SPRACU5C June   2021  – September 2023 AM2431 , AM2432 , AM2434 , AM6411 , AM6412 , AM6421 , AM6422 , AM6441 , AM6442

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1 Introduction
    1. 1.1 AM64x Processor Family
    2. 1.2 AM243x Processor Family
  5. 2 Related Collaterals
    1. 2.1 Hardware Design Guide
  6. 3 Processor Selection
    1. 3.1 Data Sheet
    2. 3.2 Peripheral Instance Naming Convention
    3. 3.3 Processor Ordering and Quality
  7. 4 Power Architecture
    1. 4.1 Generating Supply Rails
      1. 4.1.1 PMIC (Power Management IC)
        1. 4.1.1.1 Additional Reference
      2. 4.1.2 Discrete Power
        1. 4.1.2.1 DC/DC Converter
        2. 4.1.2.2 LDO
    2. 4.2 Power
      1. 4.2.1 Load Switch
      2. 4.2.2 eFuse
  8. 5 General Recommendations
    1. 5.1 Processor Performance Evaluation Module (EVM)
    2. 5.2 EVM Versus Data Sheet
      1. 5.2.1 Note About Component Selection
        1. 5.2.1.1 Series Resistor
        2. 5.2.1.2 Parallel Termination
        3. 5.2.1.3 External ESD Protection
      2. 5.2.2 Additional Information
    3. 5.3 Before You Begin The Design
      1. 5.3.1  Documentation
      2. 5.3.2  Processor Pinout Verification
      3. 5.3.3  IOSET
      4. 5.3.4  Note on PADCONFIG Register
      5. 5.3.5  Signal Isolation for Fail-Safe Operation
      6. 5.3.6  Reference to EVM or SK
      7. 5.3.7  Board Design - Layers Optimization
      8. 5.3.8  Termination of Unused Processor Pins
      9. 5.3.9  Naming of Peripheral Instances
      10. 5.3.10 High-Speed Interface Design Guidelines
      11. 5.3.11 Voltage and Thermal Manager (VTM) Module
      12. 5.3.12 Allowed GPIO Current Source or Sink
      13. 5.3.13 Connection of Capacitor to LVCMOS Type IO (Input or Output)
      14. 5.3.14 Processor Related Queries and Clarifications
  9. 6 Processor Specific Recommendations
    1. 6.1 Common (Processor Start-Up) Connection
      1. 6.1.1 Power Supply
        1. 6.1.1.1 Supplies for Core and Peripherals
          1. 6.1.1.1.1 Power Supply Ramp (Slew Rate) Requirement and Dynamic Voltage Scaling
        2. 6.1.1.2 Supply for IO Groups
        3. 6.1.1.3 Supply for VPP (eFuse ROM Programming)
        4. 6.1.1.4 Additional Information
      2. 6.1.2 Capacitors for Supply Rails
        1. 6.1.2.1 Additional Information
      3. 6.1.3 Processor Clock
        1. 6.1.3.1 Clock Inputs
          1. 6.1.3.1.1 High Frequency Oscillator (MCU_OSC0_XI/ MCU_OSC0_XO)
          2. 6.1.3.1.2 External Clock Input to Main Domain (EXT_REFCLK1)
          3. 6.1.3.1.3 Additional Information
        2. 6.1.3.2 Clock Output
      4. 6.1.4 Processor Reset
        1. 6.1.4.1 Reset Inputs
        2. 6.1.4.2 Reset Status Outputs
        3. 6.1.4.3 Additional Information
      5. 6.1.5 Configuration of Boot Modes (for Processor)
        1. 6.1.5.1 Processor Boot Mode Inputs Isolation Buffers Use Case and Optimization
        2. 6.1.5.2 Bootmode Selection
          1. 6.1.5.2.1 Notes for USB Boot Mode
        3. 6.1.5.3 Additional Information
    2. 6.2 Board Debug Using JTAG and EMU
      1. 6.2.1 Additional Information
  10. 7 Processor Peripherals
    1. 7.1 Power Supply Connections for IO Groups
    2. 7.2 Memory Interface (DDR4, LPDDR4, MMCSD (eMMC/SD/SDIO), OSPI/QSPI and GPMC)
      1. 7.2.1 DDR Subsystem (DDRSS)
        1. 7.2.1.1 Double Data Rate 4 (DDR4)
          1. 7.2.1.1.1 Interface Configuration
          2. 7.2.1.1.2 Routing Topology and Terminations
          3. 7.2.1.1.3 Resistors for Control and Calibration
          4. 7.2.1.1.4 Capacitors for the Power Supply Rails
          5. 7.2.1.1.5 Data Bit or Byte Swapping
        2. 7.2.1.2 Low-Power Double Data Rate 4 (LPDDR4)
          1. 7.2.1.2.1 Interface Configuration
          2. 7.2.1.2.2 Routing Topology and Terminations
          3. 7.2.1.2.3 Resistors for Control and Calibration
          4. 7.2.1.2.4 Capacitors for the Power Supply Rails
          5. 7.2.1.2.5 Data Bit or Byte Swapping
      2. 7.2.2 Multi-Media Card/Secure Digital (MMCSD)
        1. 7.2.2.1 MMC0 - eMMC (Embedded Multi-Media Card) Interface
          1. 7.2.2.1.1 MMC0 Used
            1. 7.2.2.1.1.1 IO Power Supply
            2. 7.2.2.1.1.2 eMMC Reset
            3. 7.2.2.1.1.3 Signals Termination
            4. 7.2.2.1.1.4 Capacitors for the Power Supply Rails
          2. 7.2.2.1.2 MMC0 Not Used
          3. 7.2.2.1.3 Additional Information
        2. 7.2.2.2 MMC1 – Secure Digital (SD) Card Interface
          1. 7.2.2.2.1 IO Power Supply
          2. 7.2.2.2.2 SD Card Reset and Boot
          3. 7.2.2.2.3 Signals Termination
          4. 7.2.2.2.4 ESD Protection
          5. 7.2.2.2.5 Capacitors for the Power Supply Rails
        3. 7.2.2.3 Additional Information
      3. 7.2.3 Octal Serial Peripheral Interface (OSPI) or Quad Serial Peripheral Interface (QSPI)
        1. 7.2.3.1 IO Power Supply
        2. 7.2.3.2 OSPI / QSPI Reset
        3. 7.2.3.3 Signals Termination
        4. 7.2.3.4 Loopback Clock
        5. 7.2.3.5 Interface to Multiple Devices
        6. 7.2.3.6 Capacitors for the Power Supply Rails
      4. 7.2.4 General-Purpose Memory Controller (GPMC)
        1. 7.2.4.1 IO Power Supply
        2. 7.2.4.2 GPMC Interface
        3. 7.2.4.3 Memory Reset
        4. 7.2.4.4 Signals Termination
        5. 7.2.4.5 Capacitors for the Power Supply Rails
    3. 7.3 External Communication Interface (Ethernet (CPSW3G and PRU_ICSSG), USB2.0, USB3.0 (SERDES), PCIe (SERDES), UART and CAN)
      1. 7.3.1 Ethernet Interface (CPSW3G and PRU_ICSSG)
        1. 7.3.1.1  IO Power Supply
        2. 7.3.1.2  Media Independent Interface (MAC side)
          1. 7.3.1.2.1 Common Platform Ethernet Switch 3-Port Gigabit (CPSW3G)
          2. 7.3.1.2.2 Programmable Real-Time Unit and Industrial Communication Subsystem - Gigabit (PRU_ICSSG)
          3. 7.3.1.2.3 Additional Information
        3. 7.3.1.3  Usage of SysConfig-PinMux Tool
        4. 7.3.1.4  EPHY Reset
        5. 7.3.1.5  Ethernet PHY Pin Strapping
        6. 7.3.1.6  Ethernet PHY (and MAC) Operation and Media Independent Interface (MII) Clock
          1. 7.3.1.6.1 Crystal
          2. 7.3.1.6.2 Oscillator
          3. 7.3.1.6.3 Processor Clock Output (CLKOUT0)
        7. 7.3.1.7  MAC (Data, Control and Clock) Interface Signals Termination
        8. 7.3.1.8  MAC (Media Access Controller) to MAC Interface
        9. 7.3.1.9  Management Data Input/Output (MDIO) Interface
          1. 7.3.1.9.1 MDIO Interface Mode
        10. 7.3.1.10 Ethernet Medium Dependent Interface (MDI) Including Magnetics
        11. 7.3.1.11 Capacitors for the Power Supply Rails
      2. 7.3.2 Universal Serial Bus (USB2.0)
        1. 7.3.2.1 USB Used
          1. 7.3.2.1.1 USB Host Interface
          2. 7.3.2.1.2 USB Device Interface
          3. 7.3.2.1.3 USB Dual-Role Device Interface
          4. 7.3.2.1.4 USB Type-C
        2. 7.3.2.2 USB Not Used
        3. 7.3.2.3 Additional Information
      3. 7.3.3 Serializer/Deserializer (SERDES)
        1. 7.3.3.1 SERDES0 Used
          1. 7.3.3.1.1 USB3SS0 - USB3.0 Super Speed Interface Configuration
            1. 7.3.3.1.1.1 Signal Interface
              1. 7.3.3.1.1.1.1 USB3.0 Super Speed Interface
                1. 7.3.3.1.1.1.1.1 USB3.0 Super Speed Interface Operating Mode Configuration
            2. 7.3.3.1.1.2 Unused SERDES Clock Termination
            3. 7.3.3.1.1.3 Additional Information
          2. 7.3.3.1.2 Peripheral Component Interconnect Express (PCIe) Interface Configuration
            1. 7.3.3.1.2.1 Clock Configuration for PCIe Operating Modes
            2. 7.3.3.1.2.2 Signal Interface Termination
            3. 7.3.3.1.2.3 PCIe Clock (REFCLK) Source
            4. 7.3.3.1.2.4 Hardware Reset (Fundamental Reset)
            5. 7.3.3.1.2.5 PCIe Clock Request (PCIE0_CLKREQn) Signal
            6. 7.3.3.1.2.6 Connecting PCIe Interface Signals
        2. 7.3.3.2 SERDES0 Not Used
      4. 7.3.4 Universal Asynchronous Receiver/Transmitter (UART)
      5. 7.3.5 Controller Area Network (CAN)
    4. 7.4 On-Board Synchronous Communication Interface (MCSPI and I2C)
      1. 7.4.1 Multichannel Serial Peripheral Interface (MCSPI)
      2. 7.4.2 Inter-Integrated Circuit (I2C)
    5. 7.5 Analog to Digital Converter (ADC)
      1. 7.5.1 ADC0 Used
      2. 7.5.2 ADC0 Not Used
    6. 7.6 GPIO and Hardware Diagnostics
      1. 7.6.1 General Purpose Input/Output (GPIO)
        1. 7.6.1.1 Termination and External Buffering
        2. 7.6.1.2 GPIO Multiplexed With MMC Interface
        3. 7.6.1.3 Additional Information
      2. 7.6.2 Internal Hardware Diagnostics
        1. 7.6.2.1 Monitoring of On-Board Supply Voltages Using Processor
          1. 7.6.2.1.1 Voltage Monitor Pins When Used
          2. 7.6.2.1.2 Voltage Monitor Pins Not Used
        2. 7.6.2.2 Internal Temperature Monitoring
        3. 7.6.2.3 Termination of Error Signal Output (MCU_SAFETY_ERRORn)
        4. 7.6.2.4 High Frequency Oscillator (MCU_OSC0) Clock Loss Detection
    7. 7.7 Verifying Board Level Design Issues
      1. 7.7.1 Processor Pin Configuration Using Pinmux Tool
      2. 7.7.2 Schematics Configurations
      3. 7.7.3 Terminations
      4. 7.7.4 Peripheral (Sub System) Clock Outputs
      5. 7.7.5 General Debug
        1. 7.7.5.1 Clock Output for Board Bring-Up, Test or Debug
        2. 7.7.5.2 Additional Information
  11. 8 Layout Notes (to be Added on the Schematic)
  12. 9 Board Design Simulation
  13. 10Additional References
  14. 11Summary
  15. 12References
    1. 12.1 AM64x
    2. 12.2 AM243x
    3. 12.3 Common
  16.   A Terminology
  17.   Revision History

A Terminology

ADC – Analog-to-Digital Converter

BOM – Bill of Materials

CAN – Controller Area Network

CKE – Clock Enable

CPPI – Communications Port Programming Interface

CPSW3G – Common Platform Ethernet Switch 3-port Gigabit

DFU – Device Firmware Upgrade

DNI – Do Not Install

DRD – Dual-Role Device

DRP – Dual Role Port

E2E – Engineer to Engineer

EMC – Electromagnetic Compatibility

EMI – Electromagnetic Interference

eMMC – embedded Multi-Media Card

EMU – Emulation Control

ESD – Electrostatic discharge

ESL – Effective Series Inductance

ESR – Effective Series Resistance

FET – Field-Effect Transistor

GPIO – General Purpose Input/Output

GPMC – General-Purpose Memory Controller

I2C – Inter-Integrated Circuit

JTAG – Joint Test Action Group

LDO – Low Dropout

LVCMOS – Low voltage complementary metal oxide semiconductor

MAC – Media Access Controller

MCSPI – Multichannel Serial Peripheral Interface

MDI – Medium Dependent Interface

MDIO – Management Data Input/Output

MII – Media Independent Interface

MMC – Multi-Media Card

MMCSD – Multi-Media Card/Secure Digital

ODT – On-die Termination

OSPI – Octal Serial Peripheral Interface

OTP – One-Time-Programmable

PCB – Printed Circuit Board

PCIe – Peripheral Component Interconnect Express

PDN – Power Distribution Network

PET – Power Estimation Tool

PMIC – Power management integrated circuit

POR – Power-on Reset

PRU_ICSSG – Programmable Real-Time Unit and Industrial Communication Subsystem - Gigabit

QSPI – Quad Serial Peripheral Interface

RGMII – Reduced Gigabit Media Independent Interface

RMII – Reduced Media Independent Interface

ROC – Recommended Operating Condition

SD – Secure Digital

SDIO – Secure Digital Input Output

SPI – Serial Peripheral Interface

TCK – JTAG Test Clock Input

TDI – JTAG Test Data Input

TDO – JTAG Test Data Output

TEN – Test Enable

TMS – JTAG Test Mode Select Input

TRM – Technical Reference Manual

TRSTn – JTAG Reset

UART – Universal Asynchronous Receiver/Transmitter

USB – Universal Serial Bus

XDS – eXtended Development System