SLOSE98A December   2022  – September 2023 DRV8461

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
      1. 6.5.1 SPI Timing Requirements
      2. 6.5.2 STEP and DIR Timing Requirements
    6. 6.6 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Interface of Operation
      2. 7.3.2  Stepper Motor Driver Current Ratings
        1. 7.3.2.1 Peak Current Rating
        2. 7.3.2.2 RMS Current Rating
        3. 7.3.2.3 Full-Scale Current Rating
      3. 7.3.3  PWM Motor Drivers
      4. 7.3.4  Microstepping Indexer
      5. 7.3.5  Indexer Output
        1. 7.3.5.1 nHOME Output
      6. 7.3.6  Automatic Microstepping Mode
      7. 7.3.7  Custom Microstepping Table
      8. 7.3.8  Current Regulation
        1. 7.3.8.1 Internal Reference Voltage
      9. 7.3.9  Standstill Power Saving Mode
      10. 7.3.10 Current Regulation Decay Modes
        1. 7.3.10.1 Slow Decay
        2. 7.3.10.2 Mixed Decay
        3. 7.3.10.3 Smart tune Dynamic Decay
        4. 7.3.10.4 Smart tune Ripple Control
        5. 7.3.10.5 PWM OFF Time
        6. 7.3.10.6 Current Regulation Blanking Time and Deglitch Time
      11. 7.3.11 Current Sensing with External Resistor
      12. 7.3.12 Silent step decay mode
      13. 7.3.13 Auto-torque Dynamic Current Adjustment
        1. 7.3.13.1 Auto-torque Learning Routine
        2. 7.3.13.2 Current Control Loop
        3. 7.3.13.3 PD Control Loop
      14. 7.3.14 Charge Pump
      15. 7.3.15 Linear Voltage Regulator
      16. 7.3.16 VCC Voltage Supply
      17. 7.3.17 Logic Level, Tri-Level and Quad-Level Pin Diagrams
      18. 7.3.18 Spread Spectrum
      19. 7.3.19 Protection Circuits
        1. 7.3.19.1  VM Undervoltage Lockout
        2. 7.3.19.2  VCP Undervoltage Lockout (CPUV)
        3. 7.3.19.3  Logic Supply Power on Reset (POR)
        4. 7.3.19.4  Overcurrent Protection (OCP)
          1. 7.3.19.4.1 Latched Shutdown
          2. 7.3.19.4.2 Automatic Retry
        5. 7.3.19.5  Stall Detection
        6. 7.3.19.6  Open-Load Detection (OL)
        7. 7.3.19.7  Overtemperature Warning (OTW)
        8. 7.3.19.8  Thermal Shutdown (OTSD)
          1. 7.3.19.8.1 Latched Shutdown
          2. 7.3.19.8.2 Automatic Retry
        9. 7.3.19.9  Supply voltage sensing
        10. 7.3.19.10 nFAULT Output
        11. 7.3.19.11 Fault Condition Summary
      20. 7.3.20 Device Functional Modes
        1. 7.3.20.1 Sleep Mode
        2. 7.3.20.2 Disable Mode
        3. 7.3.20.3 Operating Mode
        4. 7.3.20.4 nSLEEP Reset Pulse
        5. 7.3.20.5 Functional Modes Summary
    4. 7.4 Programming
      1. 7.4.1 Serial Peripheral Interface (SPI) Communication
        1. 7.4.1.1 SPI Format
        2. 7.4.1.2 SPI for Multiple Target Devices in Daisy Chain Configuration
        3. 7.4.1.3 SPI for Multiple Target Devices in Parallel Configuration
    5. 7.5 Register Maps
      1. 7.5.1 Status Registers
        1. 7.5.1.1 FAULT (address = 0x00) [Default = 00h]
        2. 7.5.1.2 DIAG1 (address = 0x01) [Default = 00h]
        3. 7.5.1.3 DIAG2 (address = 0x02) [Default = 00h]
        4. 7.5.1.4 DIAG3 (address = 0x03) [Default = 00h]
      2. 7.5.2 Control Registers
        1. 7.5.2.1  CTRL1 (address = 0x04) [Default = 0Fh]
        2. 7.5.2.2  CTRL2 (address = 0x05) [Default = 06h]
        3. 7.5.2.3  CTRL3 (address = 0x06) [Default = 38h]
        4. 7.5.2.4  CTRL4 (address = 0x07) [Default = 49h]
        5. 7.5.2.5  CTRL5 (address = 0x08) [Default = 03h]
        6. 7.5.2.6  CTRL6 (address = 0x09) [Default = 20h]
        7. 7.5.2.7  CTRL7 (address = 0x0A) [Default = FFh]
        8. 7.5.2.8  CTRL8 (address = 0x0B) [Default = 0Fh]
        9. 7.5.2.9  CTRL9 (address = 0x0C) [Default = 10h]
        10. 7.5.2.10 CTRL10 (address = 0x0D) [Default = 80h]
        11. 7.5.2.11 CTRL11 (address = 0x0E) [Default = FFh]
        12. 7.5.2.12 CTRL12 (address = 0x0F) [Default = 20h]
        13. 7.5.2.13 CTRL13 (address = 0x10) [Default = 10h]
        14. 7.5.2.14 CTRL14 (address = 0x3C) [Default = 58h]
      3. 7.5.3 Indexer Registers
        1. 7.5.3.1 INDEX1 (address = 0x11) [Default = 80h]
        2. 7.5.3.2 INDEX2 (address = 0x12) [Default = 80h]
        3. 7.5.3.3 INDEX3 (address = 0x13) [Default = 80h]
        4. 7.5.3.4 INDEX4 (address = 0x14) [Default = 82h]
        5. 7.5.3.5 INDEX5 (address = 0x15) [Default = B5h]
      4. 7.5.4 Custom Microstepping Registers
        1. 7.5.4.1 CUSTOM_CTRL1 (address = 0x16) [Default = 00h]
        2. 7.5.4.2 CUSTOM_CTRL2 (address = 0x17) [Default = 00h]
        3. 7.5.4.3 CUSTOM_CTRL3 (address = 0x18) [Default = 00h]
        4. 7.5.4.4 CUSTOM_CTRL4 (address = 0x19) [Default = 00h]
        5. 7.5.4.5 CUSTOM_CTRL5 (address = 0x1A) [Default = 00h]
        6. 7.5.4.6 CUSTOM_CTRL6 (address = 0x1B) [Default = 00h]
        7. 7.5.4.7 CUSTOM_CTRL7 (address = 0x1C) [Default = 00h]
        8. 7.5.4.8 CUSTOM_CTRL8 (address = 0x1D) [Default = 00h]
        9. 7.5.4.9 CUSTOM_CTRL9 (address = 0x1E) [Default = 00h]
      5. 7.5.5 Auto torque Registers
        1. 7.5.5.1  ATQ_CTRL1 (address = 0x1F) [Default = 00h]
        2. 7.5.5.2  ATQ_CTRL2 (address = 0x20) [Default = 00h]
        3. 7.5.5.3  ATQ_CTRL3 (address = 0x21) [Default = 00h]
        4. 7.5.5.4  ATQ_CTRL4 (address = 0x22) [Default = 20h]
        5. 7.5.5.5  ATQ_CTRL5 (address = 0x23) [Default = 00h]
        6. 7.5.5.6  ATQ_CTRL6 (address = 0x24) [Default = 00h]
        7. 7.5.5.7  ATQ_CTRL7 (address = 0x25) [Default = 00h]
        8. 7.5.5.8  ATQ_CTRL8 (address = 0x26) [Default = 00h]
        9. 7.5.5.9  ATQ_CTRL9 (address = 0x27) [Default = 00h]
        10. 7.5.5.10 ATQ_CTRL10 (address = 0x28) [Default = 08h]
        11. 7.5.5.11 ATQ_CTRL11 (address = 0x29) [Default = 0Ah]
        12. 7.5.5.12 ATQ_CTRL12 (address = 0x2A) [Default = FFh]
        13. 7.5.5.13 ATQ_CTRL13 (address = 0x2B) [Default = 05h]
        14. 7.5.5.14 ATQ_CTRL14 (address = 0x2C) [Default = 0Fh]
        15. 7.5.5.15 ATQ_CTRL15 (address = 0x2D) [Default = 00h]
        16. 7.5.5.16 ATQ_CTRL16 (address = 0x2E) [Default = FFh]
        17. 7.5.5.17 ATQ_CTRL17 (address = 0x2F) [Default = 00h]
        18. 7.5.5.18 ATQ_CTRL18 (address = 0x30) [Default = 00h]
      6. 7.5.6 Silent Step Registers
        1. 7.5.6.1 SS_CTRL1 (address = 0x31) [Default = 00h]
        2. 7.5.6.2 SS_CTRL2 (address = 0x32) [Default = 00h]
        3. 7.5.6.3 SS_CTRL3 (address = 0x33) [Default = 00h]
        4. 7.5.6.4 SS_CTRL4 (address = 0x34) [Default = 00h]
        5. 7.5.6.5 SS_CTRL5 (address = 0x35) [Default = FFh]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Stepper Motor Speed
      3. 8.2.3 Application Performance Plots
      4. 8.2.4 Thermal Application
        1. 8.2.4.1 Power Dissipation
        2. 8.2.4.2 Conduction Loss
        3. 8.2.4.3 Switching Loss
        4. 8.2.4.4 Power Dissipation Due to Quiescent Current
        5. 8.2.4.5 Total Power Dissipation
        6. 8.2.4.6 Device Junction Temperature Estimation
  10. 9 Thermal Considerations
    1. 9.1 Thermal Pad
    2. 9.2 PCB Material Recommendation
  11. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance
    2. 10.2 Power Supplies
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

5 Pin Configuration and Functions

GUID-20220521-SS0I-ZWN4-P5Z8-CHHFN3NGGCJF-low.svgFigure 5-1 DDW Package (44-Pin HTSSOP), SPI or H/W interface, Top View
GUID-20220801-SS0I-M2KB-HKJX-D768DBMRLMWD-low.svgFigure 5-2 PWP Package (28-Pin HTSSOP) with SPI interface, Top View
GUID-20220801-SS0I-DM1H-PS6D-CLJX6BH4CNW6-low.svgFigure 5-3 PWP Package (28-Pin HTSSOP) with H/W interface, Top View
PINTYPEDESCRIPTION
NAME

DDW

PWP

SPI Interface

H/W Interface

VCC

25

19

-

Power

Supply voltage for internal logic blocks. When separate logic supply voltage is not available, tie the VCC pin to the DVDD pin. When configured with SPI interface, the VCC pin also acts as the supply pin for SDO output. See Section 7.3.16 for details.

RSVD/TOFF

35

-

19

Input

This pin is not used with SPI interface. With H/W interface, this pin programs the OFF time for PWM current regulation.

VCP1

1

Power

Charge pump output. Connect a X7R, 1-μF, 16-V ceramic capacitor from VCP to VM.

VM

2, 11, 12, 21

2, 13

Power

Power supply. Connect to motor supply voltage and bypass to PGNDA and PGNDB with two 0.01-μF ceramic capacitors plus a bulk capacitor rated for VM.

PGNDA

3, 10

3

Power

Power ground. Connect to system ground.

PGNDB

13, 20

12

Power

Power ground. Connect to system ground.
AOUT1

4, 5, 6

4, 5

OutputWinding A output. Connect to motor winding.
AOUT2

7, 8, 9

6, 7

Output

Winding A output. Connect to motor winding.

BOUT2

14, 15, 16

8, 9

Output

Winding B output. Connect to motor winding.

BOUT1

17, 18, 19

10, 11

Output

Winding B output. Connect to motor winding.
GND

22, 23

14

PowerDevice ground. Connect to system ground.
DVDD

24

15

PowerInternal LDO output. Connect a X7R, 1-μF, 6.3-V or 10-V rated ceramic capacitor to GND.

nFAULT

26

16

Open Drain

Fault indication output. Pulled logic low with fault condition. Open-drain nFAULT requires an external pullup resistor.
nHOME

27

-

Open Drain

Pulled logic low when the internal indexer is at home position (45°) of step table. The nHOME pin outputs one low pulse per 360º electrical rotation (four fullsteps). Only available with DDW package. See Section 7.3.5.1 for details.

MODE

28

-

InputFor the DDW package, MODE pin programs the device with either SPI or hardware (H/W) pin interface. See Section 7.3.1 for details.

RSVD

29, 30, 31, 32

-

-Reserved. Leave unconnected.

VREF

33

17

InputVoltage reference input for setting full-scale current. DVDD can be used to generate VREF through a resistor divider. When configured with SPI interface, the VREF pin can be left unconnected if VREF_INT_EN = 1b.

nSCS/M0

34

18

InputWith SPI interface, this pin acts as serial chip select. An active low on this pin enables the serial interface communications. With H/W interface, this pin programs the microstepping mode.

SDO/DECAY1

36

20

Push-Pull/Input

With SPI interface, this pin acts as serial data output. Data is shifted out on the rising edge of the SCLK pin. With H/W interface, this pin programs the decay-mode.

SDI/DECAY0

37

21

Input

With SPI interface, this pin acts as serial data input. Data is captured on the falling edge of the SCLK pin. With H/W interface, this pin programs the decay-mode.

SCLK/M1

38

22

Input

With SPI interface, this pin acts as serial clock input. Serial data is shifted out and captured on the corresponding rising and falling edge on this pin. With H/W interface, this pin programs the microstepping mode.

STEP

39

23

InputStep input. An active edge causes the indexer to advance one step. With SPI interface, STEP active edge can be either rising edge or both rising and falling edge. With H/W interface, STEP active edge is always the rising edge.

DIR

40

24

InputDirection input. Logic level sets the direction of stepping.

ENABLE

41

25

InputLogic low to disable device outputs; logic high to enable. When the device operates with H/W interface, the ENABLE pin also determines the OCP, OL and OTSD fault recovery methods.

nSLEEP

42

26

InputSleep mode input. Logic high to enable device; logic low to enter low-power sleep mode. A narrow nSLEEP reset pulse clears latched faults.

CPL

43

27

Power

Charge pump switching node. Connect a X7R, 0.1-μF, VM-rated ceramic capacitor from CPH to CPL.

CPH

44

28

Power

PAD---Thermal pad. Connect to system ground.