SLUSFB5 June   2024 BQ41Z50

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Description (continued)
  6. 5 Pin Configuration and Functions
    1. 5.1 Pin Equivalent Diagrams
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Supply Current
    6. 6.6  Power Supply Control
    7. 6.7  Current Wake Detector
    8. 6.8  VC0, VC1, VC2, VC3, VC4, PACK
    9. 6.9  SMBD, SMBC
    10. 6.10 PRES/SHUTDN, DISP
    11. 6.11 ALERT
    12. 6.12 Coulomb Counter Digital Filter (CC1)
    13. 6.13 ADC Digital Filter
    14. 6.14 CHG, DSG High-side NFET Drivers
    15. 6.15 Precharge (PCHG) FET Drive
    16. 6.16 FUSE Drive
    17. 6.17 Internal Temperature Sensor
    18. 6.18 TS1, TS2, TS3, TS4
    19. 6.19 Flash Memory
    20. 6.20 GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, GPIO7
    21. 6.21 Elliptical Curve Cryptography (ECC)
    22. 6.22 SMBus Interface Timing
    23. 6.23 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Primary (1st Level) Safety Features
      2. 7.3.2 Secondary (2nd Level) Safety Features
      3. 7.3.3 Charge Control Features
      4. 7.3.4 Gas Gauging
      5. 7.3.5 Lifetime Data Logging Features
      6. 7.3.6 Authentication
      7. 7.3.7 Configuration
        1. 7.3.7.1 Oscillator Function
        2. 7.3.7.2 Real Time Clock
        3. 7.3.7.3 System Present Operation
        4. 7.3.7.4 Emergency Shutdown
        5. 7.3.7.5 2-Series, 3-Series, or 4-Series Cell Configuration
        6. 7.3.7.6 Cell Balancing
        7. 7.3.7.7 LED Display
      8. 7.3.8 Battery Parameter Measurements
        1. 7.3.8.1 Charge and Discharge Counting
        2. 7.3.8.2 Voltage
        3. 7.3.8.3 Current
        4. 7.3.8.4 Temperature
        5. 7.3.8.5 Communications
          1. 7.3.8.5.1 SMBus On and Off State
    4. 7.4 Device Functional Modes
  9. 8 Applications and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 High-Current Path
          1. 8.2.2.1.1 Protection FETs
          2. 8.2.2.1.2 Chemical Fuse
          3. 8.2.2.1.3 Lithium-Ion Cell Connections
          4. 8.2.2.1.4 Sense Resistor
          5. 8.2.2.1.5 ESD Mitigation
        2. 8.2.2.2 Gas Gauge Circuit
          1. 8.2.2.2.1 Coulomb-Counting Interface
          2. 8.2.2.2.2 Low-dropout Regulators (LDOs)
            1. 8.2.2.2.2.1 REG18
            2. 8.2.2.2.2.2 REG135
          3. 8.2.2.2.3 System Present
          4. 8.2.2.2.4 SMBus Communication
          5. 8.2.2.2.5 FUSE Circuitry
        3. 8.2.2.3 Secondary-Current Protection
          1. 8.2.2.3.1 Cell and Battery Inputs
          2. 8.2.2.3.2 External Cell Balancing
          3. 8.2.2.3.3 PACK and FET Control
          4. 8.2.2.3.4 Temperature Measurement
          5. 8.2.2.3.5 LEDs
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
        1. 8.4.1.1 Protector FET Bypass and Pack Terminal Bypass Capacitors
        2. 8.4.1.2 ESD Spark Gap
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.18 TS1, TS2, TS3, TS4

Typical values stated where TA = 25°C and VBAT = 14.4V, Min/Max values stated where TA = –40°C to 85°C and VBAT = 3.0V to 28V (unless otherwise noted)
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
VINInput voltage rangeTS1, TS2, TS3, TS4, VBIAS = VREF1–0.20.8 × VREF1V
TS1, TS2, TS3, TS4, VBIAS = VREG–0.20.8 × VREG
RNTC_PUInternal pull-up resistanceTS1, TS2, TS3, TS4, Setting for nominal 18kΩ14.41821.6kΩ
RNTC_TS4_PU (2) Internal pull-up resistance for TS4 After trim is loaded 17 18 19 kΩ
RNTC_PU_DRIFT(1) Internal pull-up resistance change over temperature Change over –40°C to +85°C vs value at 25°C for nominal 18kΩ –200 200 Ω
CI (1) Input capacitance TS1, TS2, TS3, TS4 2 pF
Ilkg(1) Input leakage current TS1, TS2, TS3, TS4 1 5 µA
(1) Specified by design. Not production tested
(2) The internal pull-up resistance includes only the resistance between the REG18 pin and the point where the voltage is sensed by the ADC