SPRACF4C June   2018  – January 2023 AWR1243 , AWR1443 , AWR1642 , AWR1843 , AWR1843AOP , AWR2243 , AWR2944 , AWR6843 , AWR6843AOP , IWR1843 , IWR2944 , IWR6443 , IWR6843 , IWR6843AOP

1.   Trademarks
2. 1Introduction
   1. 1.1 Purpose of Calibrations
   2. 1.2 Purpose of Monitoring Mechanisms
3. 2Hardware Infrastructure to Support Calibration and Monitoring
4. 3List of Calibrations
   1. 3.1  APLL Calibration
   2. 3.2  Synthesizer VCO Calibration
   3. 3.3  LO Distribution Calibration
   4. 3.4  ADC DC Offset Calibration
   5. 3.5  HPF Cutoff Calibration
   6. 3.6  LPF Cutoff Calibration
   7. 3.7  Peak Detector Calibration
   8. 3.8  TX Power Calibration
   9. 3.9  RX Gain Calibration
   10. 3.10 IQ Mismatch Calibration
   11. 3.11 TX Phase Shifter Calibration
5. 4Impact of Calibration on Gain and Phase
6. 5Impact of Interference on the Calibrations and Emissions Caused Due to Calibrations
7. 6Scheduling of Runtime Calibration and Monitoring
   1. 6.1 Selection of CALIB_MON_TIME_UNIT
   2. 6.2 Selection of CALIBRATION_PERIODICITY
   3. 6.3 Application-Controlled One Time Calibration
8. 7Software Controllability of Calibration
   1. 7.1  Calibration and Monitoring Frequency Limits
   2. 7.2  Calibration and Monitoring TX Frequency and Power Limit
   3. 7.3  Calibration Status Reports
      1. 7.3.1 RF Initialization Calibration Completion
      2. 7.3.2 Runtime Calibration Status Report
      3. 7.3.3 Calibration/Monitoring Timing Failure Status Report
   4. 7.4  Programming CAL_MON_TIME_UNIT
   5. 7.5  Calibration Periodicity
   6. 7.6  RF Initialization Calibration
   7. 7.7  Runtime Calibration
   8. 7.8  Overriding the TX Power Calibration LUT
   9. 7.9  Overriding the RX Gain Calibration LUT
   10. 7.10 Retrieving and Restoring Calibration Data
9. 8References
10.   A Calibration and Monitoring Durations
    1.     A.1 Duration of Boot Time Calibrations
11.   Revision History

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2023, Texas Instruments Incorporated