JAJU450D November   2015  – March 2020

 

  1.   改訂履歴

改訂履歴

Changes from C Revision (May 2019) to D Revision

  • Changed powerSUITE Page for the Grid Connected Inverter Solution imageGo
  • Changed Project Explorer View of Solution Project imageGo
  • Changed Current Loop Design Using Compensation Designer imageGo
  • Changed Compensation Designer With Measured Plant Frequency Response Data imageGo
  • Changed SPRUHZ5 to SPRUIK4 linkGo

Changes from B Revision (November 2017) to C Revision

  • Changed TMS310F280049M を TMS310F280049C にGo
  • Added TMS320F280049CGo
  • Changed ブロック図の TMS310F280049M を TMS320F280049C にGo
  • Deleted TMS310F280049M from block diagramGo
  • Changed TMS320F280049M to TMS320F280049CGo
  • Changed <sdk_install_path>\c2000ware\boards\controlcards\TMDSCNCD280049M to <sdk_install_path>\c2000ware\boards\controlcards\TMDSCNCD280049CGo
  • Changed TMS320F280049M to TMS320F280049CGo
  • Changed TMS320F280049M to TMS320F280049CGo

Changes from A Revision (October 2016) to B Revision

  • 現行のデザイン・ガイドのテンプレートに合わせてフォーマットを更新Go
  • Added 「リソース」に TMS320F280049M をGo
  • Added 「特長」に「TMS320F28377D および TMS320F280049M をサポート」をGo
  • Added ブロック図に TMS320F280049M をGo
  • Changed location of Excel sheet of calculationsGo
  • Changed location of info sheet in Section 3.1.1.2: Control Card SettingsGo
  • Added required settings for revision A of the TMS320F280049M control card in Section 3.1.1.2: Control Card SettingsGo
  • Added note in Section 3.1.2: Firmware: powerSUITE and Incremental Build SoftwareGo
  • Changed Step 5 in Section 3.1.2.1: Opening the Project Inside Code Composer Studio™Go
  • Updated Figure 21: Build Level 1 Control Diagram: Open Loop ProjectGo
  • Changed 1.26 VRMS to 1.26 IRMS in Step 13 in Section 3.1.2.3.1.5: Running the CodeGo
  • Updated Figure 26: Build Level 2 Control Diagram: Closed Current LoopGo
  • Changed location of the SFRA.exe file from controlSUITE/libs/app_libs/SFRA/<version>/GUI to <sdk_install_path>/libraries/sfra/GUIGo
  • Changed invloRefInst to invIoRef in Step 46 in Section 3.1.2.3.2.4: Running the CodeGo
  • Deleted the step "Set the clearInvTrip variable to 1 to clear the inverter trip" in Section 3.1.2.3.3.2: Running the CodeGo
  • Added the TMS320F28004x Piccolo™ Microcontrollers Technical Reference Manual to Section 6: Related DocumentationGo
  • Added the TMS320F28004x Piccolo™ Microcontrollers Data Sheet to Section 6: Related DocumentationGo

Changes from * Revision (November 2015) to A Revision

  • Added 「設計リソース」のTIEVM-HV-1PH-DCAC製品ページのリンクGo
  • Added configuration (CFG)Go
  • Added Figure 12: Control Scheme Used for Grid Connected Inverter ControlGo
  • Added note in Section 3: Getting Started With HardwareGo
  • Deleted "Keep in mind that the output capacitor is large (for example, 20 uF)." from Step 2 in Section 3.1: Base Board SettingsGo
  • Changed the control card slot from H5 to J15-J16Go
  • Changed isolated HV DC source connection from CON1 to J17Go
  • Changed Figure 16: Hardware Setup to Run Software for BUILD Level 1Go
  • Added Section 3.3: Tips to Connect JTAG USB CableGo
  • Added Section 4.1.2: Open TI Design Software for AdaptationGo
  • Added "up to 50 V" to Step 9 under Running the CodeGo
  • Added "Now raise the DC Bus voltage slowly up to 380 V" to Step 10 under Running the CodeGo
  • Deleted "Check the frequency of the generated AC waveform." from Running the CodeGo
  • Deleted "Confirm that the generated AC waveform matches the value entered on the powerSUITE page (for example, 60 Hz)." from Running the CodeGo
  • Changed variable from sine_mains.SigFreq to guiFreqAvgGo
  • Changed output voltage from 133 VRMS to 126 VRMSGo
  • Changed current from 1.35 VRMS to 1.26 VRMSGo
  • Changed numeration after Figure 25: BUILD LEVEL 1 Graph1.GraphProp File Showing Measured Per-Unit Voltage and Current ValuesGo
  • Added Figure 27: Hardware Setup to Run Software for Build Level 2: DC CheckGo
  • Deleted "Turn the S1 switch to the ON position."Go
  • Added note under Running the CodeGo
  • Changed title in Figure 32 from "Setup for DC Check of the Current Controller" to "Hardware Setup to Run Software for BUILD Level 2: AC Check"Go
  • Added note after Step 8 in Running the CodeGo
  • Changed Steps 2 through 9 under Running the CodeGo
  • Deleted Steps 10 through 13 under Running the CodeGo
  • Changed Step 16 under Running the CodeGo