SPRUJA2 November   2023

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   5
  6. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Device Information
    4. 1.4 Specification
  7. 2Hardware
    1. 2.1  Additional Images
    2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Supported Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers
    3. 2.3  Interface Mapping
    4. 2.4  Power ON/OFF Procedure
      1. 2.4.1 Power ON Procedure
      2. 2.4.2 Power OFF Procedure
      3. 2.4.3 Test Points
    5. 2.5  Clocking
      1. 2.5.1 Peripheral Ref Clock
    6. 2.6  Reset
    7. 2.7  CSI Interface
    8. 2.8  OLDI Interface
    9. 2.9  DSI Interface
    10. 2.10 Audio Codec Interface
    11. 2.11 HDMI Display Interface
    12. 2.12 JTAG Interface
    13. 2.13 Test Automation Header
    14. 2.14 UART Interface
    15. 2.15 USB Interface
      1. 2.15.1 USB 2.0 Type A Interface
      2. 2.15.2 USB 2.0 Type C Interface
    16. 2.16 Memory Interfaces
      1. 2.16.1 LPDDR4 Interface
      2. 2.16.2 OSPI Interface
      3. 2.16.3 MMC Interfaces
        1. 2.16.3.1 MMC0 - eMMC Interface
        2. 2.16.3.2 MMC1 - Micro SD Interface
        3. 2.16.3.3 MMC2 - M.2 Key E Interface
      4. 2.16.4 Board ID EEPROM
    17. 2.17 Ethernet Interface
      1. 2.17.1 CPSW Ethernet PHY Strapping
      2. 2.17.2 CPSW Ethernet PHY1 Default Configuration
      3. 2.17.3 CPSW Ethernet PHY2 Default Configuration
    18. 2.18 GPIO Port Expander
    19. 2.19 GPIO Mapping
    20. 2.20 Power
      1. 2.20.1 Power Requirement
      2. 2.20.2 Power Input
      3. 2.20.3 Power Supply
      4. 2.20.4 Power Sequencing
      5. 2.20.5 AM62P SoC Power
      6. 2.20.6 Current Monitoring
    21. 2.21 EVM User Setup/Configuration
      1. 2.21.1 DIP Switches
      2. 2.21.2 Boot Modes
      3. 2.21.3 User Test LEDs
    22. 2.22 Expansion Headers
      1. 2.22.1 User Expansion Connector
      2. 2.22.2 MCU Connector
      3. 2.22.3 GPMC NAND (x8) Connector
    23. 2.23 Interrupt
    24. 2.24 I2C Address Mapping
  8. 3Hardware Design Files
  9. 4Compliance Information
    1. 4.1 Compliance and Certifications
  10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
      1. 5.1.1 Issue 1 - Watchdog Reset
      2. 5.1.2 Issue 2 - Power Down Sequence
    2. 5.2 Trademarks

2.4.3 Test Points

Test points for each power output on the board are mentioned in Table 3-2.

Table 2-2 Test Points
SL. No. Power Supply Test Point Voltage
1 VCC5V0_EXP TP10 5
2 VDD_CANUART TP11 0.85
3 VCC3V3_EXP TP12 3.3
4 VDD_1V0 TP23 1
5 VDD_1V2 TP24 1.2
6 VDDSHV_SDIO TP33 3.3/1.8
7 VPP_1V8 TP35 1.8
8 VDD_2V5 TP36 2.5
9 VDD_CORE TP42 0.85/0.75
10 VDDR_CORE TP43 0.85
11 VCC1V8_SYS TP54 1.8
12 VDDA_1V8 TP55 1.8
13 VDD_LPDDR4 TP56 1.1
14 VCC_3V3_SYS TP61 3.3
15 VCC_3V3_MAIN TP68 3.3
16 VMAIN TP82 12
17 VCC_5V0 TP85 5
18 VCC3V3_XDS TP90 3.3
19 XDS_USB_VBUS TP98 5
20 VCC3V3_TA TP201 3.3
21 VBUS_5V0_TYPEA TP203 5
22 VBUS_TYPEC1 TP204 12
23 VBUS_TYPEC2 TP205 12
24 FT4232_USB_VBUS TP206 5
25 LDO_3V3 U30.8 3.3
26 VCC_3V3_FT4232 C153.2 3.3
27 VDD_MMC1_SD TP202 3.3
28 VCC_5V0_HDMICONN TP207 5