SLAS778C February   2013  – September 2021 TAS2505

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  I2S/LJF/RJF Timing in Master Mode
    7. 6.7  I2S/LJF/RJF Timing in Slave Mode
    8. 6.8  DSP Timing in Master Mode
    9. 6.9  DSP Timing in Slave Mode
    10. 6.10 I2C Interface Timing
    11. 6.11 SPI Interface Timing
    12. 6.12 Typical Characteristics
      1. 6.12.1 Class D Speaker Driver Performance
      2. 6.12.2 HP Driver Performance
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Audio Analog I/O
      2. 7.3.2 Audio DAC and Audio Analog Outputs
      3. 7.3.3 DAC
      4. 7.3.4 POR
      5. 7.3.5 CLOCK Generation and PLL
    4. 7.4 Device Functional Modes
      1. 7.4.1 Digital Pins
      2. 7.4.2 Analog Pins
      3. 7.4.3 Multifunction Pins
      4. 7.4.4 Analog Signals
        1. 7.4.4.1 Analog Inputs AINL and AINR
      5. 7.4.5 DAC Processing Blocks — Overview
      6. 7.4.6 Digital Mixing and Routing
      7. 7.4.7 Analog Audio Routing
      8. 7.4.8 Digital Audio and Control Interface
        1. 7.4.8.1 Digital Audio Interface
        2. 7.4.8.2 Control Interface
          1. 7.4.8.2.1 I2C Control Mode
          2. 7.4.8.2.2 SPI Digital Interface
        3. 7.4.8.3 Device Special Functions
    5. 7.5 Register Map
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Typical Configuration
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Community Resources
    4. 11.4 Trademarks
  12. 12Mechanical, Packaging, and Orderable Information

7.4.8.1 Digital Audio Interface

Audio data is transferred between the host processor and the TAS2505 via the digital audio data serial interface, or audio bus. The audio bus on this device is flexible, including left- or right-justified data options, support for I2S or PCM protocols, programmable data-length options, a TDM mode for multichannel operation, flexible master or slave configurability for each bus clock line, and the ability to communicate with multiple devices within a system directly.

The audio bus of the TAS2505 can be configured for left- or right-justified, I2S, DSP, or TDM modes of operation, where communication with standard telephony PCM interfaces is supported within the TDM mode. These modes are all MSB-first, with data width programmable as 16, 20, 24, or 32 bits by configuring page 0, register 27, bits D5–D4. In addition, the word clock and bit clock can be independently configured in either master or slave mode for flexible connectivity to a wide variety of processors. The word clock is used to define the beginning of a frame, and may be programmed as either a pulse or a square-wave signal. The frequency of this clock corresponds to the maximum of the selected DAC sampling frequencies.

For more detailed information see the TAS2505 Application Reference Guide (SLAU472).