SPRUJ85A April   2024  – August 2024

PRODUCTION DATA  

  1.   1
  2.   Description
  3. 1Key Features
  4. 2LaunchPad Module Overview
    1. 3.1 Introduction
    2. 3.2 Preface: Read This First
      1. 3.2.1 If You Need Assistance
      2. 3.2.2 Important Usage Notes
    3. 3.3 Kit Contents
    4. 3.4 Device Information
      1. 3.4.1 System Architecture Overview
      2. 3.4.2 Security
      3. 3.4.3 Compliance
      4. 3.4.4 BoosterPacks
      5. 3.4.5 Component Identification
  5. 3Hardware Description
    1. 4.1  Board Setup
      1. 4.1.1 Power Requirements
        1. 4.1.1.1 Power Input Using USB Type-C Connector
        2. 4.1.1.2 Power Status LEDs
        3. 4.1.1.3 Power Tree
      2. 4.1.2 Push Buttons
      3. 4.1.3 Boot mode Selection
      4. 4.1.4 IO Expander
    2. 4.2  Functional Block Diagram
    3. 4.3  GPIO Mapping
    4. 4.4  Reset
    5. 4.5  Clock
    6. 4.6  Memory Interfaces
      1. 4.6.1 OSPI
      2. 4.6.2 MMC
      3. 4.6.3 eMMC
      4. 4.6.4 Board ID EEPROM
    7. 4.7  Ethernet Interface
      1. 4.7.1 Ethernet PHY #1 - CPSW RGMII/ICSSM
      2. 4.7.2 Ethernet PHY #2 - CPSW RGMII/ICSSM
      3. 4.7.3 LED Indication in RJ45 Connector
    8. 4.8  I2C
    9. 4.9  Industrial Application LEDs
    10. 4.10 SPI
    11. 4.11 UART
    12. 4.12 MCAN
    13. 4.13 FSI
    14. 4.14 JTAG
    15. 4.15 TIVA and Test Automation Header
    16. 4.16 LIN
    17. 4.17 ADC and DAC
    18. 4.18 EQEP and SDFM
    19. 4.19 EPWM
    20. 4.20 BoosterPack Headers
    21. 4.21 Pinmux Mapping
  6. 4Additional Information
    1.     Trademarks
    2. 5.1 Sitara MCU+ Academy
    3. 5.2 Known Board Changes/Issues
      1. 5.2.1 OSPI DQS and LBCLK nets swap
      2. 5.2.2 XDS110 Debugger Bricking Issue
      3. 5.2.3 eMMC CMD and CLK nets swap
  7. 5References
    1. 6.1 Reference Documents
    2. 6.2 Other TI Components Used in This Design
  8. 6Revision History

2.4.2 Security

The AM263Px LaunchPad features a High Security, Field Securable (HS-FS) device. An HS-FS device has the ability to use a one time programming to convert the device from HS-FS to High Security, Security Enforced (HS-SE) device.

The AM263Px device leaves the TI factory in an HS-FS state where customer keys are not programmed and has the following attributes:

  • Does not enforce the secure boot process
  • M4 JTAG port is closed
  • R5 JTAG port is open
  • Security Subsystem firewalls are closed
  • SoC Firewalls are open
  • ROM Boot expects a TI signed binary (encryption is optional)
  • TIFS-MCU binary is signed by the TI private key

The One Time Programmable (OTP) keywriter converts the secure device from HS-FS to HS-SE. The OTP keywriter programs customer keys into the device efuses to enforce secure boot and establish a root of trust. The secure boot requires an image to be encrypted (optional) and signed using customer keys, which will be verified by the SoC. A secure device in the HS-SE state has the following attributes:

  • M4, R5 JTAG ports are both closed
  • Security Subsystems and SoC Firewalls are both closed
  • TIFS-MCU and SBL need to be signed with active customer key