All trademarks are the property of their respective owners.
Analog multiplexers are used in electronic systems to control a specific transmission path for an analog signal. These devices are used in a wide variety of applications, such as USB3, PCIe and HDMI system.
There can possible be a situation where the desired number of input channels are not available in multiplexers of a particular system. Cascading refers to a process where large multiplexers can be designed and implemented using smaller multiplexers. For instance, 8:1 Multiplexers can be designed using three 4:1 Multiplexers and similarly it can be designed using seven 2:1 multiplexer as shown in the below Figure 1-1.
One of the major parameters of analog multiplexers is On resistance. On-resistance (RON) is the resistance of the multiplexers path between the drain and source terminal when the multiplexer is closed. Ideally, RON needs to be kept as low as possible in order to keep the signal loss and propagation delays to be small. The On resistance value of the multiplexer translates into multiple performance characteristics of a signal multiplexer. For example, RON impacts the multiplexer’s power consumption, propagation delay, and the bandwidth of the signals that can pass through the multiplexer without distortion. In most cases, lower RON values are preferred in order to achieve optimal design.
An analog multiplexer also has many ac specifications, such as bandwidth and insertion loss. Bandwidth is an important parameter to characterize the performance of many electrical systems. The term bandwidth refers to the pass band width of a filter, and in the case of a low-pass filter, the bandwidth is equal to the –3 dB frequency and indicates the upper limit of the frequency of signals passing through the multiplexers. Understanding the bandwidth capability of a signal multiplexer helps to determine if a multiplexer meets the performance requirements of the target application. A good rule of thumb is BW should be greater than or equal to 1.5 or 2 times Nyquist frequency.
Other important AC parameters are insertion loss and return loss. At high frequency, signal loss produces signal attenuation and distortion; the signal will be attenuated by conductor resistance and leakage in the material. The design of high-speed circuits therefore requires a knowledge of not only BW and Ron resistor, but also the dielectric constant and loss parameter.
Insertion loss and return loss are widely used terms in the field of microwave technologies. They play an important role in designing and development of high-speed devices such as filters, multiplexers. Insertion loss and return loss are what is used in cascading multiplexer’s analysis.
So what are Insertion loss and return loss? Technically, when some system or circuit is inserted between a source and a load, some of the signal power from the source is dissipated through the circuit components due to their resistive nature that results in losses. Therefore, not all the transmitted signal power is transferred to the load. The losses between the incident power and the transmitted power is called insertion Loss. Likewise, the difference between the incident power and the reflected power is called return loss.
Insertion loss and return loss are linked with the scattering perimeters when the source and the load of the system is matched to the same reference impedance (say 50 Ohms). S parameters are the modern way of analyzing N-port networks. It is very helpful in optimizing the circuit to its best. It is capable of determining even smaller return loss and insertion loss in the form of s-parameters namely S11, S22, S12, S21:
S12 = forward transmission coefficient
S21 = reverse transmission coefficient
S11 = input reflection coefficient
S22 = output reflection coefficient
Figure 3-3 is the eye diagram of the 10-Gbps input signal, Figure 3-4 is the output eye diagram from the first multiplexer, Figure 3-5 is the output eye diagram from second multiplexer. From Figure 3-5, we can see waveform is degraded after two cascading multiplexers.
Last, let’s look at the real scope measurement and see how they correlate with the simulation result. Figure 3-6 is the waveform of the 10Gbps input signal, Figure 3-7 is the output waveform from the first multiplexer, Figure 3-8 is the output waveform form the second multiplexer. From Figure 3-7 and Figure 3-8, real measurement is correlated well with simulation result.
In this technical article, an analysis method with s-parameter model for cascading multiplexers is presented. Test results for both simulation and lab measurement are correlated. For high speed system with cascading multiplexers, other than looking at Ron and bandwidth, it’s still necessary to look at insertion loss and return loss parameter at particular frequency interested before make decision to choose the right multiplexers.
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. |
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. |
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. |
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated |