SLVSDT3D January   2018  – December 2019 TPS25221

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
    1.     Device Images
      1.      Simplified Schematic
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Over-current Conditions
      2. 9.3.2 Fault Response
      3. 9.3.3 Undervoltage Lockout (UVLO)
      4. 9.3.4 Enable, (EN)
      5. 9.3.5 Thermal Sense
    4. 9.4 Device Functional Modes
    5. 9.5 Programming
      1. 9.5.1 Programming the Current-Limit Threshold
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Constant-Current
    2. 10.2 Typical Applications
      1. 10.2.1 Two-Level Current-Limit Circuit
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedures
          1. 10.2.1.2.1 Designing Above a Minimum Current Limit
          2. 10.2.1.2.2 Designing Below a Maximum Current Limit
          3. 10.2.1.2.3 Accounting for Resistor Tolerance
          4. 10.2.1.2.4 Input and Output Capacitance
        3. 10.2.1.3 Application Curve
      2. 10.2.2 Auto-Retry Functionality
        1. 10.2.2.1 Design Requirements (added)
        2. 10.2.2.2 Detailed Design Procedure
      3. 10.2.3 Typical Application as USB Power Switch
        1. 10.2.3.1 Design Requirements
          1. 10.2.3.1.1 USB Power-Distribution Requirements
        2. 10.2.3.2 Detailed Design Procedure
          1. 10.2.3.2.1 Universal Serial Bus (USB) Power-Distribution Requirements
  11. 11Power Supply Recommendations
    1. 11.1 Self-Powered and Bus-Powered Hubs
    2. 11.2 Low-Power Bus-Powered and High-Power Bus-Powered Functions
    3. 11.3 Power Dissipation and Junction Temperature
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Community Resources
    5. 13.5 Trademarks
    6. 13.6 Electrostatic Discharge Caution
    7. 13.7 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

7.6 Typical Characteristics

See Figure 21 for reference schematic
TPS25221 slvsdt3_turn_on_delay.png
VIN = 5 V, RILIM = 20 kΩ, ROUT = 5 Ω
Figure 5. Turnon Delay and Rise Time
TPS25221 slvsdt3_enable_to_short.png
VIN = 5 V, RILIM = 20 kΩ, ROUT = 0 Ω
Figure 7. Device Enabled into Short-Circuit
TPS25221 tek00028.png
VIN = 5 V, RILIM = 20 kΩ
Figure 9. Short-Circuit to Full-Load Recovery Response
TPS25221 short_to_no_load2.png
VIN = 5 V, RILIM = 20 kΩ
Figure 11. Short-Circuit to No-Load Recovery Response
TPS25221 1R_to_No_load.png
VIN = 5 V, RILIM = 20 kΩ
Figure 13. 1-Ω to No Load Transient Response
TPS25221 D007_new.gif
RILIM = 20 kΩ
Figure 15. IIN – Supply Current, Output Disabled – µA
TPS25221 D006_SLVSDT3.gif
VIN = 5 V, RILIM = 20 kΩ, TA = 25°C
Figure 17. Current Limit Response – µs
TPS25221 Currentlimit20K_new.gif
VIN = 5.5 V, RILIM = 20 kΩ
Figure 19. Switch Current Vs. Drain-Source Voltage Across Switch
TPS25221 slvsdt3_turn_off_delay.png
VIN = 5 V, RILIM = 20 kΩ, ROUT = 5 Ω
Figure 6. Turnoff Delay and Fall Time
TPS25221 slvsdt3_full_load_to_short.png
VIN = 5 V, RILIM = 20 kΩ
Figure 8. Full-Load to Short-Circuit Transient Response
TPS25221 tek00034.png
VIN = 5 V, RILIM = 20 kΩ
Figure 10. No-Load to Short-Circuit Transient Response
TPS25221 No_load_to_1R.png
VIN = 5 V, RILIM = 20 kΩ
Figure 12. No Load to 1-Ω Transient Response
TPS25221 UVLO_6.gif
RILIM = 20 kΩ
Figure 14. UVLO – Undervoltage Lockout – V
TPS25221 D008_new.gif
RILIM = 20 kΩ
Figure 16. IIN – Supply Current, Output Enabled – µA
TPS25221 D004_new.gif
Figure 18. On-Resistance Vs. Junction Temperature
TPS25221 D006_new.gif
VIN = 5.5 V, RILIM = 210 kΩ
Figure 20. Switch Current Vs. Drain-Source Voltage Across Switch