SLUS724F September   2006  – January 2022 BQ2022A

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics: DC
    6. 6.6 Switching Characteristics: AC
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 1024-Bit EPROM
      2. 7.3.2 EPROM Status Memory
      3. 7.3.3 Error Checking
      4. 7.3.4 Customizing the BQ2022A
      5. 7.3.5 Bus Termination
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
      1. 7.5.1  Serial Communication
      2. 7.5.2  Initialization
      3. 7.5.3  ROM Commands
        1. 7.5.3.1 READ ROM Command
        2. 7.5.3.2 SKIP ROM Command
      4. 7.5.4  Memory/Status Function Commands
      5. 7.5.5  READ MEMORY Commands
        1. 7.5.5.1 READ MEMORY/Page CRC
        2. 7.5.5.2 READ MEMORY/Field CRC
      6. 7.5.6  WRITE MEMORY Command
      7. 7.5.7  READ STATUS Command
      8. 7.5.8  WRITE STATUS Command
      9. 7.5.9  PROGRAM PROFILE Byte
      10. 7.5.10 SDQ Signaling
      11. 7.5.11 RESET and PRESENCE PULSE
      12. 7.5.12 WRITE Bit
      13. 7.5.13 READ Bit
      14. 7.5.14 PROGRAM PULSE
      15. 7.5.15 IDLE
      16. 7.5.16 CRC Generation
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Programming Circuit Example
        2. 8.2.2.2 SDQ Master Best Practices
      3. 8.2.3 Application Curve
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
      2. 11.2.2 Receiving Notification of Documentation Updates
    3. 11.3 Trademarks
    4. 11.4 Support Resources
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

8.2.2.1 Programming Circuit Example

The BQ2022A requires a 12-V maximum pulse signal to program the OTP memory. It is necessary to have a programming test setup for production. Figure 8-2 shows an example of what the circuit could be for such setup. The Programming Module contains the microcontroller that acts as SDQ master and also controls the time of the programming pulse and its width. The 12-V supply is the source for the programming pulse. Only SDQ and VSS signals need to exit the test setup as the Application Circuit containing the BQ2022A under test is connected only for programming and verifying data.

The Programming Module typically will connect to a PC using interface such as USB. The diagram in Figure 8-2 does not include the interface to a PC which can vary depending on the system designer's choice.

GUID-B9ED3544-6FAE-41C4-A68B-A997A3F94979-low.gif Figure 8-2 BQ2022A Programming Circuit Example