SPRUJG2 December   2024 AM62D-Q1

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   5
  6. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
    4. 1.4 Device Information
    5. 1.5 EVM Revisions and Assembly Variants
  7. 2Hardware
    1. 2.1  Additional Images
    2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Supported Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers to Support Application Specific Add‐On Boards
    3. 2.3  Power Requirement
    4. 2.4  Setup and Configuration
      1. 2.4.1 EVM DIP Switches
      2. 2.4.2 Boot modes
      3. 2.4.3 User Test LEDs
    5. 2.5  Power ON/OFF Procedures
      1. 2.5.1 Power ON Procedure
      2. 2.5.2 Power OFF Procedure
      3. 2.5.3 Power Test Points
    6. 2.6  Interfaces
      1. 2.6.1  AM62D Audio EVM Interface Mapping
      2. 2.6.2  Audio Interface
        1. 2.6.2.1 Audio Stereo Lineouts
        2. 2.6.2.2 Audio Microphone / Line In
      3. 2.6.3  JTAG Interface
      4. 2.6.4  UART Interface
      5. 2.6.5  USB Interface
        1. 2.6.5.1 USB2.0 Type-A Interface
        2. 2.6.5.2 USB2.0 Type-C Interface
      6. 2.6.6  MCAN Interface
      7. 2.6.7  Memory Interfaces
        1. 2.6.7.1 LPDDR4 Interface
        2. 2.6.7.2 Octal Serial Peripheral Interface (OSPI)
        3. 2.6.7.3 MMC Interfaces
          1. 2.6.7.3.1 MMC0 - eMMC Interface
          2. 2.6.7.3.2 MMC1 - MicroSD Interface
        4. 2.6.7.4 Board ID EEPROM
      8. 2.6.8  Ethernet Interface
      9. 2.6.9  CPSW Ethernet 1 and CPSW Ethernet 2
      10. 2.6.10 GPIO Port Expander
      11. 2.6.11 GPIO Mapping
    7. 2.7  Power
      1. 2.7.1 Power Input
      2. 2.7.2 Power Supply
      3. 2.7.3 Power Sequencing
      4. 2.7.4 AM62D SOC Power
      5. 2.7.5 Current Monitoring
    8. 2.8  Clocking
      1. 2.8.1 Peripheral Ref Clock
    9. 2.9  Reset
    10. 2.10 CPLD Mapping
    11. 2.11 Audio Expansion Connectors (Headers)
      1. 2.11.1 Audio Expansion Connector 1
      2. 2.11.2 Audio Expansion Connector 2
    12. 2.12 Interrupt
    13. 2.13 I2C Address Mapping
  8. 3Hardware Design Files
  9. 4Compliance Information
    1. 4.1 Compliance and Certifications
  10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
    2. 5.2 Trademarks

2.5 Power ON/OFF Procedures

Power to the EVM is provided through an external power supply with PD capability to either of the two USB Type-C Ports.

Note: TI recommends the maximum length of the I/O cables not exceed 3 meters.