SLAU869E October   2022  – January 2024

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1Getting Started
    1. 1.1 Introduction
    2. 1.2 Key Features
    3. 1.3 What's Included
      1. 1.3.1 Kit Contents
      2. 1.3.2 Software Examples
    4. 1.4 First Step Out-of-Box Experience
      1. 1.4.1 Connecting to the Computer
      2. 1.4.2 Running the Out-of-Box Experience
    5. 1.5 Next Steps: Looking Into the Provided Code
  5. 2Hardware
    1. 2.1 Jumper Map
    2. 2.2 Block Diagram
    3. 2.3 Hardware Features
      1. 2.3.1 MSPM0L1306 MCU
      2. 2.3.2 XDS110-ET Onboard Debug Probe With EnergyTrace Technology
      3. 2.3.3 Debug Probe Connection: Isolation Jumper Block
      4. 2.3.4 Application (or Backchannel) UART
      5. 2.3.5 Using an External Debug Probe Instead of the Onboard XDS110-ET
      6. 2.3.6 Using the XDS110-ET Debug Probe With a Different Target
      7. 2.3.7 Special Features
        1. 2.3.7.1 Thermistor
        2. 2.3.7.2 Light Sensor
    4. 2.4 Power
      1. 2.4.1 XDS110-ET USB Power
    5. 2.5 External Power Supply and BoosterPack Plug-in Module
    6. 2.6 Measure Current Draw of the MSPM0 MCU
    7. 2.7 Clocking
    8. 2.8 BoosterPack Plug-in Module Pinout
  6. 3Software Examples
  7. 4Resources
    1. 4.1 Integrated Development Environments
      1. 4.1.1 TI Cloud Development Tools
      2. 4.1.2 TI Resource Explorer Cloud
      3. 4.1.3 Code Composer Studio Cloud
      4. 4.1.4 Code Composer Studio IDE
    2. 4.2 MSPM0 SDK and TI Resource Explorer
    3. 4.3 MSPM0L1306 MCU
      1. 4.3.1 Device Documentation
      2. 4.3.2 MSPM0L1306 Code Examples
    4. 4.4 Community Resources
      1. 4.4.1 TI E2E Forums
  8. 5Schematics
  9. 6Revision History

2.1 Jumper Map

Table 2-1 LaunchPad Kit Jumpers Shunt Installation
Jumper Description Default setting Connected Pin or Signal Low Power Measurement Recommendation
J101 XDS110-ET isolation block Installed GND, 5 V, 3V3, RXD, TXD, NRST, SWDIO, SWCLK, BSL OFF to disconnect from XDS-110 circuitry
J102 XDS110-ET Program Out NA GND, 3V3, SWDIO, SWCLK, NRST No external connection
J103 XDS110-ET Program In NA GND, 3V3, SWDIO, SWCLK No external connection
J1 Thermistor signal selection (1) short to (2) PA15 (ADC0_9) OFF to disconnect from thermistor circuit
J2 Red LED D2 Installed PA0 OFF to disconnect pin from LED
J3 RGB LED D1 – Green Channel Installed PA13 (TIMG0_C1) OFF to disconnect pin from RGB LED
J4 Light Sensor Installed PA25 (OPA0_IN+) OFF to disconnect from photodiode circuit
J5 Light Sensor Installed PA24 (OPA0_IN-) OFF to disconnect from photodiode circuit
J6 Light Sensor Installed PA22 (OPA0_OUT) OFF to disconnect from photodiode circuit
J7 External 3.3V NA 3V3, GND No connect to external circuits
J8 External 5V NA 5V, GND No connect to external circuits
J9 Open-drain IO PA0 voltage pullup selection (2) open NA OFF if pin initialized as output low or input with pullup or pulldown
J10 Open-drain IO PA1 voltage pullup selection (2) open NA OFF if pin initialized as output low or input with pullup or pulldown
J11 Button S1 connection Installed PA18 OFF to avoid current from external pulldown depending on pin configuration
J12 RGB LED D1 – Red Channel Installed PA26 (TIMG1_C0) OFF to disconnect pin from RGB LED
J13 RGB LED D1 – Blue Channel Installed PA27 (TIMG1_C1) OFF to disconnect pin from RGB LED
J14 Alternate PA11 BoosterPack Connection (1) short to (2) PA11 – SW1 Don't care if not used in BoosterPack connector
J15 Thermistor Power Installed 3V3 OFF to remove power to thermistor circuitry
J16 UART Path Selection – BP – UART TX- XDS (1) short to (2) PA8 – XDS OFF to disconnect pin
J17 UART Path Selection – BP – UART RX- XDS (1) short to (2) PA9 – XDS OFF to disconnect pin