SWRA751 September   2022

 

  1.   Introduction
  2.   Trademarks
  3. 1Command Packet
  4. 2Event Packet
  5. 3HCI Commands
    1. 3.1 HCI Commands List Format
    2. 3.2 Support HCI Commands Detailed Description
      1. 3.2.1  HCI_VS_Write_BD_Addr (0xFC06)
      2. 3.2.2  HCI_VS_Write_CODEC_Config (0xFD06)
      3. 3.2.3  HCI_VS_Write_CODEC_Config_Enhanced (0xFD07)
      4. 3.2.4  HCI_VS_DRP_Read_BER_Meter_Result (0xFD13)
      5. 3.2.5  HCI_VS_DRPb_Tester_Con_RX (0xFD17)
      6. 3.2.6  HCI_VS_LE_Enable (0xFD5B)
      7. 3.2.7  HCI_VS_Set_LE_Test_Mode_Parameters (0xFD77)
      8. 3.2.8  HCI_VS_DRPb_Enable_RF_Calibration (0xFD80)
      9. 3.2.9  HCI_VS_DRPb_Tester_Con_TX (0xFD84)
      10. 3.2.10 HCI_VS_DRPb_Tester_Packet_TX_RX (0xFD85)
      11. 3.2.11 HCI_VS_DRPb_Reset (0xFD88)
      12. 3.2.12 HCI_VS_DRPb_BER_Meter_Start (0xFD8B)
      13. 3.2.13 HCI VS LE Read Ber Test Results (0xFDAE)
      14. 3.2.14 HCI_VS_Read_RSSI (0xFDFC)
      15. 3.2.15 HCI_VS_Write_SCO_Configuration (0xFE10)
      16. 3.2.16 HCI_VS_Set_Pcm_Loopback_Enable (0xFE28)
      17. 3.2.17 HCI_VS_Read_Hardware_Register (0xFF00)
      18. 3.2.18 HCI_VS_Write_Hardware_Register (0xFF01)
      19. 3.2.19 HCI_VS_Update_UART_HCI_Baudrate (0xFF36)
      20. 3.2.20 HCI_VS_Set_Supported_Features (0xFF26)
      21. 3.2.21 HCI_VS_HCILL_Parameters (0xFD2B)
      22. 3.2.22 HCI_VS_Sleep_Mode_Configurations (0xFD0C)
      23. 3.2.23 HCI_VS_Get_System_Status (0xFE1F)
      24. 3.2.24 HCI_VS_Read_Patch_Version (0xFF22)
      25. 3.2.25 HCI_VS_DRPb_Set_Power_Vector (0xFD82)
      26. 3.2.26 HCI_VS_DRPb_Set_Class2_Single_Power (0xFD87)
      27. 3.2.27 HCI_VS_LE_Output_Power (0xFDDD)
      28. 3.2.28 HCI_VS_A3DP_Codec_Configuration (0xFD8E)
      29. 3.2.29 HCI_VS_AVPR_Enable (0xFD92)
      30. 3.2.30 HCI_VS_A3DP_Open_Stream (0xFD8C)
      31. 3.2.31 HCI_VS_A3DP_Close_Stream (0xFD8D)
      32. 3.2.32 HCI_VS_A3DP_Start_Stream (0xFD8F)
      33. 3.2.33 HCI_VS_A3DP_Stop_Stream (0xFD90)
      34. 3.2.34 HCI_VS_A3DP_Sink_Codec_Configuration (0xFD9C)
      35. 3.2.35 HCI_VS_A3DP_Sink_Open_Stream (0xFD9A)
      36. 3.2.36 HCI_VS_A3DP_Sink_Close_Stream (0xFD9B)
      37. 3.2.37 HCI_VS_A3DP_Sink_Start_Stream (0xFD9D)
      38. 3.2.38 HCI_VS_A3DP_Sink_Stop_Stream (0xFD9E)
      39. 3.2.39 HCI_VS_WBS_Associate (0xFD78)
      40. 3.2.40 HCI_VS_WBS_Disassociate (0xFD79)
  6. 4General Hardware Errors
  7. 5Revision History

3.2.10 HCI_VS_DRPb_Tester_Packet_TX_RX (0xFD85)

Description:

This command starts sending/receiving packets using packet transmission parameters such as frequency channel, packet type, and packet length. It is used for Packet TX/RX.

Table 3-21 Command Parameters HCI_VS_DRPb_Tester_Packet_TX_RX (0xFD85) Frequency mode, TX single-frequency index, RX single-frequency, ACL packet type, ACL packet data pattern, Reserved, ACL packet data length, Power level, Disable whitening, PRBS9 initialization value
Command Parameter Size (bytes) Value Description
Frequency mode 1

0x00

0x03

Hopping

Single frequency
TX single-frequency 1 0 - 78 Selects Bluetooth frequency channel for transmission. Frequency channel index (k), range 0 – 78 (decimal)
 Freq = 2402 + 2k, for k = 0, 1, 2 … 39
Freq = 2403 + 2(k–40), for k = 40, 41…78
RX single-frequency 1 0 - 78, 0xFF Selects Bluetooth frequency channel for transmission. Frequency channel index (k), range 0 – 78 (decimal)
 Freq = 2402 + 2k, for k = 0, 1, 2 … 39
Freq = 2403 + 2(k–40), for k = 40, 41…78
0xFF – Disable RX (packet TX only)
ACL packet type 1 0x000x010x020x030x040x050x060x070x080x090x0A0x0B DM1DH1DM3DH3DM5DH52-DH12-DH32-DH53-DH13-DH33-DH5
ACL packet data pattern 1

0x00

0x01

0x02

0x03

0x04

0x05

All 0

All 1

5555 (0101 0101 0101 0101b)

FOFO (1111 0000 1111 0000b)

Ordered

PRBS9 random
Reserved 1 0xXX Reserved (Default: 0x00)
ACL packet data length 2

0-17

0-27

0-121

0-183

0-224

0-339

0-54

0-367

0–679

0-83

0–552

0-1021

DM1

DH1

DM3

DH3

DM5

DH5

2-DH1

2-DH3

2-DH5

3-DH1

3-DH3

3-DH5
Power level 1 0 - 15 15 = Max Output Power, 0 = Min Output Power
Disable whitening 1

0x00

0x01

Enable whitening

Disable whitening
PRBS9 initialization value 2 0x0000 - 0x01FF Used only in PRBS9 patterns to initialize PRBS9 data
Table 3-22 Return Parameters
Returned Value Description Size (bytes) Events Generated
0x00
0x01 – 0xFF		 Command succeeded.
Command failed.		 1 Command Complete