| 31-14 |
RESERVED |
R |
0x0 |
|
| 13 |
PROGMISC |
R/W1C |
0x0 |
PROGVER Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that an interrupt has not occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled.Writing a 1 to this bit clears PROGMISC and also the PROGRIS bit in the FCRIS register (see ).
|
| 12 |
RESERVED |
R |
0x0 |
|
| 11 |
ERMISC |
R/W1C |
0x0 |
ERVER Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that an interrupt has not occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled.Writing a 1 to this bit clears ERMISC and also the ERRIS bit in the FCRIS register (see ).
|
| 10 |
INVDMISC |
R/W1C |
0x0 |
Invalid Data Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that an interrupt has not occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled.Writing a 1 to this bit clears INVDMISC and also the INVDRIS bit in the FCRIS register (see ).
|
| 9 |
VOLTMISC |
R/W1C |
0x0 |
VOLT Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that an interrupt has not occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled.Writing a 1 to this bit clears VOLTMISC and also the VOLTRIS bit in the FCRIS register (see ).
|
| 8-3 |
RESERVED |
R |
0x0 |
|
| 2 |
EMISC |
R/W1C |
0x0 |
EEPROM Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that an interrupt has not occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled.Writing a 1 to this bit clears EMISC and also the ERIS bit in the FCRIS register (see ).
|
| 1 |
PMISC |
R/W1C |
0x0 |
Programming Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that a programming cycle complete interrupt has not occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled because a programming cycle completed.Writing a 1 to this bit clears PMISC and also the PRIS bit in the FCRIS register (see ).
|
| 0 |
AMISC |
R/W1C |
0x0 |
Access Masked Interrupt Status and Clear
0x0 = When read, a 0 indicates that no improper accesses have occurred.A write of 0 has no effect on the state of this bit.
0x1 = When read, a 1 indicates that an unmasked interrupt was signaled because a program or erase action was attempted on a block of Flash memory that contradicts the protection policy for that block as set in the FMPPEn registers.Writing a 1 to this bit clears AMISC and also the ARIS bit in the FCRIS register (see ).
|