SPRUJ86C October   2023  – August 2024 AM263P2 , AM263P4 , AM263P4-Q1

 

  1.   1
  2.   Description
  3.   Features
  4.   4
  5. 1Evaluation Module Overview
    1. 1.1 Introduction
      1.      Preface: Read This First
        1. 1.1.1.1 Sitara MCU+ Academy
        2. 1.1.1.2 Important Usage Notes
    2. 1.2 Kit Contents
    3. 1.3 Device Information
      1. 1.3.1 HSEC 180-pin Control Card Docking Station
      2. 1.3.2 Security
  6. 2Hardware
    1. 2.1  Component Identification
    2. 2.2  Power Requirements
      1. 2.2.1 Power Input Using USB Type-C Connector
      2. 2.2.2 Power Status LEDs
      3. 2.2.3 Power Tree
      4. 2.2.4 Power Sequence
      5. 2.2.5 PMIC
    3. 2.3  Functional Block Diagram
    4. 2.4  Reset
    5. 2.5  Clock
    6. 2.6  Boot Mode Selection
    7. 2.7  JTAG Path Selection
    8. 2.8  Header Information
    9. 2.9  GPIO Mapping
    10. 2.10 Push Buttons
    11. 2.11 Interfaces
      1. 2.11.1  Memory Interface
        1. 2.11.1.1 OSPI/QSPI
        2. 2.11.1.2 Board ID EEPROM
      2. 2.11.2  Ethernet Interface
        1. 2.11.2.1 Control Card Ethernet Routing
        2. 2.11.2.2 On Board Ethernet PHY
        3. 2.11.2.3 LED Indication in RJ45 Connector
        4. 2.11.2.4 Ethernet Add On Board Connector
      3. 2.11.3  I2C
      4. 2.11.4  Industrial Application LEDs
      5. 2.11.5  SPI
      6. 2.11.6  UART
      7. 2.11.7  MCAN
      8. 2.11.8  FSI
      9. 2.11.9  JTAG
      10. 2.11.10 Test Automation Header
      11. 2.11.11 LIN
      12. 2.11.12 MMC
      13. 2.11.13 ADC and DAC
    12. 2.12 HSEC Pinout and Pinmux Mapping
  7. 3Hardware Design Files
  8. 4Additional Information
    1. 4.1 If You Need Assistance
    2. 4.2 Trademarks
  9. 5Related Documentation
    1. 5.1 Supplemental Content
      1.      5.1.A E1 Board Modifications
      2.      5.1.B E2 Design Changes
      3.      5.1.C A Design Changes
  10. 6References
    1. 6.1 Reference Documents
    2. 6.2 Other TI Components Used in This Design
  11. 7Revision History
  12. 8Revision History

2.2.2 Power Status LEDs

Multiple power-indication LEDs are provided on-board to indicate to users the output status of major supplies. The LEDs indicate power across various domains as shown in the table below.

Table 2-2 Power Status LEDs(1)
Name Default Status Operation Function
LD1 OFF Type-C CC Logic Power Error Indication. Type-C connection not supplying 5V at 3A
LD2 ON VMAIN_12V0 Power indicator for VMAIN 12V supply
LD3 ON VSYS_3V3_LDO1 Power indicator for PMIC LDO 3.3V supply
LD4 ON VSYS_1V2_PG Power Good indicator for 1.2V supply rail
LD5 ON VSYS_TA_3V3 Power indicator test automation header 3.3V supply
LD6 OFF USER_LED0 User Programmable Red LED
LD7 OFF USER_LED1 User Programmable Green LED
LD8 OFF PMIC_SAFE_OUT2 Safety Error indicator output from PMIC
LD9 OFF XDS110_PROG_STAZ1 LED glows after XDS configuration
LD10 OFF XDS110_PROG_STAZ2
LD19 OFF SAFETY_ERROR Safety error output status pin from AM263Px
LD20 ON VCC_1V8_LDO4 Power indicator PMIC LDO 1.8 Vsupply
LD21 ON VDD_5V0_LDO3 Power indicator for PMIC LDO 5.0V supply
LD22 ON VSYS_3V3_LDO2 Power indicator for PMIC LDO 3.3V supply
(1) LD[19:22] are not included in the E1 version of the Control Card.
AM263P1, AM263P1-Q1, AM263P2, AM263P2-Q1, AM263P4, AM263P4-Q1 Power Status LEDs Figure 2-5 Power Status LEDs