8. 7 Typical Connection and Test Equipment
  9. 8 Termination Device
  10. 9 Typical Test Setup
  11. 10Equipment References
  12. 11Cable References
  13. 12Software for DS90UB954Q1-EVM Evaluation - Analog LaunchPAD (ALP) Software Setup
    1. 12.1 System Requirements
    2. 12.2 Download Contents
    3. 12.3 Installation of the ALP Software
    4. 12.4 Startup - First Launch
  14. 13Using ALP and DS90UB954 Profile
    1. 13.1 Information Tab
    2. 13.2 Registers Tab
    3. 13.3 Registers Tab - Address 0x00 Expanded
      1. 13.3.1 Port Specific Registers
      2. 13.3.2 36
    4. 13.4 Saving and Loading Register Settings
    5. 13.5 Scripting Tab
      1. 13.5.1 Example Functions
        1. 13.5.1.1 Local I2C Reads/Writes
        2. 13.5.1.2 General I2C Reads/Writes:
        3. 13.5.1.3 I2C Reads/Writes with Multi-Byte Register Addresses
    6. 13.6 GPIO Tab
    7. 13.7 Forwarding Tab
    8. 13.8 CSI Registers Tab
    9. 13.9 Remote Registers Tab
  15. 14Troubleshooting ALP Software
    1. 14.1 ALP Does Not Detect The EVM
    2. 14.2 USB2ANY Firmware Issues
  16. 15DS90UB954-Q1EVM PCB Schematics, Layout and Bill of Materials - DS90UB954-Q1EVM Schematic
  17. 16DS90UB954-Q1 EVM PCB Layout
  18. 17DS90UB954-Q1EVM Bill of Materials
  19. 18Revision History

3.4 DS90UB954-Q1EVM Setup

  1. Use the mini USB to USB cable to connect J2 to computer USB port for register programming and open Analog LaunchPAD. See GUID-53048FDE-4862-40B2-8459-C5BAAC5DD6A2.html#GUID-53048FDE-4862-40B2-8459-C5BAAC5DD6A2 for details on installing and using Analog LaunchPAD.
  2. Configure jumpers J8, J10, J11, J15, J16, J23, J27 to set device’s operating modes. The default configuration can be seen in GUID-BC1492B7-0A85-4EDB-B31D-7EC6E195E118.html#T4697723-7.
  3. Configure Power-over-Coax power supplies for RX0 and RX1 with J18 and J17 respectively.
  4. Connect the DS90UB954-Q1EVM to DS90UB953-Q1EVM (or variant) to RX0 and/or DS90UB933-Q1EVM to RX1 using a coax cable.
  5. Interface MIPI CSI-2 output signals (J24) to test equipment or host processor (optional, not required to check status of FPD-Link III connection between serializer and deserializer).
  6. Provide power to board. TI recommends using current limited bench supply to provide power to J1 (barrel jack) or J3.