SLUUA65E april   2014  – june 2023 BQ28Z610

 

  1.   1
  2.   Read This First
    1.     About This Manual
    2.     Notational Conventions
    3.     Trademarks
    4.     Glossary
  3. 1 Introduction
  4. 2 Protections
    1. 2.1  Introduction
    2. 2.2  Cell Undervoltage Protection
    3. 2.3  Cell Overvoltage Protection
    4. 2.4  Overcurrent in Charge Protection
    5. 2.5  Overcurrent in Discharge Protection
    6. 2.6  Hardware-Based Protection
      1. 2.6.1 Overload in Discharge Protection
      2. 2.6.2 Short Circuit in Charge Protection
      3. 2.6.3 Short Circuit in Discharge Protection
    7. 2.7  Temperature Protections
    8. 2.8  Overtemperature in Charge Protection
    9. 2.9  Overtemperature in Discharge Protection
    10. 2.10 Undertemperature in Charge Protection
    11. 2.11 Undertemperature in Discharge Protection
    12. 2.12 Precharge Timeout Protection
    13. 2.13 Fast Charge Timeout Protection
  5. 3 Permanent Fail
    1. 3.1 Introduction
    2. 3.2 Safety Cell Overvoltage Permanent Fail
    3. 3.3 Voltage Imbalance at Rest Permanent Fail
    4. 3.4 Voltage Imbalance Active Permanent Fail
    5. 3.5 Charge FET Permanent Failure
      1. 3.5.1 Description
      2. 3.5.2 Feature Enable/Disable
    6. 3.6 Discharge FET Permanent Failure
      1. 3.6.1 Description
      2. 3.6.2 Feature Enable/Disable
    7. 3.7 Instruction Flash (IF) Checksum Permanent Fail
    8. 3.8 Data Flash (DF) Permanent Fail
  6. 4 Advanced Charge Algorithm
    1. 4.1  Introduction
    2. 4.2  Charge Temperature Ranges
    3. 4.3  Voltage Range
    4. 4.4  Charging Current
    5. 4.5  Charging Voltage
    6. 4.6  Valid Charge Termination
    7. 4.7  Charge and Discharge Alarms
    8. 4.8  Terminate Charge and Discharge Alarms
    9. 4.9  Precharge
    10. 4.10 Maintenance Charge
    11. 4.11 BROADCAST Mode
    12. 4.12 Charge Disable and Discharge Disable
    13. 4.13 Charge Inhibit
    14. 4.14 Charge Suspend
  7. 5 Power Modes
    1. 5.1 Introduction
    2. 5.2 NORMAL Mode
    3. 5.3 SLEEP Mode
      1. 5.3.1 Device Sleep
      2. 5.3.2 IN SYSTEM SLEEP Mode
      3. 5.3.3 AltManufacturerAccess() MAC Sleep
      4. 5.3.4 Wake Function
    4. 5.4 SHUTDOWN Mode
      1. 5.4.1 Voltage Based Shutdown
      2. 5.4.2 AltManufacturerAccess() MAC Shutdown
      3. 5.4.3 Time Based Shutdown
      4. 5.4.4 Emergency FET Shutdown
        1. 5.4.4.1 Exiting Emergency FET Shutdown
  8. 6 Gauging
    1. 6.1 Introduction
    2. 6.2 Impedance Track Configuration
    3. 6.3 Gas Gauge Modes
    4. 6.4 QMax and Ra
      1. 6.4.1 QMax Initial Values
      2. 6.4.2 QMax Update Conditions
      3. 6.4.3 Fast QMax Update Conditions
      4. 6.4.4 QMax and Fast QMax Update Boundary Check
      5. 6.4.5 Ra Table Initial Values
      6. 6.4.6 Ra Table Update Conditions
    5. 6.5 FullChargeCapacity (FCC), RemainingCapacity (RemCap), and RelativeStateOfCharge (RSOC)
    6. 6.6 Impedance Track (IT) Configuration Options
    7. 6.7 State-of-Health (SOH)
    8. 6.8 Battery Trip Point (BTP)
  9. 7 Cell Balancing
    1. 7.1 Introduction
    2. 7.2 Cell Balancing Setup
    3. 7.3 Cell Balancing Operation
  10. 8 Lifetime Data Collection
    1. 8.1 Description
  11. 9 Device Security
    1. 9.1 Description
    2. 9.2 SHA-1 Description
    3. 9.3 HMAC Description
    4. 9.4 Authentication
    5. 9.5 Security Modes
      1. 9.5.1 SEALING and UNSEALING Data Flash
      2. 9.5.2 SEALED to UNSEALED
      3. 9.5.3 UNSEALED to FULL ACCESS
  12. 10Manufacture Production
    1. 10.1 Manufacture Testing
    2. 10.2 Calibration
  13. 11Calibration
    1. 11.1 Cell Voltage Calibration
    2. 11.2 VC2 (BAT) Voltage Calibration
    3. 11.3 PACK Voltage Calibration
    4. 11.4 Current Calibration
      1. 11.4.1 CC Offset Calibration
      2. 11.4.2 Board Offset Calibration
      3. 11.4.3 CC Gain/Capacity Gain Calibration
    5. 11.5 Temperature Calibration
      1. 11.5.1 Internal Temperature Sensor Calibration
      2. 11.5.2 TS1 Calibration
  14. 12I2C Commands
    1. 12.1 Standard Data Commands
      1. 12.1.1  0x00/01 ManufacturerAccess() Control
      2. 12.1.2  0x02/03 AtRate()
      3. 12.1.3  0x04/05 AtRateTimeToEmpty()
      4. 12.1.4  0x06/07 Temperature()
      5. 12.1.5  0x08/09 Voltage()
      6. 12.1.6  0x0A/0B BatteryStatus()
      7. 12.1.7  0x0C/0D Current()
      8. 12.1.8  0x0E/0F MaxError()
      9. 12.1.9  0x10/11 RemainingCapacity()
      10. 12.1.10 0x12/13 FullChargeCapacity()
      11. 12.1.11 0x14/15 AverageCurrent()
      12. 12.1.12 0x16/17 AverageTimeToEmpty()
      13. 12.1.13 0x18/19 AverageTimeToFull()
      14. 12.1.14 0x1A/1B StandbyCurrent()
      15. 12.1.15 0x1C/1D StandbyTimeToEmpty()
      16. 12.1.16 0x1E/1F MaxLoadCurrent()
      17. 12.1.17 0x20/21 MaxLoadTimeToEmpty()
      18. 12.1.18 0x22/23 AveragePower()
      19. 12.1.19 0x24/25 BTPDischargeSet()
      20. 12.1.20 0x26/27 BTPChargeSet()
      21. 12.1.21 0x28/29 InternalTemperature()
      22. 12.1.22 0x2A/2B CycleCount()
      23. 12.1.23 0x2C/2D RelativeStateOfCharge()
      24. 12.1.24 0x2E/2F State-of-Health (SOH)
      25. 12.1.25 0x30/31 ChargingVoltage()
      26. 12.1.26 0x32/33 ChargingCurrent()
      27. 12.1.27 0x3C/3D DesignCapacity()
      28. 12.1.28 0x3E/3F AltManufacturerAccess()
      29. 12.1.29 0x40/0x5F MACData()
      30. 12.1.30 0x60 MACDataChecksum()
      31. 12.1.31 0x61 MACDataLength()
    2. 12.2 0x00, 0x01 AltManufacturerAccess() and 0x3E, 0x3F AltManufacturerAccess()
      1. 12.2.1  AltManufacturerAccess() 0x0001 Device Type
      2. 12.2.2  AltManufacturerAccess() 0x0002 Firmware Version
      3. 12.2.3  AltManufacturerAccess() 0x0003 Hardware Version
      4. 12.2.4  AltManufacturerAccess() 0x0004 Instruction Flash Signature
      5. 12.2.5  AltManufacturerAccess() 0x0005 Static DF Signature
      6. 12.2.6  AltManufacturerAccess() 0x0006 Chemical ID
      7. 12.2.7  AltManufacturerAccess() 0x0007 Pre_MACWrite
      8. 12.2.8  AltManufacturerAccess() 0x0008 Static Chem DF Signature
      9. 12.2.9  AltManufacturerAccess() 0x0009 All DF Signature
      10. 12.2.10 AltManufacturerAccess() 0x0010 SHUTDOWN Mode
      11. 12.2.11 AltManufacturerAccess() 0x0011 SLEEP Mode
      12. 12.2.12 AltManufacturerAccess() 0x0012 Device Reset
      13. 12.2.13 AltManufacturerAccess() 0x001F CHG FET
      14. 12.2.14 AltManufacturerAccess() 0x0020 DSG FET
      15. 12.2.15 AltManufacturerAccess() 0x0021 Gauging
      16. 12.2.16 AltManufacturerAccess() 0x0022 FET Control
      17. 12.2.17 AltManufacturerAccess() 0x0023 Lifetime Data Collection
      18. 12.2.18 AltManufacturerAccess() 0x0024 Permanent Failure
      19. 12.2.19 AltManufacturerAccess() 0x0028 Lifetime Data Reset
      20. 12.2.20 AltManufacturerAccess() 0x0029 Permanent Fail Data Reset
      21. 12.2.21 AltManufacturerAccess() 0x002D CALIBRATION Mode
      22. 12.2.22 AltManufacturerAccess() 0x0030 Seal Device
      23. 12.2.23 AltManufacturerAccess() 0x0035 Security Keys
      24. 12.2.24 AltManufacturerAccess() 0x0037 Authentication Key
      25. 12.2.25 AltManufacturerAccess() 0x0041 Device Reset
      26. 12.2.26 AltManufacturerAccess() 0x0050 SafetyAlert
      27. 12.2.27 AltManufacturerAccess() 0x0051 SafetyStatus
      28. 12.2.28 AltManufacturerAccess() 0x0052 PFAlert
      29. 12.2.29 AltManufacturerAccess() 0x0053 PFStatus
      30. 12.2.30 AltManufacturerAccess() 0x0054 OperationStatus
      31. 12.2.31 AltManufacturerAccess() 0x0055 ChargingStatus
      32. 12.2.32 AltManufacturerAccess() 0x0056 GaugingStatus
      33. 12.2.33 AltManufacturerAccess() 0x0057 ManufacturingStatus
      34. 12.2.34 AltManufacturerAccess() 0x0058 AFE Register
      35. 12.2.35 AltManufacturerAccess() 0x0060 Lifetime Data Block 1
      36. 12.2.36 AltManufacturerAccess() 0x0070 ManufacturerInfo
      37. 12.2.37 AltManufacturerAccess() 0x0071 DAStatus1
      38. 12.2.38 AltManufacturerAccess() 0x0072 DAStatus2
      39. 12.2.39 AltManufacturerAccess() 0x0073 ITStatus1
      40. 12.2.40 AltManufacturerAccess() 0x0074 ITStatus2
      41. 12.2.41 AltManufacturerAccess() 0x0075 ITStatus3
      42. 12.2.42 AltManufacturerAccess() 0x0076 CB Status
      43. 12.2.43 AltManufacturerAccess() 0x0077 State-of-Health
      44. 12.2.44 AltManufacturerAccess() 0x0F00 ROM Mode
      45. 12.2.45 Data Flash Access() 0x4000–0x5FFF
      46. 12.2.46 AltManufacturerAccess() 0xF080 Exit Calibration Output Mode
      47. 12.2.47 AltManufacturerAccess() 0xF081 Output CC and ADC for Calibration
      48. 12.2.48 AltManufacturerAccess() 0xF082 Output Shorted CC and ADC for Calibration
  15. 13Data Flash Values
    1. 13.1  Data Formats
      1. 13.1.1 Unsigned Integer
      2. 13.1.2 Integer
      3. 13.1.3 Floating Point
      4. 13.1.4 Hex
      5. 13.1.5 String
    2. 13.2  Calibration
      1. 13.2.1 Voltage
      2. 13.2.2 Current
      3. 13.2.3 Current Offset
      4. 13.2.4 Current Deadband
      5. 13.2.5 Temperature
      6. 13.2.6 Internal Temp Model
      7. 13.2.7 Cell Temp Model
    3. 13.3  Settings
      1. 13.3.1 Configuration
      2. 13.3.2 Charger
      3. 13.3.3 Protection
      4. 13.3.4 Permanent Failure
      5. 13.3.5 AFE
      6. 13.3.6 Manufacturing
    4. 13.4  Advanced Charging Algorithms
      1. 13.4.1  Temperature Ranges
      2. 13.4.2  Low Temp Charging
      3. 13.4.3  Standard Temp Charging
      4. 13.4.4  High Temp Charging
      5. 13.4.5  Rec Temp Charging
      6. 13.4.6  Pre-Charging
      7. 13.4.7  Maintenance Charging
      8. 13.4.8  Voltage Range
      9. 13.4.9  Termination Config
      10. 13.4.10 Cell Balancing Config
    5. 13.5  Power
      1. 13.5.1 Power
      2. 13.5.2 Shutdown
      3. 13.5.3 Sleep
      4. 13.5.4 Ship
    6. 13.6  Gas Gauging
      1. 13.6.1  Standby
      2. 13.6.2  Max Load
      3. 13.6.3  Current Thresholds
      4. 13.6.4  Design
      5. 13.6.5  Cycle
      6. 13.6.6  FD
      7. 13.6.7  FC
      8. 13.6.8  TDA
      9. 13.6.9  TCA
      10. 13.6.10 State
      11. 13.6.11 IT Config
      12. 13.6.12 Condition Flag
      13. 13.6.13 SOH
      14. 13.6.14 Max Error
    7. 13.7  System Data
      1. 13.7.1 Manufacturer Data
      2. 13.7.2 Integrity
    8. 13.8  Configuration
      1. 13.8.1 Data
    9. 13.9  Lifetimes
      1. 13.9.1 Voltage
      2. 13.9.2 Current
      3. 13.9.3 Temperature
    10. 13.10 Protections
      1. 13.10.1  CUV—Cell Undervoltage
      2. 13.10.2  COV—Cell Overvoltage
      3. 13.10.3  OCC—Overcurrent In Charge
      4. 13.10.4  OCD—Overcurrent In Discharge
      5. 13.10.5  AOLD—AFE Over Load In Discharge
      6. 13.10.6  ASCC—AFE Short Circuit in Charge
      7. 13.10.7  ASCD—AFE Short Circuit in Discharge
      8. 13.10.8  OTC—Overtemperature in Charge
      9. 13.10.9  OTD—Overtemperature in Discharge
      10. 13.10.10 UTC—Under Temperature in Charge
      11. 13.10.11 UTD—Under Temperature in Discharge
      12. 13.10.12 PTO—PRECHARGE Mode Time Out
      13. 13.10.13 CTO—FAST CHARGE Mode Time Out
    11. 13.11 Permanent Fail
      1. 13.11.1 SOV—Safety Cell Overvoltage
      2. 13.11.2 VIMR—Voltage Imbalance at Rest
      3. 13.11.3 VIMA—Voltage Imbalance Active
    12. 13.12 PF Status
      1. 13.12.1 Device Status
      2. 13.12.2 275
      3. 13.12.3 Device Voltage Data
      4. 13.12.4 Device Current Data
      5. 13.12.5 Device Temperature Data
      6. 13.12.6 Device Gauging Data
      7. 13.12.7 AFE Registers
    13. 13.13 RA Table
      1. 13.13.1 R_a0
      2. 13.13.2 R_a1
      3. 13.13.3 R_a0x
      4. 13.13.4 R_a1x
  16. 14Data Flash Summary
    1. 14.1 Data Flash Table
  17.   A AFE Threshold and Delay Settings
    1.     A.1 Overload in Discharge Protection (AOLD)
    2.     A.2 Short Circuit in Charge (ASCC)
    3.     A.3 Short Circuit in Discharge (ASCD1 and ASCD2)
  18.   B Revision History

13.6.11 IT Config

Class Subclass Name Type Min Max Default Unit Description
Gas Gauging IT Cfg Pack Resistance I2 0 32767 30 mΩ
Gas Gauging IT Cfg System Resistance I2 0 32767 0 mΩ
Gas Gauging IT Cfg Ra Filter U2 0 999 500 0.1% Filter value used in Ra updates, specifies what percentage or Ra update is from a new value (100%—setting) vs. an old value (setting). The recommended setting is 80% if the RSOC_CONV feature is enabled; otherwise, the setting should be 50% as the default.
Gas Gauging IT Cfg Ra Max Delta U1 0 255 15 % of Design Resistance Maximum value of allowed Ra change
Gas Gauging IT Cfg Reference Grid UI 0 15 4 Reference Grid point used by Design Resistance. The default setting should be used if RSOC_CONV feature is enabled; otherwise, grid point 11 should be used to ensure resistance updates fast enough at the grid where discharge termination occurs.
Gas Gauging IT Cfg Resistance Parameter Filter U2 1 65534 65124 — This is one of the filters used for resistance update. Reducing this filter setting can improve low temperature performance at high rates. The default setting is 41-s time constant. It is recommended to keep this filter within the range of 4 s (that is, DF setting = 61680) up to the default 41 s (that is, DF setting = 65142).
Examining the Term Voltage Delta setting and Fast Scale Start SOC should be done prior to twisting this parameter when trying to improve the RSOC performance.
The following is the formula to convert the DF setting into actual filter time constant: Filter time constant = [0.25/(1 – (DF_Value /65536))] – 0.25.
Gas Gauging IT Cfg Near EDV Ra Param Filter U2 1 65535 59220 — This is the Ra filter used in the fast scaling region if [FF_NEAR_EDV] = 1. The default value should be used.
Gas Gauging IT Cfg QMax Delta U1 3 100 5 % Maximum allowed QMax change from its previous value. The QMax change is capped by this setting if the delta from the previous QMax is larger than QMax Delta. QMax Delta is a percentage of Design Capacity.
Gas Gauging IT Cfg QMax Upper Bound U1 100 255 130 % Maximum QMax value over the lifetime of the pack. If the updated QMax value is larger than this setting, the updated QMax is capped to QMax Upper Bound. QMax Upper Bound is a percentage of Design Capacity.
Gas Gauging IT Cfg Term Voltage I2 0 32767 9000 mV Min stack voltage to be used for capacity calculation
Gas Gauging IT Cfg Max Simulation Iterations U1 20 50 30 The maximum number of iterations allowed for simulation
Gas Gauging IT Cfg Term Voltage Delta I2 0 32767 300 mV Controls when the RSOC_CONV feature becomes active. The recommended setting is 3.3 –Term Voltage/Number Cells.
The default setting is 300 mV, which is assuming a typical 3-V termination voltage per cell. If a different termination voltage is used, this parameter should be adjusted accordingly.
Gas Gauging IT Cfg Term Min Cell Voltage I2 0 32767 2800 mV Minimum cell termination voltage when used, if [CELL_TERM]= 1. This is intended to enable the IT algorithm to reach 0% before CUV is triggered; therefore, this value should be set at or above CUV:Threshold.
Gas Gauging IT Cfg Fast Scale Start SOC U1 0 100 10 % Control start of convergence when [RSOC_CONV]= 1 based on RSOC %. Raising this setting can improve the RSOC drop at the end of discharge. However the RSOC % chosen for this setting must keep after the sharp drop of the discharge curve (the knee of the discharge curve).
Gas Gauging IT Cfg Load Select U1 0 255 7 Defines load compensation mode used by the gauging algorithm
Gas Gauging IT Cfg Load Mode U1 0 255 0 Defines the unit used by the gauging algorithm:
0 = Constant Current
1 = Constant Power
Gas Gauging IT Cfg Design Resistance I2 0 32767 96 mΩ Averaged cell resistance at Reference Grid point. Automatically updated when Update Status is set to 0x6 by the gauge. To automatically update again, set Update Status to 0x4 or manually set when Update Status is set to 0x6.
Gas Gauging IT Cfg User-Rate-mA I2 –9000 0 0 mA Discharge rate used for capacity calculation selected by Load Select
Gas Gauging IT Cfg User-Rate-cW I2 –32768 0 0 cW Discharge rate used for capacity calculation selected by Load Select
Gas Gauging IT Cfg Reserve Cap-mAh I2 0 9000 0 mAh Capacity is reserved available when the gauging algorithm reports 0% RelativeStateOfCharge().
Gas Gauging IT Cfg Reserve Cap-cWh I2 0 32000 0 cWh Capacity reserved is available when the gauging algorithm reports 0% RelativeStateOfCharge().