SLVSH67 September   2024 TPS26750

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
      1. 5.1.1 TPS26750 - Absolute Maximum Ratings
      2. 5.1.2 TPS26750 - Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
      1. 5.3.1 TPS26750 - Recommended Operating Conditions
    4. 5.4  Recommended Capacitance
    5. 5.5  Thermal Information
      1. 5.5.1 TPS26750 - Thermal Information
    6. 5.6  Power Supply Characteristics
    7. 5.7  Power Consumption
    8. 5.8  PP_5V Power Switch Characteristics
    9. 5.9  POWER_PATH_EN Characteristics - TPS26750
    10. 5.10 Power Path Supervisory
    11. 5.11 CC Cable Detection Parameters
    12. 5.12 CC VCONN Parameters
    13. 5.13 CC PHY Parameters
    14. 5.14 Thermal Shutdown Characteristics
    15. 5.15 ADC Characteristics
    16. 5.16 Input/Output (I/O) Characteristics
    17. 5.17 BC1.2 Characteristics
    18. 5.18 I2C Requirements and Characteristics
    19. 5.19 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  USB-PD Physical Layer
        1. 7.3.1.1 USB-PD Encoding and Signaling
        2. 7.3.1.2 USB-PD Bi-Phase Marked Coding
        3. 7.3.1.3 USB-PD Transmit (TX) and Receive (Rx) Masks
        4. 7.3.1.4 USB-PD BMC Transmitter
        5. 7.3.1.5 USB-PD BMC Receiver
        6. 7.3.1.6 Squelch Receiver
      2. 7.3.2  Power Management
        1. 7.3.2.1 Power-On And Supervisory Functions
        2. 7.3.2.2 VBUS LDO
      3. 7.3.3  Power Paths
        1. 7.3.3.1 Internal Sourcing Power Paths
          1. 7.3.3.1.1 PP_5V Current Clamping
          2. 7.3.3.1.2 PP_5V Local Overtemperature Shut Down (OTSD)
          3. 7.3.3.1.3 PP_5V OVP
          4. 7.3.3.1.4 PP_5V UVLO
          5. 7.3.3.1.5 PP_5Vx Reverse Current Protection
          6. 7.3.3.1.6 PP_CABLE Current Clamp
          7. 7.3.3.1.7 PP_CABLE Local Overtemperature Shut Down (OTSD)
          8. 7.3.3.1.8 PP_CABLE UVLO
      4. 7.3.4  Cable Plug and Orientation Detection
        1. 7.3.4.1 Configured as a Source
        2. 7.3.4.2 Configured as a Sink
        3. 7.3.4.3 Configured as a DRP
        4. 7.3.4.4 Dead Battery Advertisement
      5. 7.3.5  Overvoltage Protection (CC1, CC2)
      6. 7.3.6  Default Behavior Configuration (ADCIN1, ADCIN2)
      7. 7.3.7  ADC
      8. 7.3.8  BC 1.2 (USB_P, USB_N)
      9. 7.3.9  Digital Interfaces
        1. 7.3.9.1 General GPIO
        2. 7.3.9.2 I2C Interface
      10. 7.3.10 Digital Core
      11. 7.3.11 I2C Interface
        1. 7.3.11.1 I2C Interface Description
          1. 7.3.11.1.1 I2C Clock Stretching
          2. 7.3.11.1.2 I2C Address Setting
          3. 7.3.11.1.3 Unique Address Interface
    4. 7.4 Device Functional Modes
      1. 7.4.1 Pin Strapping to Configure Default Behavior
      2. 7.4.2 Power States
    5. 7.5 Thermal Shutdown
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 Programmable Power Supply (PPS) - Design Requirements
        2. 8.2.1.2 Liquid Detection Design Requirements
        3. 8.2.1.3 BC1.2 Application Design Requirements
        4. 8.2.1.4 USB Data Support Design Requirements
        5. 8.2.1.5 EPR Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Programmable Power Supply (PPS)
        2. 8.2.2.2 Liquid Detection
        3. 8.2.2.3 BC1.2 Application
        4. 8.2.2.4 USB Data Support
        5. 8.2.2.5 Power Delivery EPR Support
      3. 8.2.3 Application Curves
        1. 8.2.3.1 Programmable Power Supply (PPS) Application Curves
        2. 8.2.3.2 Liquid Detection Application Curves
        3. 8.2.3.3 BC1.2 Application Curves
        4. 8.2.3.4 USB Data Support Application Curves
        5. 8.2.3.5 EPR Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 3.3V Power
        1. 8.3.1.1 VIN_3V3 Input Switch
      2. 8.3.2 1.5V Power
      3. 8.3.3 Recommended Supply Load Capacitance
    4. 8.4 Layout
      1. 8.4.1 TPS26750 - Layout
        1. 8.4.1.1 Layout Guidelines
          1. 8.4.1.1.1 Recommended Via Size
          2. 8.4.1.1.2 Minimum Trace Widths
        2. 8.4.1.2 Layout Example
          1. 8.4.1.2.1 TPS26750 Schematic Layout Example
          2. 8.4.1.2.2 TPS26750 Layout Example - PCB Plots
            1. 8.4.1.2.2.1 TPS26750 Component Placement
            2. 8.4.1.2.2.2 TPS26750 PP5V
            3. 8.4.1.2.2.3 TPS26750 PP_EXT
            4. 8.4.1.2.2.4 TPS26750 VBUS
            5. 8.4.1.2.2.5 TPS26750 I/O
            6. 8.4.1.2.2.6 TPS26750 PPEXT Gate Driver
            7. 8.4.1.2.2.7 TPS26750 GND
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • RSM|32
Thermal pad, mechanical data (Package|Pins)
Orderable Information
8.4.1.2.2.4 TPS26750 VBUS

VBUS (pins 26 and 27)

Place the VBUS decoupling capacitor (C37) as close as possible to the VBUS pin of the excernal NMOS transistor (Q8), the capacitor does not need to be on the same layer as the device. The VBUS power plane need to be sized to support up to 3A o fcurrent if the 5V power path is utalized. If this 5V power path is not utilized, then the power path can be sized to support 100mA of current. When connecting the VBUS pins (pins 26 and 27) plane to a different layer, use a minimum of 3 vias per layer change.

At the Type-C port/connector, it is recommended to use minimum of 6 vias from the connector VBUS pins for layer changes. Place the 10nF caps (C2, C3, C4, and C5) as close as possible to the connector VBUS pins as shown in figure 10-22.

When implemented with the TPD4S480, the TPS26750 does not require an external TVS protection device, but the power switch used in the system may require the addition of a TVS protection diode. Please refer to the datasheet of the switch selected to ensure that any protection requirements are met.

The VBUS line of the type C connector needs to be routed to the external power path in a manner that supports it's current and voltage needs. Please refer to the datasheet of the switch selected to ensure that any routing and current requirements are met.