SLCS005 Data sheet

SLCS005AF october 1979 – august 2023 LM193 , LM2903 , LM2903B , LM2903V , LM293 , LM293A , LM393 , LM393A , LM393B

PRODUCTION DATA

Package Options

Mechanical Data (Package|Pins)

D|8
- MSOI002K
PW|8
- MPDS568
PS|8
- MSOP001A
DGK|8
- MPDS028E
P|8
- MPDI001B

Thermal pad, mechanical data (Package|Pins)

PS|8
- QFND376

Orderable Information

6.11 Electrical Characteristics for LM293A and LM393A

at specified free-air temperature, V_CC = 5 V (unless otherwise noted)

PARAMETER		TEST CONDITIONS		T_A⁽¹⁾	LM293A LM393A			UNIT
PARAMETER		TEST CONDITIONS		T_A⁽¹⁾	MIN	TYP	MAX	UNIT
V_IO	Input offset voltage	V_CC = 5 V to 30 V, V_O = 1.4 V V_IC = V_ICR(min)		25°C		1	2	mV
V_IO	Input offset voltage	V_CC = 5 V to 30 V, V_O = 1.4 V V_IC = V_ICR(min)		Full range			4	mV
I_IO	Input offset current	V_O = 1.4 V		25°C		5	50	nA
I_IO	Input offset current	V_O = 1.4 V		Full range			150	nA
I_IB	Input bias current	V_O = 1.4 V		25°C		–25	–250	nA
I_IB	Input bias current	V_O = 1.4 V		Full range			–400	nA
V_ICR	Common-mode input-voltage range⁽²⁾			25°C	0 to V_CC – 1.5			V
V_ICR	Common-mode input-voltage range⁽²⁾			Full range	0 to V_CC – 2			V
A_VD	Large-signal differential-voltage amplification	V_CC = 15 V, V_O = 1.4 V to 11.4 V, R_L ≥ 15 kΩ to V_CC		25°C	50	200		V/mV
I_OH	High-level output current	V_OH = 5 V,	V_ID = 1 V	25°C		0.1	50	nA
I_OH	High-level output current	V_OH = 30 V,	V_ID = 1 V	Full range			1	µA
V_OL	Low-level output voltage	I_OL = 4 mA,	V_ID = –1 V	25°C		110	400	mV
V_OL	Low-level output voltage	I_OL = 4 mA,	V_ID = –1 V	Full range			700	mV
I_OL	Low-level output current	V_OL = 1.5 V,	V_ID = –1 V,	25°C	6			mA
I_CC	Supply current	R_L = ∞	V_CC = 5 V	25°C		0.60	1	mA
I_CC	Supply current	R_L = ∞	V_CC = 30 V	Full range		0.72	2.5	mA

(1) Full range (minimum or maximum) for LM293A is –25°C to 85°C, and for LM393A is 0°C to 70°C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified.

(2) The voltage at either input should not be allowed to go negative by more than 0.3 V otherwise output may be incorrect and excessive input current can flow. The upper end of the common-mode voltage range is limited by V_CC – 2V. However only one input needs to be in the valid common mode range, the other input can go up the maximum V_CC level and the comparator provides a proper output state. Either or both inputs can go to maximum V_CC level without damage.