SNLS141 Data sheet

SNLS141E August 2002 – March 2024 DS90LT012A , DS90LV012A

PRODUCTION DATA

Package Options

Mechanical Data (Package|Pins)

DBV|5
- MPDS018T

Thermal pad, mechanical data (Package|Pins)

Orderable Information

4.3 Electrical Characteristics

Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. ⁽¹⁾⁽²⁾

PARAMETER		TEST CONDITIONS		PIN	MIN	TYP	MAX	UNIT
V_TH	Differential Input High Threshold	Valid across the specified common mode voltage (V_CM) range.⁽³⁾		IN+, IN−		−30	0	mV
V_TL	Differential Input Low Threshold				−100	−30		mV
V_CM	Common-Mode Voltage	V_DD = 2.7V, V_ID = 100mV			0.05		2.35	V
V_CM	Common-Mode Voltage	V_DD = 3.0V to 3.6V, V_ID = 100mV			0.05		V_DD - 0.3V	V
I_IN	Input Current (DS90LV012A)	V_IN = +2.8V	V_DD = 3.6V or 0V		−10	±1	+10	μA
		V_IN = 0V	V_DD = 3.6V or 0V		−10	±1	+10	μA
		V_IN = +3.6V	V_DD = 0V		−20		+20	μA
ΔI_IN	Change in Magnitude of I_IN	V_IN = +2.8V	V_DD = 3.6V or 0V			4		μA
		V_IN = 0V	V_DD = 3.6V or 0V			4		μA
		V_IN = +3.6V	V_DD = 0V			4		μA
I_IND	Differential Input Current	V_IN+ = +0.4V, V_IN− = +0V			3	3.9	4.4	mA
I_IND	(DS90LT012A)	V_IN+ = +2.4V, V_IN− = +2.0V			3	3.9	4.4	mA
R_T	Integrated Termination Resistor (DS90LT012A)					102		Ω
C_IN	Input Capacitance	IN+ = IN− = GND				3		pF
V_OH	Output High Voltage	I_OH = −0.4 mA, V_ID = +200 mV		TTL OUT	2.4	3.1		V
		I_OH = −0.4 mA, Inputs terminated			2.4	3.1		V
		I_OH = −0.4 mA, Inputs shorted			2.4	3.1		V
V_OL	Output Low Voltage	I_OL = 2 mA, V_ID = −200 mV				0.3	0.5	V
I_OS	Output Short Circuit Current	V_OUT = 0V ⁽⁴⁾			−15	−50	−100	mA
V_CL	Input Clamp Voltage	I_CL = −18 mA			−1.5	−0.7		V
I_DD	No Load Supply Current	Inputs Open		V_DD		5.4	9	mA

(1) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise specified (such as V_ID).

(2) All typicals are given for: V_DD = +3.3V and T_A = +25°C..

(3) V_DD is always higher than IN+ and IN− voltage. IN+ and IN− are allowed to have voltage range −0.05V to +2.35V when V_DD = 2.7V and |V_ID| / 2 to V_DD − 0.3V when V_DD = 3.0V to 3.6V. V_ID is not allowed to be greater than 100 mV when V_CM = 0.05V to 2.35V when V_DD = 2.7V or when V_CM = |V_ID| / 2 to V_DD − 0.3V when V_DD = 3.0V to 3.6V.

(4) Output short circuit current (I_OS) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not exceed maximum junction temperature specification.