SPRACZ7 January   2022 TMS320F28075 , TMS320F28075-Q1 , TMS320F28076 , TMS320F28232 , TMS320F28232-Q1 , TMS320F28234 , TMS320F28234-Q1 , TMS320F28235 , TMS320F28235-Q1 , TMS320F28332 , TMS320F28333 , TMS320F28334 , TMS320F28335 , TMS320F28335-Q1 , TMS320F28374D , TMS320F28374S , TMS320F28375D , TMS320F28375S , TMS320F28375S-Q1 , TMS320F28376D , TMS320F28376S , TMS320F28377D , TMS320F28377D-EP , TMS320F28377D-Q1 , TMS320F28377S , TMS320F28377S-Q1 , TMS320F28378D , TMS320F28378S , TMS320F28379D , TMS320F28379D-Q1 , TMS320F28379S

 

  1.   Trademarks
  2. 1 Introduction
    1. 1.1 Abbreviations
  3. 2 Central Processing Unit (CPU)
  4. 3 Development Tools
    1. 3.1 Driver Library (Driverlib)
    2. 3.2 Embedded Application Binary Interface (EABI) Support
  5. 4 Package and Pinout
  6. 5 Operating Frequency and Power Management
  7. 6 Power Sequencing
  8. 7 Input Clock Options
  9. 8 Memory Map
  10. 9 Flash and OTP
    1. 9.1 Size and Number of Sectors
    2. 9.2 Flash Parameters
    3. 9.3 Flash Programming
    4. 9.4 Entry Point into Flash
    5. 9.5 Dual Code Security Module (DCSM) and Password Locations
    6. 9.6 OTP
  11. 10Boot ROM
    1. 10.1 Boot ROM Reserved RAM
    2. 10.2 Boot Mode Selection
    3. 10.3 Bootloaders
  12. 11Architectural Enhancements
    1. 11.1 Clock Sources and Domains
    2. 11.2 Watchdog Timer
    3. 11.3 Peripheral Interrupt Expansion (PIE)
    4. 11.4 Lock Protection Registers
    5. 11.5 General-Purpose Input/Output (GPIO)
    6. 11.6 External Interrupts
    7. 11.7 Crossbar (X-BAR)
  13. 12Peripherals
    1. 12.1 New Peripherals
      1. 12.1.1 Analog Subsystem Interconnect
      2. 12.1.2 Comparator Subsystem (CMPSS)
      3. 12.1.3 Control Law Accelerator (CLA)
    2. 12.2 Control Peripherals
      1. 12.2.1 Enhanced Pulse Width Modulator (ePWM)
      2. 12.2.2 Enhanced Capture Module (eCAP)
      3. 12.2.3 Enhanced Quadrature Encode Pulse Module (eQEP)
      4. 12.2.4 Sigma-Delta Filter Module (SDFM)
    3. 12.3 Analog Peripherals
      1. 12.3.1 Analog-to-Digital Converter (ADC)
    4. 12.4 Communication Peripherals
      1. 12.4.1 SPI
      2. 12.4.2 SCI
      3. 12.4.3 USB
      4. 12.4.4 I2C
      5. 12.4.5 CAN
  14. 13Configurable Logic Block (CLB)
  15. 14Device Comparison Summary
  16. 15References

2 Central Processing Unit (CPU)

The F2837xD/S/07x devices extend the capabilities of the existing TI C28x 32-bit fixed-point CPU architecture by adding a trigonometric math unit (TMU) and a Viterbi/Complex Math Unit (VCU-II). No changes have been made to existing instructions, pipeline, or memory bus architecture and programs written for the C28x CPU are completely compatible with these architectural enhancements.

The Trigonometric Math Unit (TMU) is an extension of the FPU and the C28x instruction set, and it efficiently executes trigonometric and arithmetic operations commonly found in control system applications. Similar to the FPU, the TMU provides hardware support for IEEE-754 single-precision floating-point operations. Seamless code integration is accomplished by built-in compiler support that automatically generates TMU instructions where applicable. This dramatically increases the performance of trigonometric functions, which would otherwise be very cycle intensive. All TMU instructions use the existing FPU register set (R0H to R7H) to carry out their operations. Since the TMU uses the same register set and flags as the FPU, there are no special considerations relating to interrupt context save and restore.

The VCU-II is the second-generation Viterbi, Complex Math, and CRC extension to the C28x CPU. The VCU-II extends the capabilities of the C28x CPU by adding registers and instructions to accelerate the performance of FFTs and communications-based algorithms such as Viterbi decoding and Cyclic Redundancy Check.

The C28x CPU, FPU, TMU and VCU architecture and instruction set are documented in the following reference guides: