SLVS736C February   2008  – October 2023 TPS2550 , TPS2551

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Parameter Measurement Information
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Overcurrent
      2. 9.3.2 Reverse-Voltage Protection
      3. 9.3.3 FAULT Response
      4. 9.3.4 Undervoltage Lockout (UVLO)
      5. 9.3.5 ENABLE ( EN or EN)
      6. 9.3.6 Thermal Sense
      7. 9.3.7 Device Functional Modes
    4. 9.4 Programming
      1. 9.4.1 Programming the Current-Limit Threshold
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Two-Level Current-Limit Circuit
      2. 10.2.2 Design Requirements
      3. 10.2.3 Detail Design Procedures
        1. 10.2.3.1 Designing Above a Minimum Current Limit
        2. 10.2.3.2 Designing Below a Maximum Current Limit
        3. 10.2.3.3 Input and Output Capacitance
      4. 10.2.4 Auto-Retry Functionality
      5. 10.2.5 Latch-Off Functionality
      6. 10.2.6 Typical Application as USB Power Switch
        1. 10.2.6.1 Design Requirements
          1. 10.2.6.1.1 USB Power-Distribution Requirements
        2. 10.2.6.2 Detail Design Procedures
          1. 10.2.6.2.1 Universal Serial Bus (USB) Power-Distribution Requirements
    3. 10.3 Power Supply Recommendations
      1. 10.3.1 Self-Powered and Bus-Powered Hubs
      2. 10.3.2 Low-Power Bus-Powered and High-Power Bus-Powered Functions
      3. 10.3.3 Power Dissipation and Junction Temperature
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Support Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.1 Absolute Maximum Ratings

over operating free-air temperature range unless otherwise noted(1)(2)
VALUEUNIT
Voltage range on IN, OUT, EN or EN, ILIM, FAULT–0.3 to 7V
Voltage range from IN to OUT–7 to 7V
IOUTContinuous output currentInternally limited
Continuous total power dissipationSee "Thermal Information Table"
FAULT sink current25mA
ILIM source current1mA
TJMaximum junction temperature–40 to 150°C
TSgtStorage temperature–65 to 150°C
Lead temperature 1,6 mm (1/16-inch) from case for 10 seconds300°C
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.
(2) Voltages are referenced to GND unless otherwise noted.