SLVSGL3 April   2022 TPSM63603E

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  System Characteristics
    7. 7.7  Typical Characteristics
    8. 7.8  Typical Characteristics — VIN = 12 V
    9. 7.9  Typical Characteristics — VIN = 24 V
    10. 7.10 Typical Characteristics — VIN = 36 V
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Input Voltage Range
      2. 8.3.2  Adjustable Output Voltage (FB)
      3. 8.3.3  Input Capacitors
      4. 8.3.4  Output Capacitors
      5. 8.3.5  Switching Frequency (RT)
      6. 8.3.6  Output ON and OFF Enable (EN/SYNC) and VIN UVLO
      7. 8.3.7  Frequency Synchronization (EN/SYNC)
      8. 8.3.8  Spread Spectrum
      9. 8.3.9  Power-Good Monitor (PG)
      10. 8.3.10 Adjustable Switch-Node Slew Rate (RBOOT and CBOOT)
      11. 8.3.11 Internal LDO, VCC Output, and VLDOIN Input
      12. 8.3.12 Overcurrent Protection (OCP)
      13. 8.3.13 Thermal Shutdown
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
  9. 9 Applications and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Design 1 — 3-A Synchronous Buck Regulator for Industrial Applications
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Custom Design With WEBENCH® Tools
          2. 9.2.1.2.2 Output Voltage Setpoint
          3. 9.2.1.2.3 Switching Frequency Selection
          4. 9.2.1.2.4 Input Capacitor Selection
          5. 9.2.1.2.5 Output Capacitor Selection
          6. 9.2.1.2.6 Other Connections
        3. 9.2.1.3 Application Curves
        4. 9.2.1.4 Design 2 — Inverting Buck-Boost Regulator with a –5-V Output
          1. 9.2.1.4.1 Design Requirements
          2. 9.2.1.4.2 Detailed Design Procedure
            1. 9.2.1.4.2.1 Output Voltage Setpoint
            2. 9.2.1.4.2.2 IBB Maximum Output Current
            3. 9.2.1.4.2.3 Switching Frequency Selection
            4. 9.2.1.4.2.4 Input Capacitor Selection
            5. 9.2.1.4.2.5 Output Capacitor Selection
            6. 9.2.1.4.2.6 Other Connections
            7. 9.2.1.4.2.7 EMI
              1. 9.2.1.4.2.7.1 EMI Plots
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
      1. 11.2.1 Package Specifications
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
      2. 12.1.2 Development Support
        1. 12.1.2.1 Custom Design With WEBENCH® Tools
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 Support Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.6 System Characteristics

The following specifications apply only to the typical applications circuit, with nominal component values. Specifications in the typical (TYP) column apply to TJ = 25°C only. These specifications are not ensured by production testing.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY
IIN Input supply current when in regulation VIN = 24 V, VOUT = 3.3 V, VEN/SYNC = VIN, VVLDOIN = VOUT, fSW = 800 kHz, IOUT = 0 A 10 mA
OUTPUT VOLTAGE
VFB Load regulation VOUT = 3.3 V, VIN = 24 V, IOUT = 0.1 A to full load 1 mV
VFB Line regulation VOUT = 3.3 V, VIN = 4 V to 36 V, IOUT = 3 A 6 mV
VOUT Load transient VOUT = 3.3 V, VIN = 24 V, IOUT = 1 A to 2.5 A at 2 A/μs,  COUT(derated) = 49 μF 50 mV
EFFICIENCY
η Efficiency VOUT = 3.3 V, VIN = 12 V, IOUT = 2.5 A, VLDOIN = VOUT, fSW = 800 kHz 89.5%
VOUT = 3.3 V, VIN = 24 V, IOUT = 2.5 A, VLDOIN = VOUT, fSW = 800 kHz 87.5%
VOUT = 5 V, VIN = 24 V, IOUT = 2.5 A, VLDOIN = VOUT, fSW = 1 MHz 91%
VOUT = 5 V, VIN = 36 V, IOUT = 2.5 A, VLDOIN = VOUT, fSW = 1 MHz 88.1%
VOUT = 12 V, VIN = 24 V, IOUT = 1.5 A, VLDOIN = VOUT, fSW = 2 MHz 94.1%