SBAU378A September   2021  – January 2022 ADS1148 , ADS1248

 

  1.   Trademarks
  2. 1Introduction
  3. 2Getting Started With the ADS1x48EVM
  4. 3ADS1x48EVM Overview
    1. 3.1 Analog and Digital Power Supplies
    2. 3.2 Voltage Reference Options
    3. 3.3 Clock Options
    4. 3.4 Digital Interface
    5. 3.5 Analog Input Connections
      1. 3.5.1 Connecting a Thermocouple to J5 on the ADS1x48EVM
      2. 3.5.2 Connecting a Thermistor to J5 on the ADS1x48EVM
        1. 3.5.2.1 Using Thermistor RT1 for Thermocouple Cold Junction Compensation
      3. 3.5.3 Connecting an RTD to J6 on the ADS1x48EVM
        1. 3.5.3.1 Connecting a 2-Wire RTD Using a Low-Side RREF to J6 on the ADS1x48EVM
        2. 3.5.3.2 Connecting a 2-Wire RTD Using a High-Side RREF to J6 on the ADS1x48EVM
        3. 3.5.3.3 Connecting a 3-Wire RTD Using One IDAC and a Low-Side RREF to J6 on the ADS1x48EVM
        4. 3.5.3.4 Connecting a 3-Wire RTD Using One IDAC and a High-Side RREF to J6 on the ADS1x48EVM
        5. 3.5.3.5 Connecting a 3-Wire RTD Using Two IDACs and a Low-Side RREF to J6 on the ADS1x48EVM
        6. 3.5.3.6 Connecting a 3-Wire RTD Using Two IDACs and a High-Side RREF to J6 on the ADS1x48EVM
        7. 3.5.3.7 Connecting a 4-Wire RTD Using a Low-Side RREF to J6 on the ADS1x48EVM
        8. 3.5.3.8 Connecting a 4-Wire RTD Using a High-Side RREF to J6 on the ADS1x48EVM
        9. 3.5.3.9 Summary of ADS1x48EVM RTD Configuration Settings
      4. 3.5.4 Connecting a General-Purpose Input to J5 on the ADS1x48EVM
  5. 4ADS1x48EVM GUI
    1. 4.1 Home
      1. 4.1.1 Menu Bar
        1. 4.1.1.1 File Menu
        2. 4.1.1.2 Options Menu
        3. 4.1.1.3 Tools Menu
        4. 4.1.1.4 Help Menu
    2. 4.2 Data Capture
      1. 4.2.1 Time Domain and Histogram Statistics
      2. 4.2.2 Time Domain Plot
      3. 4.2.3 Histogram Plot
      4. 4.2.4 FFT Statistics and Plot
    3. 4.3 Register Map
      1. 4.3.1 Register Read and Write Options
        1. 4.3.1.1 Read Register Options
        2. 4.3.1.2 Write Register Options
  6. 5Bill of Materials, Printed Circuit Board Layout, and Schematic
    1. 5.1 Bill of Materials
    2. 5.2 Printed Circuit Board Layout
    3. 5.3 Schematic
  7. 6Revision History

4.1.1.1 File Menu

The File drop-down menu displays the available options shown in Figure 4-4. These options include:

  • Program Device: Only necessary if an important firmware change is required
  • Analysis Data:
    • Save data: Save the Analysis Data to a comma-separated values (CSV) formatted file for further analysis using external programs
    • Load data: Loads a saved data file back into the GUI for further review or analysis
  • Register Data
    • Save register: Save the register data for a specific configuration
    • Load register: Load a previously saved register map configuration
GUID-20210728-CA0I-CLWN-PDSC-JFQZT7S4VVMS-low.pngFigure 4-4 File Menu