SNVSBU7 September   2020 LM34966-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Line Undervoltage Lockout (UVLO/SYNC/EN Pin)
      2. 8.3.2  High Voltage VCC Regulator (BIAS, VCC Pin)
      3. 8.3.3  Soft Start (SS Pin)
      4. 8.3.4  Switching Frequency (RT Pin)
      5. 8.3.5  Clock Synchronization (UVLO/SYNC/EN Pin)
      6. 8.3.6  Current Sense and Slope Compensation (CS Pin)
      7. 8.3.7  Current Limit and Minimum On-time (CS Pin)
      8. 8.3.8  Feedback and Error Amplifier (FB, COMP Pin)
      9. 8.3.9  Power-Good Indicator (PGOOD Pin)
      10. 8.3.10 Hiccup Mode Overload Protection
      11. 8.3.11 Maximum Duty Cycle Limit and Minimum Input Supply Voltage
      12. 8.3.12 MOSFET Driver (GATE Pin)
      13. 8.3.13 Overvoltage Protection (OVP)
      14. 8.3.14 Thermal Shutdown (TSD)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Run Mode
  9. 9 Application and Implementation
    1. 9.1 Power-On Hours (POH)
    2. 9.2 Application Information
    3. 9.3 Typical Application
      1. 9.3.1 Design Requirements
      2. 9.3.2 Detailed Design Procedure
        1. 9.3.2.1 Custom Design With WEBENCH® Tools
        2. 9.3.2.2 Recommended Components
        3. 9.3.2.3 Inductor Selection (LM)
        4. 9.3.2.4 Output Capacitor (COUT)
        5. 9.3.2.5 Input Capacitor
        6. 9.3.2.6 MOSFET Selection
        7. 9.3.2.7 Diode Selection
        8. 9.3.2.8 Efficiency Estimation
      3. 9.3.3 Application Curve
    4. 9.4 System Examples
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Examples
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
      2. 12.1.2 Development Support
        1. 12.1.2.1 Custom Design With WEBENCH® Tools
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Pin Functions

PINTYPE(1)DESCRIPTION
NO.NAME
1BIASPSupply voltage input to the VCC regulator. Connect a bypass capacitor from this pin to PGND.
2NC-No electrical contact
3VCCPOutput of the internal VCC regulator and supply voltage input of the MOSFET driver. Connect a ceramic bypass capacitor from this pin to PGND.
4GATEON-channel MOSFET gate drive output. Connect directly to the gate of the N-channel MOSFET through a short, low inductance path.
5PGNDGPower ground pin. Connect directly to the ground connection of the sense resistor through a low inductance wide and short path.
6AGNDGAnalog ground pin. Connect directly to the analog ground plane through a wide and short path.
7CSICurrent sense input pin. Connect to the positive side of the current sense resistor through a short path.
8COMPOOutput of the internal transconductance error amplifier. Connect the loop compensation components between this pin and ground plane.
9VDDIInput of the internal logic. Connect directly to VCC.
10FBIInverting input of the error amplifier. Connect a voltage divider from the output to this pin to set output voltage in boost/SEPIC/non-isolated flyback topologies. Connect the low-side feedback resistor to AGND.
11SSISoft-start time programming pin. An external capacitor and an internal current source set the ramp rate of the internal error amplifier reference during soft start. Connect the ground connection of the capacitor to AGND.
12RTISwitching frequency setting pin. The switching frequency is programmed by a single resistor between RT and AGND.
13PGOODOPower-good indicator. An open-drain output which goes low if FB is below the undervoltage threshold. Connect a pullup resistor to the system voltage rail. If not used, leave the pin floating.
14EN/UVLO/SYNCIUndervoltage lockout programming pin. The converter start-up and shutdown levels can be programmed by connecting this pin to the supply voltage through a resistor divider. The internal clock can be synchronized to an external clock by applying a negative pulse signal into the EN/UVLO/SYNC pin. This pin must not be left floating. Connect to BIAS pin if not used. Connect the low-side UVLO resistor to AGND.
—EP—Exposed pad of the package. The exposed pad must be connected to AGND and the large ground copper plane to decrease thermal resistance.
(1) G = Ground, I = Input, O = Output, P = Power