SNAU305 February   2025 LMH1229 , LMH1239

1.   1
2.   LMH1229 and LMH1239 Programming Guide
3.   Trademarks
4. 1Access Methods
   1. 1.1 Register Programming Through SMBus
   2. 1.2 Register Programming Through SPI
   3. 1.3 Register Pages
5. 2Register Command Syntax
6. 3Device Configurations
   1. 3.1  Common Device Configuration
   2. 3.2  Common Register Commands
      1. 3.2.1 Channel Control
      2. 3.2.2 LMH12x9 Resets
         1. 3.2.2.1 LMH12x9 ENABLE Pin Override
         2. 3.2.2.2 LMH12x9 Share, CDR, and EQ/Drivers Page Resets
   3. 3.3  IN_MUX_SEL Override
   4. 3.4  Signal Detect Status for SDI_IN± and SDI_IN1±
      1. 3.4.1 Force Signal Detect Power Down
   5. 3.5  Lock Data Rate Indication
   6. 3.6  CDR Loop Bandwidth Override
   7. 3.7  Selective SMPTE Data Rate Lock
      1. 3.7.1 Digital Mute Reference Threshold
      2. 3.7.2 CTLE Index Check and Manual CTLE Override
   8. 3.8  Eye Opening Monitoring Operation
      1. 3.8.1 Fast EOM
         1. 3.8.1.1 Fast EOM Operation
      2. 3.8.2 Read Horizontal and Vertical Eye Opening
   9. 3.9  SDI_OUT±, OUT0± and OUT1± Default Mode of Operation
      1. 3.9.1 SDI_OUT±, OUT0± and OUT1± Independent Control
   10. 3.10 Invert OUT0±, OUT1±, and SDI_OUT± Data Polarity
   11. 3.11 OUT0±, OUT1±, and SDI_OUT± Driver Settings
       1. 3.11.1 OUT0± and OUT1± VOD Settings
       2. 3.11.2 OUT0± and OUT1± De-Emphasis Settings
       3. 3.11.3 SDI_OUT± VOD Settings
       4. 3.11.4 SDI_OUT± Pre-Emphasis
       5. 3.11.5 Output Driver Power Down
       6. 3.11.6 Cable Fault Detection (CFD)
   12. 3.12 LOCK_N Pin Output Settings
       1. 3.12.1 Interrupt Outputs Programmed by Interrupt Registers
   13. 3.13 PRBS Generator and Checker
   14. 3.14 CDR Lock Timing Control
       1. 3.14.1 Watchdog Timer
7. 4Register Maps
   1. 4.1 Share Registers
   2. 4.2 CDR Registers
   3. 4.3 EQ_Drivers Registers

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2025, Texas Instruments Incorporated