SLVUC07A December   2020  – May 2021 TPS543320

 

  1.   Trademarks
  2. 1Introduction
    1. 1.1 Background
    2. 1.2 Before You Begin
    3. 1.3 Performance Characteristics Summary
  3. 2Configurations and Modifications
    1. 2.1 Output Voltage
    2. 2.2 Switching Frequency (FSEL Pin)
    3. 2.3 Current Limit, Soft-Start Time, and Internal Compensation (MODE Pin)
    4. 2.4 Adjustable UVLO
  4. 3Test Setup and Results
    1. 3.1  Input/Output Connections
    2. 3.2  Efficiency
    3. 3.3  Output Voltage Regulation
    4. 3.4  Load Transient and Loop Response
    5. 3.5  Output Voltage Ripple
    6. 3.6  Input Voltage Ripple
    7. 3.7  Synchronizing to a Clock
    8. 3.8  Start-up and Shutdown with EN
    9. 3.9  Start-up and Shutdown with VIN
    10. 3.10 Hiccup Current Limit
    11. 3.11 Overvoltage Protection
    12. 3.12 Thermal Performance
  5. 4Board Layout
    1. 4.1 Layout
  6. 5Schematic and Bill of Materials
    1. 5.1 Schematic
    2. 5.2 Bill of Materials
  7. 6Revision History

2.1 Output Voltage

In the U1 design, the output voltage is set by the resistor divider network of R7 (RFBT) and R8 (RFBB). R8 is fixed at 1.00 kΩ to set the FB divider current at approximately 500 µA. To change the output voltage of the EVM, the value of resistor R7 must change. Changing the value of R7 can change the output voltage above the 0.5-V reference voltage (VREF). The value of R7 for a specific output voltage can be calculated using Equation 1. After changing R7, the feedfoward capacitor (C8) can also need to be changed.

Equation 1. GUID-E0502BD8-2825-4C14-A517-A473BC736BFF-low.gif

In the U2 design, there are a few ways to set the output voltage. First, jumper J14 can be used to select between the options shown in Table 2-1. If the desired output voltage is not available, a resistor must be changed. For output voltages less than 0.8 V, TI recommends leaving J14 open and increasing R21. R21 becomes RFBB and the required value for can be calculated with Equation 2, where RFBT is R15. For output voltages greater than 0.8 V, the jumper output voltage options can be changed by changing one of the resistors R23-R26. The RFBJ resistor value to get a desired equivalent RFBB resistance can be calculated with Equation 3. To use J14 for output voltages 3.3 V or larger, R20 should be reduced to 499 Ω.

Equation 2. GUID-E1775238-34E1-4924-8CDC-3E7EB96C9684-low.gif
Equation 3. GUID-20200824-CA0I-Q1NW-JTWH-RDZZXQZF7CK8-low.gif
Table 2-1 VOUT Selection
JUMPER SETTING EQUIVALENT BOTTOM FB RESISTOR (RFBB) NOMINAL OUTPUT VOLTAGE
Open R21 = 20.0 kΩ 1.2 V
1 to 2 pin shorted (R23+R20)||R21 = 6.08 kΩ 1.8 V
3 to 4 pin shorted (R24+R20)||R21 = 4.67 kΩ 2.5 V
5 to 6 pin shorted(1) (R25+R20)||R21 = 3.67 kΩ 3.3 V
7 to 8 pin shorted (R26+R20)||R21 = 2.54 kΩ 5.0 V
(1) Default Setting