SWRA782 October   2023 CC1311P3 , CC1311R3 , CC1312PSIP , CC1312R , CC1312R7 , CC1314R10 , CC1352P , CC1352P7 , CC1352R , CC1354P10

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1Overview
    1. 1.1 Acronyms
    2. 1.2 Regulatory Compliance
      1. 1.2.1 TI 15.4 Stack
      2. 1.2.2 Regulatory Body
        1. 1.2.2.1 SUB 1
          1. 1.2.2.1.1 ETSI
          2. 1.2.2.1.2 ARIB
          3. 1.2.2.1.3 FCC
    3. 1.3 Polite Spectrum Access Timing Parameters
      1. 1.3.1 2.4 GHz
      2. 1.3.2 Coexistence
  5. 2Reference Examples
    1. 2.1 Available Chipsets
    2. 2.2 Flash and RAM Allocation
  6. 3Software Block Diagram
  7. 4Network Features
    1. 4.1 15.4 Supported PHYS
    2. 4.2 15.4 Device Architecture
    3. 4.3 15.4 Network Topology
      1. 4.3.1 Supported Network Modes
      2. 4.3.2 Beacon-Enabled Mode
      3. 4.3.3 Non Beacon-Enabled Mode
      4. 4.3.4 Frequency Hopping Mode
  8. 5Security
  9. 6Performance and Test Data
    1. 6.1 Test Data
    2. 6.2 Large Network Stability Tests
      1. 6.2.1 Sub1G
      2. 6.2.2 2.4 GHz
    3. 6.3 Transmission Rate
      1. 6.3.1 One Sensor Network
      2. 6.3.2 Five Sensor Network
      3. 6.3.3 47- Sensor Network
  10. 7Out-of-the Box-Experience
  11. 8Tools
    1. 8.1 Code Composer Studio
    2. 8.2 Sysconfig
    3. 8.3 Packet Sniffer
    4. 8.4 Battery Life Calculator
    5. 8.5 Linux

2.1 Available Chipsets

Table 2-1 shows that TI offers several Simplelink devices with a various amount of Flash and SRAM memory.

Table 2-1 Devices With a Various Amount of Flash and SRAM Memory
Device Flash (kB) SRAM (kb)
CC13x1x3 or CC26x1x3 352 40
CC13x2x1 or CC26x2x1 352 80
CC13x2x7 or CC26x2x7 704 144
CC13x4x10 or CC26x4x10 1024 256

With different system Cores:

  • For CC13x1 and CC26x1 devices the system core is Arm Cortex®-M4
  • For CC13x2 and CC26x2 devices the system core is Arm Cortex-M4F
  • For CC13x4 and CC2674 devices the system core is Arm Cortex-M33

In order to find the right chip, one should consider the amount of RAM and Flash that is required for our examples in different configurations. These values are estimated using examples from the Simplelink SDK. The memory allocation can be found in Table 2-2.

TI-SimpleLink devices with P-extension have in integrated Power Amplifier, which enable adaptable transmission power with up to 20 dbm.

These values are estimated using our examples and the maximum number of connected devices for a Coordinator set to 50. The values can be found in Table 2-2 as Flash or RAM in kB.