SLLSE09J November   2009  – July 2021 TUSB1210

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Analog I/O Electrical Characteristics
    6. 6.6  Digital I/O Electrical Characteristics
    7. 6.7  Digital IO Pins (Non-ULPI)
    8. 6.8  PHY Electrical Characteristics
    9. 6.9  Pullup/Pulldown Resistors
    10. 6.10 OTG Electrical Characteristics
    11. 6.11 OTG ID Electrical
    12. 6.12 Power Characteristics
    13. 6.13 Switching Characteristics
    14. 6.14 Timing Requirements
      1. 6.14.1 Timing Parameter Definitions
      2. 6.14.2 Interface Target Frequencies
    15. 6.15 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Processor Subsystem
        1. 7.3.1.1 Clock Specifications
          1. 7.3.1.1.1 USB PLL Reference Clock
          2. 7.3.1.1.2 ULPI Input Clock Configuration
          3. 7.3.1.1.3 ULPI Output Clock Configuration
          4. 7.3.1.1.4 Clock 32 kHz
          5. 7.3.1.1.5 Reset
        2. 7.3.1.2 USB Transceiver
          1. 7.3.1.2.1 PHY Electrical Characteristics
            1. 7.3.1.2.1.1 LS/FS Single-Ended Receivers
            2. 7.3.1.2.1.2 LS/FS Differential Receiver
            3. 7.3.1.2.1.3 LS/FS Transmitter
            4. 7.3.1.2.1.4 HS Differential Receiver
            5. 7.3.1.2.1.5 HS Differential Transmitter
            6. 7.3.1.2.1.6 UART Transceiver
          2. 7.3.1.2.2 OTG Characteristics
    4. 7.4 Device Functional Modes
      1. 7.4.1 TUSB1210 Modes vs ULPI Pin Status
    5. 7.5 Register Map
      1. 7.5.1  VENDOR_ID_LO
      2. 7.5.2  VENDOR_ID_HI
      3. 7.5.3  PRODUCT_ID_LO
      4. 7.5.4  PRODUCT_ID_HI
      5. 7.5.5  FUNC_CTRL
      6. 7.5.6  FUNC_CTRL_SET
      7. 7.5.7  FUNC_CTRL_CLR
      8. 7.5.8  IFC_CTRL
      9. 7.5.9  IFC_CTRL_SET
      10. 7.5.10 IFC_CTRL_CLR
      11. 7.5.11 OTG_CTRL
      12. 7.5.12 OTG_CTRL_SET
      13. 7.5.13 OTG_CTRL_CLR
      14. 7.5.14 USB_INT_EN_RISE
      15. 7.5.15 USB_INT_EN_RISE_SET
      16. 7.5.16 USB_INT_EN_RISE_CLR
      17. 7.5.17 USB_INT_EN_FALL
      18. 7.5.18 USB_INT_EN_FALL_SET
      19. 7.5.19 USB_INT_EN_FALL_CLR
      20. 7.5.20 USB_INT_STS
      21. 7.5.21 USB_INT_LATCH
      22. 7.5.22 DEBUG
      23. 7.5.23 SCRATCH_REG
      24. 7.5.24 SCRATCH_REG_SET
      25. 7.5.25 SCRATCH_REG_CLR
      26. 7.5.26 VENDOR_SPECIFIC1
      27. 7.5.27 VENDOR_SPECIFIC1_SET
      28. 7.5.28 VENDOR_SPECIFIC1_CLR
      29. 7.5.29 VENDOR_SPECIFIC2
      30. 7.5.30 VENDOR_SPECIFIC2_SET
      31. 7.5.31 VENDOR_SPECIFIC2_CLR
      32. 7.5.32 VENDOR_SPECIFIC1_STS
      33. 7.5.33 VENDOR_SPECIFIC1_LATCH
      34. 7.5.34 VENDOR_SPECIFIC3
      35. 7.5.35 VENDOR_SPECIFIC3_SET
      36. 7.5.36 VENDOR_SPECIFIC3_CLR
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Host or OTG, ULPI Input Clock Mode Application
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Unused Pins Connection
        3. 8.2.1.3 Application Curve
      2. 8.2.2 Device, ULPI Output Clock Mode Application
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
          1. 8.2.2.2.1 Unused Pins Connection
        3. 8.2.2.3 Application Curve
    3. 8.3 External Components
  9. 9 Power Supply Recommendations
    1. 9.1 TUSB1210 Power Supply
    2. 9.2 Ground
    3. 9.3 Power Providers
    4. 9.4 Power Modules
      1. 9.4.1 VDD33 Regulator
      2. 9.4.2 VDD18 Supply
      3. 9.4.3 VDD15 Regulator
    5. 9.5 Power Consumption
  10. 10Layout
    1. 10.1 TUSB121x USB2.0 Product Family Board Layout Recommendations
    2. 10.2 Layout Guidelines
    3. 10.3 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
7.3.1.1.3 ULPI Output Clock Configuration

In this mode, a reference clock must be externally provided on the REFCLK pin. When an input clock is detected on the REFCLK pin, then CLK is automatically changed to an output. For example, 60 MHz ULPI clock is the TUSB1210 devices output on the CLK pin.

Two reference clock input frequencies are supported. REFCLK input frequency is communicated to TUSB1210 through a configuration pin, CFG. See fREFCLK in Table 8-3 for frequency correspondence. TUSB1210 supports square-wave reference clock input only. Reference clock input must be square-wave of amplitude in the range 3 V to 3.6 V. See Section 6.13.