SLVA275C january   2010  – may 2023 UCD9081

 

  1.   Abstract
  2.   Trademarks
  3. 1Introduction
  4. 2Hardware
    1. 2.1 Package: RHB (S-PQFP-N32), 32-Pin Plastic Quad Flatpack
    2. 2.2 Hardware and Pinout
    3. 2.3 Detailed Pin Descriptions
      1. 2.3.1 RST
      2. 2.3.2 SDA
      3. 2.3.3 SCL
      4. 2.3.4 ADDRx
      5. 2.3.5 ROSC
  5. 3Software
    1. 3.1 Data File Format
    2. 3.2 I2C Transactions
    3. 3.3 Device Version
    4. 3.4 Checksum
    5. 3.5 Sample Configuration Data File
      1. 3.5.1 Factory Default
      2. 3.5.2 EVM Default Configuration
    6. 3.6 I2C Write and Read Transaction Formats
      1. 3.6.1 I2C Write Transaction
      2. 3.6.2 I2C Read Transaction
    7. 3.7 Pseudo I2C Write and Read Transactions
      1. 3.7.1 UCD9081 I2C Transactions for Writing User Data and PARAMS
      2. 3.7.2 UCD9081 I2C Transactions for Reading User Data and PARAMS
  6. 4User Configuration
    1. 4.1 Configuration Parameter Memory Map
    2. 4.2 Configuration Parameter Detail
      1. 4.2.1  GpDir
      2. 4.2.2  NegateEnablePolarity
      3. 4.2.3  SeqEventPending
      4. 4.2.4  SequenceEventParameters
      5. 4.2.5  SequenceEventLink
      6. 4.2.6  SequenceEventData
      7. 4.2.7  DependencyMasks
      8. 4.2.8  UnderVoltageThresholds
      9. 4.2.9  OverVoltageThresholds
      10. 4.2.10 RampTime
      11. 4.2.11 OutOfRegulationWidth
      12. 4.2.12 UnsequenceTime
      13. 4.2.13 EnablePolarity
      14. 4.2.14 SaveRailLog
      15. 4.2.15 ReferenceSelect
      16. 4.2.16 LastUnusedSeq
      17. 4.2.17 IgnoreGlitchAlarms
      18. 4.2.18 IgnoreFlashErrorLog
      19. 4.2.19 Checksum
  7. 5Additional Considerations
    1. 5.1 Embedded Application
    2. 5.2 Timing
      1. 5.2.1 UCD9081 Startup
      2. 5.2.2 Clock Stretching After Flash Erase
      3. 5.2.3 Bit Timeout
      4. 5.2.4 Byte or Transaction Timeout
  8. 6References
  9. 7Revision History

4.2.2 NegateEnablePolarity

The NegateEnablePolarity field in the configuration parameters allows for the selection of enable signal for RAILn and GPOn to be active high or active low. These values should align with bit 16 of the EnablePolarity registers (R[0xE168] to R[0xE17E]) (see Section 4.2.13). If the RAIL or GPO is set as enable active-low (value = 0b), the corresponding NegateEnablePolarity bit value should also be set 1b. The register contents are as follows:

Address Size Default Value Description
0xE04A 2 0x0000 NegateEnable signal parameters for Railn and GPOn

The format of the register is as follows:

GUID-0864EE07-A9D6-4E8E-82B7-3706F9AA8F04-low.svg
RAILn or GPOn Meaning
0 Enable signal set as active-high (1b) for RAILn or GPOn in R[0xE168]:R[0xE17E], bit[16]
1 Enable signal set as active-low (0b) for RAILn or GPOn in R[0xE168]:R[0xE17E], bit[16]