Calculation tool
Data sheet
LM73606
- New product available: LM61460 60-V, 6-A synchronous converter
- Synchronous rectification
- Wettable flanks QFN package (WQFN)
- Low quiescent current
- 0.8 µA in shutdown (typical)
- 15 µA in active mode with no load (typical)
- Wide voltage conversion range:
- tON-MIN = 60 ns (typical)
- tOFF-MIN = 70 ns (typical)
- Low MOSFET ON-resistance:
- RDS_ON_HS = 53 mΩ (typical)
- RDS_ON_LS = 31 mΩ (typical)
- External bias input to improve efficiency
- Pin-selectable auto mode or forced PWM operation
- Adjustable frequency range: 350 kHz to 2.2 MHz
- Synchronizable to external clock
- Internal compensation
- Power-good flag
- Precision enable to program system UVLO
- Flexible soft-start features:
- Start-up into pre-biased load
- Fixed or adjustable soft-start time
- Output voltage tracking
- Cycle-by-cycle current limiting
- Short-circuit protection with hiccup mode
- Create a custom design with the WEBENCH® power designer using LM73605 or LM73606
The LM73605 and LM73606 family of devices are easy-to-use synchronous step-down DC/DC converters capable of driving up to 5 A or 6 A of load current from a supply voltage ranging from 3.5 V to 36 V. The LM73605 and LM73606 provide exceptional efficiency and output accuracy in a very small solution size. Peak current-mode control is employed. Additional features such as adjustable switching frequency, synchronization to an external clock, power-good flag, precision enable, adjustable soft start, and tracking provide both flexible and easy-to-use solutions for a wide range of applications. Automatic frequency foldback at light load improves efficiency over the entire load range. Protection features include thermal shutdown, cycle-by-cycle current limiting, and short-circuit protection. The devices are pin-to-pin compatible for easy current scaling. The new product, LM61460-Q1, offers higher efficiency, lower stand-by quiescent current, and improved EMI performance. See the device comparison table to compare specifications. Start a Webench design with LM61460-Q1. Use the LMZM33606 module for faster time to market.
Technical documentation
No results found. Please clear your search and try again.
View all 6 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | LM73605/LM73606 3.5-V to 36-V, 5-A or 6-A Synchronous Step-Down Voltage Converter datasheet (Rev. A) | PDF | HTML | 21 Jul 2017 |
| Functional safety information | LM73606 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA | PDF | HTML | 12 Jul 2022 | |
| Selection guide | Buck Converter Quick Reference Guide (Rev. B) | 08 Apr 2021 | ||
| Test report | Automotive Wide-VIN to Point-of-Load Power Supply Reference Design (Rev. A) | 26 Mar 2020 | ||
| White paper | Power modules for lab instrumentation | 18 Oct 2018 | ||
| EVM User's guide | LM73605/LM73606 EVM User's Guide | 20 Sep 2017 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
LM73606EVM-5V-400K — LM73606 Synchronous Step-Down Converter Evaluation Module
The LM73606EVM-5V-400K evaluation module (EVM) is a fully assembled and tested circuit for evaluating the LM73606 synchronous step-down voltage converter. The EVM operates from 6V to 36V input and provides a 5V output voltage with 6A maximum load current.
User guide: PDF
Simulation model
LM73606 Non-Inverting and Inverting PSpice Transient Model
SNVMBE5.ZIP (240 KB) - PSpice Model
Simulation model
LM73606 Unencrypted Non-Inverting and Inverting PSpice Transient Model
SNVMBE4.ZIP (8 KB) - PSpice Model
Reference designs
PMP15023 — Automotive wide-VIN to point-of-load power supply with front-end circuit protection reference design
This automotive point-of-load power supply reference design features complete front-end protection in a small overall solution size. The system can clamp fast high-voltage electrical transients and maintain operation through these events. It can also properly respond to a reverse battery polarity (...)
Reference designs
TIDA-010011 — High efficiency power supply architecture reference design for protection relay processor module
This reference design showcases various power architectures for generating multiple voltage rails for an application processor module, requiring >1A load current and high efficiency . The required power supply is generated using 5-, 12- or 24-V DC input from the backplane. Power supplies are (...)
Reference designs
PMP40286 — Automotive USB Type-C™ DFP 5V 3A + USB Type-A 5V 2.4A Charger Reference Design
PMP40286 is a dual port car charger reference design. The output goes to a 5V 3A USB Type-C™ port and a 5V 2.4A USB type-A port. The USB Type-C port can be backwards compliant with BC1.2 and DCP configurations. The type-A port is capable of compensating for the effects on voltage droop (...)
Reference designs
PMP40285 — Automotive Dual Port USB Type-C™ DFP 5V 3A Charger Reference Design
PMP40285 is a dual port USB Type-C™ charger reference design. This design takes an automotive input voltage, the output goes to two USB Type-C port. Each of these ports supplies 5V 3A for USB Type-C™ device. The design is fully compliant with USB type C and backwards compliant with (...)
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| WQFN (RNP) | 30 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.