SLLU387 August   2024

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   Applications
  6.   6
  7. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
    4. 1.4 Device Information
  8. 2Hardware
    1. 2.1 Quick Start Guide
    2. 2.2 Hardware Setup
    3. 2.3 Hardware Connections Overview – MCF8315RRYEVM
    4. 2.4 Connection Details
    5. 2.5 MSP430FR2355 Microcontroller
    6. 2.6 LED Lights
    7. 2.7 User-Configurable Settings
  9. 3Software
    1. 3.1 Firmware and GUI Application
    2. 3.2 Downloading and Running Motor Studio
    3. 3.3 Downloading Code Composer Studio and Importing GUI Firmware Code
    4. 3.4 Using eZ-FET to Program the Onboard MSP430FR2355
  10. 4Hardware Design Files
    1. 4.1 Schematics
      1. 4.1.1 Main Supply and Pi Filter
      2. 4.1.2 Connectors and Interface
      3. 4.1.3 USB to UART
      4. 4.1.4 MCU Programming and Debug
      5. 4.1.5 MSP430FR2355 MCU
      6. 4.1.6 MCF8315 3-Phase Sensorless FOC Integrated Driver
      7. 4.1.7 Buck Regulator
      8. 4.1.8 Status LEDs
      9. 4.1.9 Switches and Speed Input
    2. 4.2 PCB Layouts
    3. 4.3 Bill of Materials (BOM)
  11. 5Additional Information
    1. 5.1 Trademarks

2.7 User-Configurable Settings

The MCF8315RRYEVM includes a variety of user-selectable jumpers, switches, and resistors on the entirety of the evaluation board to configure settings. Table 2-2 summarizes all of these configurable settings.

Table 2-2 Description of User-Selectable Settings on MCF8315RRYEVM (Default in Bold)
Designator Setting Name Description Layer Position Function
L1/L2/R14 Buck Regulator mode User populates L1, L2, or R14 to choose switching component for buck regulator Top L1 = 47uH Inductor Inductor Mode
Bottom L2 = 22μH Inductor Mode
Bottom R14 = 22Ω Resistor Mode
J5 3V3_SEL Select 3.3V for MCU power Top J5 = 3V3EXT External
J5 = 3V3COM From FTDI (30mA)
J3 5V_SEL Select 5V for FTDI power Top J3 = 5V_EXT External
J3 = 5V_USB From USB power (500mA)
J1 SPEED_SEL Selects SPEED input source Top J1 = EXT External EXT_SPEED test point
J1 = POT From Potentiometer R4
J1 = PWM

On-board PWM from MSP430
J6 MSP to MCx Shunt jumper bridge Connects signals from MCU and user switches to MCx8315 when jumpers are inserted Top DRVOFF_SW DRVOFF
DIR_SW DIR
BRAKE_SW BRAKE
SPEED_IN SPEED
MSP_SOMI/SCL

SCL
MSP_SIMO/SDA SDA

MSP_CLK

NC
MSP_STE

NC
MSP_A3

DACOUT
MSP_A2

NC

MSP_A1

NC

MSP_ALARM

ALARM

MSP_nFAULT

nFAULT

MSP_FGOUT

FGOUT

NC

VBK

AGND

PGND

S1

 BRAKE Turns on all low-side MOSFETs Top Left Brake enabled
Right Brake disabled
S2 DIR Controls direction of motor Top Left ABC

Right

 ACB
S3 DRVOFF Disables gate drivers Top Left MCF8315 FETs disabled
Right MCF8315 FETs enabled