SWCU192 November 2021 CC1312R7 , CC1352P7 , CC2652P7 , CC2652R7
#EVENT_FABRIC_EVENT_FABRIC_MAP1_TABLE_1 lists the memory-mapped registers for the EVENT_FABRIC registers. All register offset addresses not listed in #EVENT_FABRIC_EVENT_FABRIC_MAP1_TABLE_1 should be considered as reserved locations and the register contents should not be modified.
Complex bit access types are encoded to fit into small table cells. #EVENT_FABRIC_EVENT_FABRIC_MAP1_LEGEND shows the codes that are used for access types in this section.
Access Type | Code | Description |
---|---|---|
Read Type | ||
R | R | Read |
Write Type | ||
W | W | Write |
Reset or Default Value | ||
-n | Value after reset or the default value |
CPUIRQSEL0 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL0_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL0_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-4h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 4h | Read only selection value
4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings |
CPUIRQSEL1 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL1_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL1_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 1
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-9h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 9h | Read only selection value
9h = Interrupt event from I2C |
CPUIRQSEL2 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL2_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL2_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 2
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1Eh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1Eh | Read only selection value
1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event |
CPUIRQSEL3 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL3_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL3_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 3
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1Fh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1Fh | Read only selection value
1Fh = PKA Interrupt event |
CPUIRQSEL4 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL4_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL4_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 4
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-7h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 7h | Read only selection value
7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting |
CPUIRQSEL5 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL5_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL5_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 5
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-24h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 24h | Read only selection value
24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS |
CPUIRQSEL6 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL6_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL6_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 6
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1Ch | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1Ch | Read only selection value
1Ch = AUX software event 0, triggered by AUX_EVCTL:SWEVSET.SWEV0, also available as AUX_EVENT0 AON wake up event. |
CPUIRQSEL7 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL7_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL7_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 7
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-22h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 22h | Read only selection value
22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS |
CPUIRQSEL8 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL8_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL8_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 8
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-23h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 23h | Read only selection value
23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS |
CPUIRQSEL9 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL9_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL9_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 9
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1Bh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1Bh | Read only selection value
1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event |
CPUIRQSEL10 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL10_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL10_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 10
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1Ah | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1Ah | Read only selection value
1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG |
CPUIRQSEL11 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL11_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL11_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 11
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-19h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 19h | Read only selection value
19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG |
CPUIRQSEL12 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL12_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL12_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 12
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-8h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 8h | Read only selection value
8h = Interrupt event from I2S |
CPUIRQSEL13 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL13_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL13_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 13
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1Dh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1Dh | Read only selection value
1Dh = AUX software event 1, triggered by AUX_EVCTL:SWEVSET.SWEV1, also available as AUX_EVENT2 AON wake up event. |
CPUIRQSEL14 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL14_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL14_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 14
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-18h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 18h | Read only selection value
18h = Watchdog interrupt event, controlled by WDT:CTL.INTEN |
CPUIRQSEL15 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL15_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL15_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 15
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-10h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 10h | Read only selection value
10h = GPT0A interrupt event, controlled by GPT0:TAMR |
CPUIRQSEL16 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL16_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL16_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 16
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-11h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 11h | Read only selection value
11h = GPT0B interrupt event, controlled by GPT0:TBMR |
CPUIRQSEL17 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL17_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL17_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 17
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-12h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 12h | Read only selection value
12h = GPT1A interrupt event, controlled by GPT1:TAMR |
CPUIRQSEL18 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL18_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL18_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 18
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-13h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 13h | Read only selection value
13h = GPT1B interrupt event, controlled by GPT1:TBMR |
CPUIRQSEL19 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL19_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL19_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 19
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-Ch | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | Ch | Read only selection value
Ch = GPT2A interrupt event, controlled by GPT2:TAMR |
CPUIRQSEL20 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL20_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL20_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 20
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-Dh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | Dh | Read only selection value
Dh = GPT2B interrupt event, controlled by GPT2:TBMR |
CPUIRQSEL21 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL21_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL21_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 21
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-Eh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | Eh | Read only selection value
Eh = GPT3A interrupt event, controlled by GPT3:TAMR |
CPUIRQSEL22 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL22_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL22_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 22
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-Fh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | Fh | Read only selection value
Fh = GPT3B interrupt event, controlled by GPT3:TBMR |
CPUIRQSEL23 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL23_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL23_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 23
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-5Dh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 5Dh | Read only selection value
5Dh = CRYPTO result available interupt event, the corresponding flag is found here CRYPTO:IRQSTAT.RESULT_AVAIL. Controlled by CRYPTO:IRQSTAT.RESULT_AVAIL |
CPUIRQSEL24 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL24_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL24_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 24
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-27h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 27h | Read only selection value
27h = Combined DMA done, corresponding flags are here UDMA0:REQDONE |
CPUIRQSEL25 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL25_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL25_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 25
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-26h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 26h | Read only selection value
26h = DMA bus error, corresponds to UDMA0:ERROR.STATUS |
CPUIRQSEL26 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL26_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL26_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 26
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-15h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 15h | Read only selection value
15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT |
CPUIRQSEL27 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL27_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL27_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 27
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-64h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 64h | Read only selection value
64h = Software event 0, triggered by SWEV.SWEV0 |
CPUIRQSEL28 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL28_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL28_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 28
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-Bh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | Bh | Read only selection value
Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS |
CPUIRQSEL29 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL29_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL29_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 29
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-1h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 1h | Read only selection value
1h = AON programmable event 0. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG0_EV |
CPUIRQSEL30 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL30_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL30_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 30
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-0h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 0h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 2h = AON programmable event 1. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG1_EV 3h = AON programmable event 2. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG2_EV 8h = Interrupt event from I2S Ah = AUX Software event 0, AUX_EVCTL:SWEVSET.SWEV0 14h = DMA done for software tiggered UDMA channel 0, see UDMA0:SOFTREQ 16h = DMA done for software tiggered UDMA channel 18, see UDMA0:SOFTREQ 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 5Eh = CRYPTO DMA input done event, the correspondingg flag is CRYPTO:IRQSTAT.DMA_IN_DONE. Controlled by CRYPTO:IRQEN.DMA_IN_DONE 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
CPUIRQSEL31 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL31_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL31_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 31
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-6Ah | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 6Ah | Read only selection value
6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA |
CPUIRQSEL32 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL32_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL32_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 32
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-73h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 73h | Read only selection value
73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS |
CPUIRQSEL33 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL33_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL33_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 33
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-68h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 68h | Read only selection value
68h = TRNG Interrupt event, controlled by TRNG:IRQEN.EN |
CPUIRQSEL34 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL34_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL34_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 34
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-6h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 6h | Read only selection value
6h = Combined event from Oscillator control |
CPUIRQSEL35 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL35_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL35_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 35
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-38h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 38h | Read only selection value
38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 |
CPUIRQSEL36 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL36_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL36_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 36
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-25h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 25h | Read only selection value
25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS |
CPUIRQSEL37 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL37_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CPUIRQSEL37_TABLE.
Return to the Summary Table.
Output Selection for CPU Interrupt 37
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-5h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 5h | Read only selection value
5h = Combined event from battery monitor |
RFCSEL0 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL0_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL0_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-3Dh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 3Dh | Read only selection value
3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT |
RFCSEL1 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL1_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL1_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 1
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-3Eh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 3Eh | Read only selection value
3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT |
RFCSEL2 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL2_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL2_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 2
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-3Fh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 3Fh | Read only selection value
3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT |
RFCSEL3 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL3_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL3_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 3
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-40h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 40h | Read only selection value
40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT |
RFCSEL4 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL4_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL4_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 4
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-41h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 41h | Read only selection value
41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT |
RFCSEL5 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL5_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL5_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 5
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-42h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 42h | Read only selection value
42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT |
RFCSEL6 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL6_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL6_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 6
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-43h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 43h | Read only selection value
43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT |
RFCSEL7 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL7_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL7_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 7
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-44h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 44h | Read only selection value
44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT |
RFCSEL8 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL8_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL8_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 8
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-77h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 77h | Read only selection value
77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN |
RFCSEL9 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL9_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_RFCSEL9_TABLE.
Return to the Summary Table.
Output Selection for RFC Event 9
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-2h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 2h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 1h = AON programmable event 0. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG0_EV 2h = AON programmable event 1. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG1_EV 8h = Interrupt event from I2S Ah = AUX Software event 0, AUX_EVCTL:SWEVSET.SWEV0 18h = Watchdog interrupt event, controlled by WDT:CTL.INTEN 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 27h = Combined DMA done, corresponding flags are here UDMA0:REQDONE 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 5Dh = CRYPTO result available interupt event, the corresponding flag is found here CRYPTO:IRQSTAT.RESULT_AVAIL. Controlled by CRYPTO:IRQSTAT.RESULT_AVAIL 64h = Software event 0, triggered by SWEV.SWEV0 65h = Software event 1, triggered by SWEV.SWEV1 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 79h = Always asserted |
GPT0ACAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT0ACAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT0ACAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT0 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-55h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 55h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 55h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT0 wil be routed here. 56h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT1 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
GPT0BCAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT0BCAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT0BCAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT0 1
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-56h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 56h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 55h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT0 wil be routed here. 56h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT1 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
GPT1ACAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT1ACAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT1ACAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT1 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-57h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 57h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 57h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT2 wil be routed here. 58h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT3 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
GPT1BCAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT1BCAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT1BCAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT1 1
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-58h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 58h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 57h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT2 wil be routed here. 58h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT3 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
GPT2ACAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT2ACAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT2ACAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT2 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-59h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 59h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 59h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT4 wil be routed here. 5Ah = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT4 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
GPT2BCAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT2BCAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT2BCAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT2 1
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-5Ah | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 5Ah | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 59h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT4 wil be routed here. 5Ah = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT4 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
UDMACH1SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH1SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH1SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 1 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-31h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 31h | Read only selection value
31h = UART0 RX DMA single request, controlled by UART0:DMACTL.RXDMAE |
UDMACH1BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH1BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH1BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 1 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-30h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 30h | Read only selection value
30h = UART0 RX DMA burst request, controlled by UART0:DMACTL.RXDMAE |
UDMACH2SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH2SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH2SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 2 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-33h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 33h | Read only selection value
33h = UART0 TX DMA single request, controlled by UART0:DMACTL.TXDMAE |
UDMACH2BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH2BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH2BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 2 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-32h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 32h | Read only selection value
32h = UART0 TX DMA burst request, controlled by UART0:DMACTL.TXDMAE |
UDMACH3SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH3SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH3SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 3 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-29h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 29h | Read only selection value
29h = SSI0 RX DMA single request, controlled by SSI0:DMACR.RXDMAE |
UDMACH3BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH3BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH3BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 3 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-28h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 28h | Read only selection value
28h = SSI0 RX DMA burst request , controlled by SSI0:DMACR.RXDMAE |
UDMACH4SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH4SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH4SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 4 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-2Bh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 2Bh | Read only selection value
2Bh = SSI0 TX DMA single request, controlled by SSI0:DMACR.TXDMAE |
UDMACH4BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH4BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH4BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 4 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-2Ah | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 2Ah | Read only selection value
2Ah = SSI0 TX DMA burst request , controlled by SSI0:DMACR.TXDMAE |
UDMACH5SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH5SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH5SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 5 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-35h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 35h | Read only selection value
35h = UART1 RX DMA single request, controlled by UART1:DMACTL.RXDMAE |
UDMACH5BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH5BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH5BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 5 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-34h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 34h | Read only selection value
34h = UART1 RX DMA burst request, controlled by UART1:DMACTL.RXDMAE |
UDMACH6SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH6SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH6SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 6 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-37h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 37h | Read only selection value
37h = UART1 TX DMA single request, controlled by UART1:DMACTL.TXDMAE |
UDMACH6BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH6BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH6BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 6 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-36h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 36h | Read only selection value
36h = UART1 TX DMA burst request, controlled by UART1:DMACTL.TXDMAE |
UDMACH7SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH7SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH7SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 7 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-75h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 75h | Read only selection value
75h = DMA single request event from AUX, configured by AUX_EVCTL:DMACTL |
UDMACH7BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH7BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH7BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 7 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-76h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 76h | Read only selection value
76h = DMA burst request event from AUX, configured by AUX_EVCTL:DMACTL |
UDMACH8SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH8SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH8SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 8 SREQ
Single request is ignored for this channel
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-74h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 74h | Read only selection value
74h = DMA sofware trigger from AUX, triggered by AUX_EVCTL:DMASWREQ.START |
UDMACH8BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH8BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH8BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 8 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-74h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 74h | Read only selection value
74h = DMA sofware trigger from AUX, triggered by AUX_EVCTL:DMASWREQ.START |
UDMACH9SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH9SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH9SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 9 SREQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT0 as GPT0:RIS.DMAARIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-45h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 45h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 45h = Not used tied to 0 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH9BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH9BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH9BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 9 REQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT0 as GPT0:RIS.DMAARIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-4Dh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 4Dh | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH10SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH10SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH10SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 10 SREQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT0 as GPT0:RIS.DMABRIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-46h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 46h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 46h = Not used tied to 0 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH10BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH10BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH10BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 10 REQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT0 as GPT0:RIS.DMABRIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-4Eh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 4Eh | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH11SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH11SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH11SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 11 SREQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT1 as GPT1:RIS.DMAARIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-47h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 47h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 47h = Not used tied to 0 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH11BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH11BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH11BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 11 REQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT1 as GPT1:RIS.DMAARIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-4Fh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 4Fh | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH12SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH12SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH12SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 12 SREQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT1 as GPT1:RIS.DMABRIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-48h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 48h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 48h = Not used tied to 0 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH12BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH12BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH12BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 12 REQ
DMA_DONE for the corresponding DMA channel is available as interrupt on GPT1 as GPT1:RIS.DMABRIS
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-50h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 50h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 79h = Always asserted |
UDMACH13BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH13BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH13BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 13 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-3h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 3h | Read only selection value
3h = AON programmable event 2. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG2_EV |
UDMACH14BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH14BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH14BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 14 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-1h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 1h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 1h = AON programmable event 0. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG0_EV 2h = AON programmable event 1. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG1_EV 3h = AON programmable event 2. Event selected by AON_EVENT MCU event selector, AON_EVENT:EVTOMCUSEL.AON_PROG2_EV 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 8h = Interrupt event from I2S 9h = Interrupt event from I2C Ah = AUX Software event 0, AUX_EVCTL:SWEVSET.SWEV0 Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS Ch = GPT2A interrupt event, controlled by GPT2:TAMR Dh = GPT2B interrupt event, controlled by GPT2:TBMR Eh = GPT3A interrupt event, controlled by GPT3:TAMR Fh = GPT3B interrupt event, controlled by GPT3:TBMR 10h = GPT0A interrupt event, controlled by GPT0:TAMR 11h = GPT0B interrupt event, controlled by GPT0:TBMR 12h = GPT1A interrupt event, controlled by GPT1:TAMR 13h = GPT1B interrupt event, controlled by GPT1:TBMR 14h = DMA done for software tiggered UDMA channel 0, see UDMA0:SOFTREQ 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 16h = DMA done for software tiggered UDMA channel 18, see UDMA0:SOFTREQ 18h = Watchdog interrupt event, controlled by WDT:CTL.INTEN 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Dh = AUX software event 1, triggered by AUX_EVCTL:SWEVSET.SWEV1, also available as AUX_EVENT2 AON wake up event. 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 1Fh = PKA Interrupt event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 26h = DMA bus error, corresponds to UDMA0:ERROR.STATUS 27h = Combined DMA done, corresponding flags are here UDMA0:REQDONE 28h = SSI0 RX DMA burst request , controlled by SSI0:DMACR.RXDMAE 29h = SSI0 RX DMA single request, controlled by SSI0:DMACR.RXDMAE 2Ah = SSI0 TX DMA burst request , controlled by SSI0:DMACR.TXDMAE 2Bh = SSI0 TX DMA single request, controlled by SSI0:DMACR.TXDMAE 2Ch = SSI1 RX DMA burst request , controlled by SSI0:DMACR.RXDMAE 2Dh = SSI1 RX DMA single request, controlled by SSI0:DMACR.RXDMAE 2Eh = SSI1 TX DMA burst request , controlled by SSI0:DMACR.TXDMAE 2Fh = SSI1 TX DMA single request, controlled by SSI0:DMACR.TXDMAE 30h = UART0 RX DMA burst request, controlled by UART0:DMACTL.RXDMAE 31h = UART0 RX DMA single request, controlled by UART0:DMACTL.RXDMAE 32h = UART0 TX DMA burst request, controlled by UART0:DMACTL.TXDMAE 33h = UART0 TX DMA single request, controlled by UART0:DMACTL.TXDMAE 34h = UART1 RX DMA burst request, controlled by UART1:DMACTL.RXDMAE 35h = UART1 RX DMA single request, controlled by UART1:DMACTL.RXDMAE 36h = UART1 TX DMA burst request, controlled by UART1:DMACTL.TXDMAE 37h = UART1 TX DMA single request, controlled by UART1:DMACTL.TXDMAE 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 4Dh = GPT0A DMA trigger event. Configured by GPT0:DMAEV 4Eh = GPT0B DMA trigger event. Configured by GPT0:DMAEV 4Fh = GPT1A DMA trigger event. Configured by GPT1:DMAEV 50h = GPT1B DMA trigger event. Configured by GPT1:DMAEV 51h = GPT2A DMA trigger event. Configured by GPT2:DMAEV 52h = GPT2B DMA trigger event. Configured by GPT2:DMAEV 53h = GPT3A DMA trigger event. Configured by GPT3:DMAEV 54h = GPT3B DMA trigger event. Configured by GPT3:DMAEV 55h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT0 wil be routed here. 56h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT1 wil be routed here. 57h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT2 wil be routed here. 58h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT3 wil be routed here. 59h = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT4 wil be routed here. 5Ah = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT4 wil be routed here. 5Bh = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT6 wil be routed here. 5Ch = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT7 wil be routed here. 5Dh = CRYPTO result available interupt event, the corresponding flag is found here CRYPTO:IRQSTAT.RESULT_AVAIL. Controlled by CRYPTO:IRQSTAT.RESULT_AVAIL 5Eh = CRYPTO DMA input done event, the correspondingg flag is CRYPTO:IRQSTAT.DMA_IN_DONE. Controlled by CRYPTO:IRQEN.DMA_IN_DONE 63h = Watchdog non maskable interrupt event, controlled by WDT:CTL.INTTYPE 64h = Software event 0, triggered by SWEV.SWEV0 65h = Software event 1, triggered by SWEV.SWEV1 66h = Software event 2, triggered by SWEV.SWEV2 67h = Software event 3, triggered by SWEV.SWEV3 68h = TRNG Interrupt event, controlled by TRNG:IRQEN.EN 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 74h = DMA sofware trigger from AUX, triggered by AUX_EVCTL:DMASWREQ.START 75h = DMA single request event from AUX, configured by AUX_EVCTL:DMACTL 76h = DMA burst request event from AUX, configured by AUX_EVCTL:DMACTL 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 78h = CPU halted 79h = Always asserted |
UDMACH15BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH15BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH15BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 15 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-7h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 7h | Read only selection value
7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting |
UDMACH16SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH16SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH16SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 16 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-2Dh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 2Dh | Read only selection value
2Dh = SSI1 RX DMA single request, controlled by SSI0:DMACR.RXDMAE |
UDMACH16BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH16BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH16BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 16 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-2Ch | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 2Ch | Read only selection value
2Ch = SSI1 RX DMA burst request , controlled by SSI0:DMACR.RXDMAE |
UDMACH17SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH17SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH17SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 17 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-2Fh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 2Fh | Read only selection value
2Fh = SSI1 TX DMA single request, controlled by SSI0:DMACR.TXDMAE |
UDMACH17BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH17BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH17BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 17 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-2Eh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 2Eh | Read only selection value
2Eh = SSI1 TX DMA burst request , controlled by SSI0:DMACR.TXDMAE |
UDMACH21SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH21SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH21SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 21 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-64h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 64h | Read only selection value
64h = Software event 0, triggered by SWEV.SWEV0 |
UDMACH21BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH21BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH21BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 21 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-64h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 64h | Read only selection value
64h = Software event 0, triggered by SWEV.SWEV0 |
UDMACH22SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH22SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH22SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 22 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-65h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 65h | Read only selection value
65h = Software event 1, triggered by SWEV.SWEV1 |
UDMACH22BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH22BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH22BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 22 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-65h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 65h | Read only selection value
65h = Software event 1, triggered by SWEV.SWEV1 |
UDMACH23SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH23SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH23SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 23 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-66h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 66h | Read only selection value
66h = Software event 2, triggered by SWEV.SWEV2 |
UDMACH23BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH23BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH23BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 23 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-66h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 66h | Read only selection value
66h = Software event 2, triggered by SWEV.SWEV2 |
UDMACH24SSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH24SSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH24SSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 24 SREQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-67h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 67h | Read only selection value
67h = Software event 3, triggered by SWEV.SWEV3 |
UDMACH24BSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH24BSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_UDMACH24BSEL_TABLE.
Return to the Summary Table.
Output Selection for DMA Channel 24 REQ
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-67h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 67h | Read only selection value
67h = Software event 3, triggered by SWEV.SWEV3 |
GPT3ACAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT3ACAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT3ACAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT3 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-5Bh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 5Bh | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 5Bh = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT6 wil be routed here. 5Ch = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT7 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
GPT3BCAPTSEL is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT3BCAPTSEL_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_GPT3BCAPTSEL_TABLE.
Return to the Summary Table.
Output Selection for GPT3 1
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-5Ch | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 5Ch | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 4h = Edge detect event from IOC. Configureded by the IOC:IOCFGn.EDGE_IRQ_EN and IOC:IOCFGn.EDGE_DET settings 5h = Combined event from battery monitor 6h = Combined event from Oscillator control 7h = Event from AON_RTC, controlled by the AON_RTC:CTL.COMB_EV_MASK setting 9h = Interrupt event from I2C Bh = AUX combined event, the corresponding flag register is here AUX_EVCTL:EVTOMCUFLAGS 15h = FLASH controller error event, the status flags are FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT 19h = RFC Doorbell Command Acknowledgement Interrupt, equvialent to RFC_DBELL:RFACKIFG.ACKFLAG 1Ah = Combined RFC hardware interrupt, corresponding flag is here RFC_DBELL:RFHWIFG 1Bh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE0 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_0 event 1Eh = Combined Interrupt for CPE Generated events. Corresponding flags are here RFC_DBELL:RFCPEIFG. Only interrupts selected with CPE1 in RFC_DBELL:RFCPEIFG can trigger a RFC_CPE_1 event 22h = SSI0 combined interrupt, interrupt flags are found here SSI0:MIS 23h = SSI1 combined interrupt, interrupt flags are found here SSI1:MIS 24h = UART0 combined interrupt, interrupt flags are found here UART0:MIS 25h = UART1 combined interrupt, interrupt flags are found here UART1:MIS 38h = AUX Timer2 event 0, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV0 39h = AUX Timer2 event 1, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV1 3Ah = AUX Timer2 event 2, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV2 3Bh = AUX Timer2 event 3, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_EV3 3Ch = AUX Timer2 pulse, corresponding to flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER2_PULSE 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 5Bh = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT6 wil be routed here. 5Ch = Port capture event from IOC, configured by IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM PORT_EVENT7 wil be routed here. 69h = AON wakeup event, the corresponding flag is here AUX_EVCTL:EVTOMCUFLAGS.AUX_WU_EV 6Ah = AUX Compare A event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA 6Bh = AUX Compare B event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB 6Ch = AUX TDC measurement done event, corresponds to the flag AUX_EVCTL:EVTOMCUFLAGS.AUX_TDC_DONE and the AUX_TDC status AUX_TDC:STAT.DONE 6Dh = AUX timer 0 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER0_EV 6Eh = AUX timer 1 event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_TIMER1_EV 6Fh = Autotake event from AUX semaphore, configured by AUX_SMPH:AUTOTAKE 70h = AUX ADC done, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_DONE 71h = AUX ADC FIFO watermark event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_FIFO_ALMOST_FULL 72h = Loopback of OBSMUX0 through AUX, corresponds to AUX_EVCTL:EVTOMCUFLAGS.MCU_OBSMUX0 73h = AUX ADC interrupt event, corresponds to AUX_EVCTL:EVTOMCUFLAGS.AUX_ADC_IRQ. Status flags are found here AUX_EVCTL:EVTOMCUFLAGS 77h = RTC periodic event controlled by AON_RTC:CTL.RTC_UPD_EN 79h = Always asserted |
AUXSEL0 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_AUXSEL0_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_AUXSEL0_TABLE.
Return to the Summary Table.
Output Selection for AUX Subscriber 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-10h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 10h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive Ch = GPT2A interrupt event, controlled by GPT2:TAMR Dh = GPT2B interrupt event, controlled by GPT2:TBMR Eh = GPT3A interrupt event, controlled by GPT3:TAMR Fh = GPT3B interrupt event, controlled by GPT3:TBMR 10h = GPT0A interrupt event, controlled by GPT0:TAMR 11h = GPT0B interrupt event, controlled by GPT0:TBMR 12h = GPT1A interrupt event, controlled by GPT1:TAMR 13h = GPT1B interrupt event, controlled by GPT1:TBMR 3Dh = GPT0A compare event. Configured by GPT0:TAMR.TCACT 3Eh = GPT0B compare event. Configured by GPT0:TBMR.TCACT 3Fh = GPT1A compare event. Configured by GPT1:TAMR.TCACT 40h = GPT1B compare event. Configured by GPT1:TBMR.TCACT 41h = GPT2A compare event. Configured by GPT2:TAMR.TCACT 42h = GPT2B compare event. Configured by GPT2:TBMR.TCACT 43h = GPT3A compare event. Configured by GPT3:TAMR.TCACT 44h = GPT3B compare event. Configured by GPT3:TBMR.TCACT 79h = Always asserted |
CM3NMISEL0 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CM3NMISEL0_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_CM3NMISEL0_TABLE.
Return to the Summary Table.
Output Selection for NMI Subscriber 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R-63h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R | 63h | Read only selection value
63h = Watchdog non maskable interrupt event, controlled by WDT:CTL.INTTYPE |
I2SSTMPSEL0 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_I2SSTMPSEL0_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_I2SSTMPSEL0_TABLE.
Return to the Summary Table.
Output Selection for I2S Subscriber 0
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-5Fh | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 5Fh | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 79h = Always asserted |
FRZSEL0 is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_FRZSEL0_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_FRZSEL0_TABLE.
Return to the Summary Table.
Output Selection for FRZ Subscriber
The halted debug signal is passed to peripherals such as the General Purpose Timer, Sensor Controller with Digital and Analog Peripherals (AUX), Radio, and RTC. When the system CPU halts, the connected peripherals that have freeze enabled also halt. The programmable output can be set to static values of 0 or 1, and can also be set to pass the halted signal.
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | EV | ||||||||||||||||||||||||||||||
R-0h | R/W-78h | ||||||||||||||||||||||||||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-7 | RESERVED | R | 0h | Reserved |
6-0 | EV | R/W | 78h | Read/write selection value Writing any other value than values defined by a ENUM may result in undefined behavior. 0h = Always inactive 78h = CPU halted 79h = Always asserted |
SWEV is shown in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_SWEV_FIGURE and described in #EVENT_FABRIC_EVENT_FABRIC_MAP1_EVENT_FABRIC_ALL_SWEV_TABLE.
Return to the Summary Table.
Set or Clear Software Events
31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 |
RESERVED | SWEV3 | ||||||
R-0h | R/W-0h | ||||||
23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 |
RESERVED | SWEV2 | ||||||
R-0h | R/W-0h | ||||||
15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
RESERVED | SWEV1 | ||||||
R-0h | R/W-0h | ||||||
7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
RESERVED | SWEV0 | ||||||
R-0h | R/W-0h | ||||||
Bit | Field | Type | Reset | Description |
---|---|---|---|---|
31-25 | RESERVED | R | 0h | Reserved |
24 | SWEV3 | R/W | 0h | Writing "1" to this bit when the value is "0" triggers the Software 3 event. |
23-17 | RESERVED | R | 0h | Reserved |
16 | SWEV2 | R/W | 0h | Writing "1" to this bit when the value is "0" triggers the Software 2 event. |
15-9 | RESERVED | R | 0h | Reserved |
8 | SWEV1 | R/W | 0h | Writing "1" to this bit when the value is "0" triggers the Software 1 event. |
7-1 | RESERVED | R | 0h | Reserved |
0 | SWEV0 | R/W | 0h | Writing "1" to this bit when the value is "0" triggers the Software 0 event. |