SPRUIY1D November   2020  – August 2024

 

  1.   1
  2.   Description
  3.   Features
  4.   4
  5. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Preface: Read This First
      1. 1.2.1 If You Need Assistance
      2. 1.2.2 Important Usage Notes
    3. 1.3 Kit Overview
      1. 1.3.1 Kit Contents
      2. 1.3.2 Key Features
      3. 1.3.3 Component Identification
      4. 1.3.4 Daughter Cards
        1. 1.3.4.1 Connecting the AM273x EVM to the AWR2243BOOST EVM
        2. 1.3.4.2 Connecting the AM273x EVM to the DCA1000
      5. 1.3.5 Security
      6. 1.3.6 Compliance
  6. 2Hardware
    1. 2.1 Board Setup
      1. 2.1.1 Power Requirements
        1. 2.1.1.1 Power Status LEDs
      2. 2.1.2 Push Buttons
      3. 2.1.3 Switches
      4. 2.1.4 LEDs
      5. 2.1.5 Boot Mode Selection
    2. 2.2 Hardware Description
      1. 2.2.1  Functional Block Diagram
      2. 2.2.2  Memory Interface
        1. 2.2.2.1 QSPI Interface
        2. 2.2.2.2 Board ID EEPROM
      3. 2.2.3  Ethernet Interface
      4. 2.2.4  Micro USB Interfaces
        1. 2.2.4.1 FTDI USB Interface
          1. 2.2.4.1.1 FTDI EEPROM Memory Device
        2. 2.2.4.2 XDS USB Interface
        3. 2.2.4.3 PC Connection
      5. 2.2.5  I2C Interface
        1. 2.2.5.1 I2C Connections
      6. 2.2.6  UART Interface
      7. 2.2.7  CAN Interfaces
        1. 2.2.7.1 CAN-A Interface
        2. 2.2.7.2 CAN-B Interface
      8. 2.2.8  JTAG Emulation
      9. 2.2.9  SPI Interface
      10. 2.2.10 MDI Interface
      11. 2.2.11 ePWM Interface
    3. 2.3 Connectors
      1. 2.3.1 60-Pin High Density (HD) FE Connector-1 (J1)
      2. 2.3.2 60-Pin High Density (HD) FE Connector-2 (J11)
      3. 2.3.3 MIPI 60-Pin Connector (J19)
      4. 2.3.4 Debug Connector 60-Pin (J7)
      5. 2.3.5 External Clock Option (J13, J1)
    4. 2.4 Mechanical Mounting of the PCB
  7. 3Additional Information
    1. 3.1 Trademarks
    2.     3.A Rev. C Design Changes
  8. 4Revision History

2.3.3 MIPI 60-Pin Connector (J19)

This connector provides the standard MIPI 60-pin interface for JTAG and trace capability through emulators such as the XDS560pro. Further information on the emulation and trace header can be found in the Emulation and Trace Headers Technical Reference Manual.

To use this interface, the JTAG lines from the TMDS273GPEVM must be muxed to MIPI 60-pin connector.


TMDS273EVM, TMDS273GPEVM, TPR12REVM MIPI 60 Connector Schematic

Figure 2-27 MIPI 60 Connector Schematic
Table 2-13 J19 Connector Pin
Pin Number Description Pin Number Description
1 MIPI_VREF 2 MIPI_TMS
3 MIPI_TCK 4 MIPI_TDO
5 MIPI_TDI 6 MIPI_NRST
7 MIPI_RTCK 8 MIPI_TRSTPD
9 MIPI_JTAG_NRST 10 NC
11 NC 12 MIPI_VREF
13 MIPI_TRACE_CLK 14 NC
15 MIPI_DBG_DETECT 16 GND
17 MIPI_TRACE_CTL 18 NC
19 MIPI_TRACE0 20 NC
21 MIPI_TRACE1 22 NC
23 MIPI_TRACE2 24 NC
25 MIPI_TRACE3 26 NC
27 MIPI_TRACE4 28 NC
29 MIPI_TRACE5 30 NC
31 MIPI_TRACE6 32 NC
33 MIPI_TRACE7 34 NC
35 MIPI_TRACE8 36 NC
37 MIPI_TRACE9 38 NC
39 MIPI_TRACE10 40 NC
41 MIPI_TRACE11 42 NC
43 MIPI_TRACE12 44 NC
45 MIPI_TRACE13 46 NC
47 MIPI_TRACE14 48 NC
49 MIPI_TRACE15 50 NC
51 NC 52 NC
53 NC 54 NC
55 NC 56 NC
57 GND 58 GND
59 NC 60 NC