SPRUJA2 November   2023

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   5
  6. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Device Information
    4. 1.4 Specification
  7. 2Hardware
    1. 2.1  Additional Images
    2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Supported Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers
    3. 2.3  Interface Mapping
    4. 2.4  Power ON/OFF Procedure
      1. 2.4.1 Power ON Procedure
      2. 2.4.2 Power OFF Procedure
      3. 2.4.3 Test Points
    5. 2.5  Clocking
      1. 2.5.1 Peripheral Ref Clock
    6. 2.6  Reset
    7. 2.7  CSI Interface
    8. 2.8  OLDI Interface
    9. 2.9  DSI Interface
    10. 2.10 Audio Codec Interface
    11. 2.11 HDMI Display Interface
    12. 2.12 JTAG Interface
    13. 2.13 Test Automation Header
    14. 2.14 UART Interface
    15. 2.15 USB Interface
      1. 2.15.1 USB 2.0 Type A Interface
      2. 2.15.2 USB 2.0 Type C Interface
    16. 2.16 Memory Interfaces
      1. 2.16.1 LPDDR4 Interface
      2. 2.16.2 OSPI Interface
      3. 2.16.3 MMC Interfaces
        1. 2.16.3.1 MMC0 - eMMC Interface
        2. 2.16.3.2 MMC1 - Micro SD Interface
        3. 2.16.3.3 MMC2 - M.2 Key E Interface
      4. 2.16.4 Board ID EEPROM
    17. 2.17 Ethernet Interface
      1. 2.17.1 CPSW Ethernet PHY Strapping
      2. 2.17.2 CPSW Ethernet PHY1 Default Configuration
      3. 2.17.3 CPSW Ethernet PHY2 Default Configuration
    18. 2.18 GPIO Port Expander
    19. 2.19 GPIO Mapping
    20. 2.20 Power
      1. 2.20.1 Power Requirement
      2. 2.20.2 Power Input
      3. 2.20.3 Power Supply
      4. 2.20.4 Power Sequencing
      5. 2.20.5 AM62P SoC Power
      6. 2.20.6 Current Monitoring
    21. 2.21 EVM User Setup/Configuration
      1. 2.21.1 DIP Switches
      2. 2.21.2 Boot Modes
      3. 2.21.3 User Test LEDs
    22. 2.22 Expansion Headers
      1. 2.22.1 User Expansion Connector
      2. 2.22.2 MCU Connector
      3. 2.22.3 GPMC NAND (x8) Connector
    23. 2.23 Interrupt
    24. 2.24 I2C Address Mapping
  8. 3Hardware Design Files
  9. 4Compliance Information
    1. 4.1 Compliance and Certifications
  10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
      1. 5.1.1 Issue 1 - Watchdog Reset
      2. 5.1.2 Issue 2 - Power Down Sequence
    2. 5.2 Trademarks

2.3 Interface Mapping

Table 2-1 Interface Mapping
Interface Name Port on SoC Device Part Number
Memory – LPDDR4 DDR0 MT53E2G32D4DE-046 AUT:C
Memory – OSPI OSPI0 S28HS512TGABHM010
Memory – Micro SD socket MMC1 MEM2051-00-195-00-A
Memory – eMMC MMC0 MTFC32GAZAQHD-IT
Memory – Board ID EEPROM SoC_I2C0 AT24C512C-MAHM-T
Ethernet 1 – RGMII SoC_RGMII1 DP83867IRRGZ
Ethernet 2 – RGMII SoC_RGMII2 DP83867IRRGZ
GPIO port expander 1 SoC_I2C1 TCA6424ARGJR
User expansion connector – 2x20 HDR SPI0, SPI2, UART5, SoC_I2C0, SoC_I2C2, McASP1 and GPIOs PEC20DAAN
MCU header – 2x14 HDR MCU MCU_UART0, MCU_MCAN0, MCU_SPI0, MCU_I2C0 and MCU GPIOs PREC014DAAN-RC
GPMC NAND (x8) HDR G GPMC PREC010DAAN-RC
USB– 2.0 Type C USB0 2012670005
USB– 2.0 Type A USB1 629104151021
CSI interface CSI0-RX 52435-2271
DSI interface DSI0-TX 5019512230
OLDI interface OLDI 5019514030
MCAN1 interface MCAN1 TSM-103-02-T-SV
HDMI VOUT0, McASP1and SoC_I2C1 SiI9022ACNU + TPD12S016PWR + DC04S019JA1R600
Audio codec McASP1 and SoC_I2C1 TLV320AIC3106IRGZT+ SJ-43514-SM
GPIO port expander 2 SoC_I2C1 TCA6424ARGJR
UART terminal (UART-to-USB) SoC_UAR SoC_UART[1:0], WKUP_UART0 and MCU_UART0 FT4232HL + 629105150521
Test automation header SoC_I2C1 FH12A-40S-0.5SH
Temperature sensors SoC_I2C1 TMP100NA/3K
Current monitors SoC_I2C1 INA228AIDGSR
Connectivity– M.2 Key E MMC2, McASP1 and SoC_UART1 2199119-4