SBAU395 april   2023 DAC39RF10

 

  1.   Introduction
  2. 1Trademarks
  3. 2Required Equipment
  4. 3Setup Procedure
    1. 3.1  Installing the High Speed Data Converter (HSDC) Pro Software
    2. 3.2  Installing the DAC39RF10EVM Configuration GUI Software
    3. 3.3  Connect the DAC39RF10EVM and TSW14J59EVM
    4. 3.4  Connect the Power Supplies to the Boards (Power Off)
    5. 3.5  Connect the Spectrum Analyzer to the EVM
    6. 3.6  Turn On the TSW14J59EVM Power and Connect to the PC
    7. 3.7  Turn On the DAC39RF10EVM Power Supplies and Connect to the PC
    8. 3.8  Turn On the Signal Generator RF Outputs
    9. 3.9  Launch the DAC39RF10EVM GUI and Program the DAC EVM
    10. 3.10 Programming the NCO
      1. 3.10.1 SPIDAC( NCO only) Operation
    11. 3.11 Launch the HSDCpro Software and Load the FPGA Image to the TSW14J59EVM
  5. 4Device Configuration
    1. 4.1 Supported JESD204C Device Features
    2. 4.2 Tab Organization
    3. 4.3 Register Map and Console Control
  6. 5Troubleshooting the DAC39RF10EVM
  7. 6References
    1. 6.1 Technical Reference Documents
    2. 6.2 TSW14J59EVM Operation
  8. 7Appendix
    1. 7.1 Customizing the EVM for Optional Clocking Support
      1. 7.1.1 LMX->DACCLK | LMX/LMK-> FPGA option (Default)
      2. 7.1.2 EXT->DACCLK | LMX/LMK-> FPGA Clocking Option
      3. 7.1.3 EXT->DACCLK | LMK-> FPGA Clocking Option
    2. 7.2 Signal Routing
    3. 7.3 Analog Outputs
    4. 7.4 Jumpers and LEDs

7.2 Signal Routing

Table 7-1 provides the signal routing details for the DAC39RF10EVM.

Table 7-1 DAC39RF10EVM Signal Routing
JESD204C

Inputs

 FMC(+) Pi FMC(+) Signal Names(1)
Lane0 A38,A39 DP5_C2M_INV
Lane1 B36,B37 DP6_C2M_INV
Lane2 B32,B33 DP7_C2M_INV
Lane3 A34,A35 DP4_C2M_INV
Lane4 Y30,Y31 DP13_C2M_INV
Lane5 A30,A31 DP3_C2M_INV
Lane6 Z28,Z29 DP12_C2M_INV
Lane7 B28,B29 DP8_C2M_INV
Lane8 Y6,Y7 DP21_C2M_INV
Lane9 C2,C3 DP0_C2M_INV
Lane10 Z8,Z9 DP20_C2M_INV
Lane11 A22,A23 DP1_C2M_INV

Lane12

 Z24,Z25 DP10_C2M_INV
Lane13 B25,B26 DP9_C2M_INV
Lane14 Y26,Y27 DP11_C2M_INV
Lane15 A26,A27 DP2_C2M_INV
(1) Red items with _INV in the signal name are inverted with respect to standard FMC polarity.