SLLSFN8 September   2023 THVD1330

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Data Rate and Bus Length
        2. 9.2.1.2 Stub Length
        3. 9.2.1.3 Bus Loading
        4. 9.2.1.4 Receiver Failsafe
        5. 9.2.1.5 Transient Protection
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Third-Party Products Disclaimer
    2. 10.2 Device Support
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.5 Electrical Characteristics

over operating free-air temperature range, Typical values are at 25 ℃ and 3.3 V supply (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver
|VOD| Driver differential output voltage magnitude RL = 60 Ω, -7 V ≤ Vtest ≤ 12 V, See Figure 6-1 1.5 V
RL = 54 Ω, See Figure 6-2 1.5 V
No load 2 3.6 V
Δ|VOD| Change in differential output voltage RL = 54 Ω, See Figure 6-2 –50 50 mV
VOC Common-mode output voltage RL = 54 Ω, See Figure 6-2 1.4 2.5 V
VOC(SS) Change in steady-state common-mode output voltage RL = 54 Ω , See Figure 6-2 –50 50 mV
VOC(pp) Peak-to-peak common-mode output voltage RL = 54 Ω  , CL=50pF, PRR=500KHz, See Figure 6-2 400 mV
IOS Short-circuit output current DE = VCC, -7 V <VO < 12 V, Voltage applied on one bus line with other bus line floating –250 250 mA
COD Differential output capacitance VI=0.4 sin (4E6πt) + 0.5 V, DE=0 16 pF
Receiver
II Bus input current VCC = 3.6 V VI = 12 V 200 500 µA
VI = -7 V –400 –200
VCC = 0 V VI = 12 V 250 500
VI = -7 V –400 –150
VTH+ Positive-going input-threshold voltage(1) Over common-mode range of (+12V,-7V) –75 –20 mV
VTH- Negative-going input-threshold voltage(1) –200 –125 mV
VHYS Input hysteresis 50 mV
VOH Output high voltage IOH = -8 mA 2.4 V
VOL Output low voltage IOL = 8 mA 0.4 V
IOZ Output high-impedance current VO = 0 V or VCC, RE = VCC –1 1 µA
CID Differential input capacitance VI=0.4 sin (4E6πt) + 0.5 V, DE=0 15 pF
Logic
IIN Input current DE VIN= 5V 0 100 µA
Input current DE VIN= 0V 0 100 µA
Input current D VIN= 5V –100 0 µA
Input current D VIN= 0V –100 0 µA
Input current ( RE) VIN = 2V –30 0 µA
VIN = 0.8V –30 0 µA
Thermal Protection
TSHDN Thermal shutdown threshold Temperature rising 150 170 °C
THYS Thermal shutdown hysteresis 10 °C
Supply
ICC Supply current (quiescent) Driver and receiver enabled RE = 0 V, DE = VCC, No load 2 mA
Driver enabled, receiver disabled RE = VCC, DE = VCC, No load 1.5 mA
Driver disabled, receiver enabled RE = 0 V, DE = 0 V, No load 1.5 mA
Driver and receiver disabled RE = VCC, DE = 0 V, D = VCC, No load 5 µA
(1) Under any specific conditions, VTH+ is assured to be at least VHYS higher than VTH–.