SLLS373M July   1999  – March 2024 SN65LVDS1 , SN65LVDS2 , SN65LVDT2

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Options
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Driver Electrical Characteristics
    6. 6.6 Receiver Electrical Characteristics
    7. 6.7 Driver Switching Characteristics
    8. 6.8 Receiver Switching Characteristics
    9. 6.9 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 SN65LVDS1 Features
        1. 8.3.1.1 Driver Output Voltage and Power-On Reset
        2. 8.3.1.2 Driver Offset
        3. 8.3.1.3 5-V Input Tolerance
        4. 8.3.1.4 NC Pins
        5. 8.3.1.5 Driver Equivalent Schematics
      2. 8.3.2 SN65LVDS2 and SN65LVDT2 Features
        1. 8.3.2.1 Receiver Open Circuit Fail-Safe
        2. 8.3.2.2 Receiver Output Voltage and Power-On Reset
        3. 8.3.2.3 Common-Mode Range vs Supply Voltage
        4. 8.3.2.4 General Purpose Comparator
        5. 8.3.2.5 Receiver Equivalent Schematics
        6. 8.3.2.6 NC Pins
    4. 8.4 Device Functional Modes
      1. 8.4.1 Operation With VCC < 1.5 V
      2. 8.4.2 Operation With 1.5 V ≤ VCC < 2.4 V
      3. 8.4.3 Operation With 2.4 V ≤ VCC < 3.6 V
      4. 8.4.4 SN65LVDS1 Truth Table
      5. 8.4.5 SN65LVDS2 and SN65LVDT2 Truth Table
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Point-to-Point Communications
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1  Driver Supply Voltage
          2. 9.2.1.2.2  Driver Bypass Capacitance
          3. 9.2.1.2.3  Driver Input Voltage
          4. 9.2.1.2.4  Driver Output Voltage
          5. 9.2.1.2.5  Interconnecting Media
          6. 9.2.1.2.6  PCB Transmission Lines
          7. 9.2.1.2.7  Termination Resistor
          8. 9.2.1.2.8  Driver NC Pins
          9. 9.2.1.2.9  Receiver Supply Voltage
          10. 9.2.1.2.10 Receiver Bypass Capacitance
          11. 9.2.1.2.11 Receiver Input Common-Mode Range
          12. 9.2.1.2.12 Receiver Input Signal
          13. 9.2.1.2.13 Receiver Output Signal
          14. 9.2.1.2.14 Receiver NC Pins
      2. 9.2.2 Application Curve
      3. 9.2.3 Multidrop Communications
        1. 9.2.3.1 Design Requirements
        2. 9.2.3.2 Detailed Design Procedure
          1. 9.2.3.2.1 Interconnecting Media
        3. 9.2.3.3 Application Curve
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Microstrip vs. Stripline Topologies
      2. 11.1.2 Dielectric Type and Board Construction
      3. 11.1.3 Recommended Stack Layout
      4. 11.1.4 Separation Between Traces
      5. 11.1.5 Crosstalk and Ground Bounce Minimization
      6. 11.1.6 Decoupling
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Other LVDS Products
    2. 12.2 Third-Party Products Disclaimer
    3. 12.3 Documentation Support
      1. 12.3.1 Related Information
    4. 12.4 Receiving Notification of Documentation Updates
    5. 12.5 Support Resources
    6. 12.6 Trademarks
    7. 12.7 Electrostatic Discharge Caution
    8. 12.8 Glossary
  14. 13Revision History
  15. 14Mechanical, Packaging, and Orderable Information

1 Features

  • Meets or Exceeds the ANSI TIA/EIA-644 Standard
  • Designed for Signaling Rates (1) up to:
    • 630Mbps for Drivers
    • 400Mbps for Receivers
  • Operates From a 2.4V to 3.6V Supply
  • Available in SOT-23 and SOIC Packages
  • Bus-Terminal ESD Exceeds 9kV
  • Low-Voltage Differential Signaling With Typical Output Voltages of 350mV Into a 100Ω Load
  • Propagation Delay Times
    • 1.7ns Typical Driver
    • 2.5ns Typical Receiver
  • Power Dissipation at 200MHz
    • 25mW Typical Driver
    • 60mW Typical Receiver
  • LVDT Receiver Includes Line Termination
  • Low Voltage TTL (LVTTL) Level Driver Input Is 5V Tolerant
  • Driver Is Output High-Impedance with
    VCC < 1.5V
  • Receiver Output and Inputs are High-Impedance With VCC < 1.5V
  • Receiver Open-Circuit Fail Safe
  • Differential Input Voltage Threshold Less Than 100mV
1. The signaling rate of a line, is the number of voltage transitions that are made per second expressed in the units bps (bits per second)