SNOS760D May   1999  – February 2024 LM7171

PRODUCTION DATA  

  1.   1
  2. 1Features
  3. 2Applications
  4. 3Description
  5. 4Pin Configuration and Functions
  6. 5Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics: ±15V
    6. 5.6 Electrical Characteristics: ±5V
    7. 5.7 Typical Characteristics: LM7171A
    8. 5.8 Typical Characteristics: LM7171B
  7. 6Application and Implementation
    1. 6.1 Application Information
      1. 6.1.1 Circuit Operation
      2. 6.1.2 Slew Rate Characteristic
        1. 6.1.2.1 Slew-Rate Limitation
      3. 6.1.3 Compensation for Input Capacitance
    2. 6.2 Typical Applications
    3. 6.3 Power Supply Recommendations
      1. 6.3.1 Power-Supply Bypassing
      2. 6.3.2 Termination
      3. 6.3.3 Driving Capacitive Loads
      4. 6.3.4 Power Dissipation
    4. 6.4 Layout
      1. 6.4.1 Layout Guidelines
        1. 6.4.1.1 Printed Circuit Board and High-Speed Op Amps
        2. 6.4.1.2 Using Probes
        3. 6.4.1.3 Component Selection and Feedback Resistor
  8. 7Device and Documentation Support
    1. 7.1 Receiving Notification of Documentation Updates
    2. 7.2 Support Resources
    3. 7.3 Trademarks
    4. 7.4 Electrostatic Discharge Caution
    5. 7.5 Glossary
  9. 8Revision History
  10. 9Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • D|8
  • P|8
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8 Revision History

Changes from Revision C (September 2014) to Revision D (February 2024)

  • Updated the numbering format for tables, figures, and cross-references throughout the documentGo
  • Updated Package Information Go
  • Deleted footnote from Recommended Operating Conditions.Go
  • Changed DC and AC specifications tables to Electrical Characteristics: ±15V Go
  • Changed LM7171A unity-gain bandwidth from 200MHz to 160MHzGo
  • Changed LM7171A settling time from 42ns to 16nsGo
  • Changed LM7171 A Input-referred voltage noise from 14nV/√Hz to 8.5nV/√HzGo
  • Changed LM7171 A Input-referred current noise from 1.5pA/√Hz to 1pA/√HzGo
  • Changed DC and AC specifications tables to Electrical Characteristics: ±5V Go
  • Changed LM7171A slew rate from 950V/µs to 1200V/µsGo
  • Changed LM7171A phase margin from 57° to 68°Go
  • Changed LM7171A settling time from 56ns to 15nsGo
  • Changed LM7171A propagation delay from 6ns to 2.5nsGo
  • Changed LM7171A input-referred voltage noise from 14nV/√Hz to 8.5nV/√HzGo
  • Changed LM7171A input-referred current noise from 1.8pA/√Hz to 1pA/√HzGo
  • Added new Typical Characteristics section for LM7171AGo
  • Deleted second paragraph in Slew-Rate Limitation Go

Changes from Revision B (March 2013) to Revision C (September 2014)

  • Changed data sheet flow and layout to conform with new TI standards. Added the following sections: Device Information Table, Application and Implementation; Layout; Device and Documentation Support; Mechanical, Packaging, and Ordering Information Go

Changes from Revision A (March 2013) to Revision B (March 2013)

  • Changed layout of National Data Sheet to TI formatGo