SPRUJA2 November   2023

1.   1
2.   Description
3.   Get Started
4.   Features
5.   5
6. 1Evaluation Module Overview
   1. 1.1 Introduction
   2. 1.2 Kit Contents
   3. 1.3 Device Information
   4. 1.4 Specification
7. 2Hardware
   1. 2.1  Additional Images
   2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Supported Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers
   3. 2.3  Interface Mapping
   4. 2.4  Power ON/OFF Procedure
      1. 2.4.1 Power ON Procedure
      2. 2.4.2 Power OFF Procedure
      3. 2.4.3 Test Points
   5. 2.5  Clocking
      1. 2.5.1 Peripheral Ref Clock
   6. 2.6  Reset
   7. 2.7  CSI Interface
   8. 2.8  OLDI Interface
   9. 2.9  DSI Interface
   10. 2.10 Audio Codec Interface
   11. 2.11 HDMI Display Interface
   12. 2.12 JTAG Interface
   13. 2.13 Test Automation Header
   14. 2.14 UART Interface
   15. 2.15 USB Interface
       1. 2.15.1 USB 2.0 Type A Interface
       2. 2.15.2 USB 2.0 Type C Interface
   16. 2.16 Memory Interfaces
       1. 2.16.1 LPDDR4 Interface
       2. 2.16.2 OSPI Interface
       3. 2.16.3 MMC Interfaces
          1. 2.16.3.1 MMC0 - eMMC Interface
          2. 2.16.3.2 MMC1 - Micro SD Interface
          3. 2.16.3.3 MMC2 - M.2 Key E Interface
       4. 2.16.4 Board ID EEPROM
   17. 2.17 Ethernet Interface
       1. 2.17.1 CPSW Ethernet PHY Strapping
       2. 2.17.2 CPSW Ethernet PHY1 Default Configuration
       3. 2.17.3 CPSW Ethernet PHY2 Default Configuration
   18. 2.18 GPIO Port Expander
   19. 2.19 GPIO Mapping
   20. 2.20 Power
       1. 2.20.1 Power Requirement
       2. 2.20.2 Power Input
       3. 2.20.3 Power Supply
       4. 2.20.4 Power Sequencing
       5. 2.20.5 AM62P SoC Power
       6. 2.20.6 Current Monitoring
   21. 2.21 EVM User Setup/Configuration
       1. 2.21.1 DIP Switches
       2. 2.21.2 Boot Modes
       3. 2.21.3 User Test LEDs
   22. 2.22 Expansion Headers
       1. 2.22.1 User Expansion Connector
       2. 2.22.2 MCU Connector
       3. 2.22.3 GPMC NAND (x8) Connector
   23. 2.23 Interrupt
   24. 2.24 I2C Address Mapping
8. 3Hardware Design Files
9. 4Compliance Information
   1. 4.1 Compliance and Certifications
10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
       1. 5.1.1 Issue 1 - Watchdog Reset
       2. 5.1.2 Issue 2 - Power Down Sequence
    2. 5.2 Trademarks