SLVSGT9B February   2023  – June 2024 TPS25948

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Undervoltage Lockout (UVLO and UVP)
      2. 7.3.2 Overvoltage Lockout (OVLO)
      3. 7.3.3 Inrush Current, Overcurrent, and Short Circuit Protection
        1. 7.3.3.1 Slew Rate (dVdt) and Inrush Current Control
        2. 7.3.3.2 Active Current Limiting
        3. 7.3.3.3 Short-Circuit Protection
      4. 7.3.4 Analog Load Current Monitor
      5. 7.3.5 Reverse Current Protection
      6. 7.3.6 Overtemperature Protection (OTP)
      7. 7.3.7 Fault Response and Indication (FLT)
      8. 7.3.8 Supply Good Indication (SPLYGD/SPLYGD)
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Single Device, Self-Controlled
    3. 8.3 Typical Application
      1. 8.3.1 Design Requirements
      2. 8.3.2 Detailed Design Procedure
        1. 8.3.2.1 Setting Overvoltage Threshold
        2. 8.3.2.2 Setting Output Voltage Rise Time (tR)
        3. 8.3.2.3 Setting Overcurrent Threshold (ILIM)
        4. 8.3.2.4 Setting Overcurrent Blanking Interval (tITIMER)
      3. 8.3.3 Application Curves
    4. 8.4 Active ORing
    5. 8.5 Priority Power MUXing
    6. 8.6 Parallel Operation
    7. 8.7 USB PD Port Protection
    8. 8.8 Power Supply Recommendations
      1. 8.8.1 Transient Protection
      2. 8.8.2 Output Short-Circuit Measurements
    9. 8.9 Layout
      1. 8.9.1 Layout Guidelines
      2. 8.9.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
Parameter Pin MIN MAX UNIT
VIN,MAX Maximum input voltage range, –40℃ ≤ TJ ≤ 125℃ IN –0.3 28 V
VOUT,MAX Maximum output voltage range, –40℃ ≤ TJ ≤ 125℃ OUT –0.3 min (28, VIN + 21)
VOUT,MAX Maximum output voltage range, -10℃ ≤ TJ ≤ 125 ℃ OUT –0.3 min (28, VIN + 22)
VOUT,MAX,PLS Minimum output voltage pulse (< 1 µs) OUT –0.8
VEN/UVLO,MAX Maximum enable pin voltage range EN/UVLO –0.3 6.5 V
VOVLO,MAX Maximum OVLO pin voltage range OVLO –0.3 6.5 V
VdVdt,MAX Maximum dVdT pin voltage range dVdt Internally limited V
VITIMER,MAX Maximum ITIMER pin voltage range ITIMER Internally limited V
VRCBCTRL,MAX Maximum RCBCTRL pin voltage range RCBCTRL –0.3 6.5 V
VSPLYGD,MAX Maximum SPLYGD/SPLYGD pin voltage range SPLYGD/SPLYGD –0.3 6.5 V
VFLTB,MAX Maximum FLT pin voltage range FLT –0.3 6.5 V
VILM,MAX Maximum ILM pin voltage range ILM Internally limited V
IMAX Maximum continuous switch current IN to OUT or OUT to IN Internally limited A
TJ,MAX Maximum operating junction temperature Internally limited °C
TLEAD,MAX Maximum lead temperature 300 °C
TSTG,MAX Maximum storage temperature –65 150 °C
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions.
If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully
functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.