SBAS607B April   2016  – September 2016 ADS127L01

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: Serial Interface
    7. 6.7  Switching Characteristics: Serial Interface Mode
    8. 6.8  Timing Requirements: Frame-Sync Master Mode
    9. 6.9  Switching Characteristics: Frame-Sync Master Mode
    10. 6.10 Timing Requirements: Frame-Sync Slave Mode
    11. 6.11 Switching Characteristics: Frame-Sync Slave Mode
    12. 6.12 Typical Characteristics
  7. 7 Parameter Measurement information
    1. 7.1 Noise Performance
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Analog Inputs (AINP, AINN)
      2. 8.3.2 Digital Filter
        1. 8.3.2.1 Low-Latency Filter
          1. 8.3.2.1.1 Low-Latency Filter Frequency Response
          2. 8.3.2.1.2 Low-Latency Filter Settling Time
        2. 8.3.2.2 Wideband Filter
          1. 8.3.2.2.1 Wideband Filters Frequency Response
          2. 8.3.2.2.2 Wideband Filters Settling Time
      3. 8.3.3 Voltage Reference Inputs (REFP, REFN)
      4. 8.3.4 Clock Input (CLK)
      5. 8.3.5 Out-of-Range-Detect System Monitor
      6. 8.3.6 System Calibration
    4. 8.4 Device Functional Modes
      1. 8.4.1 Operating Modes (HR, LP, VLP)
      2. 8.4.2 Hardware Mode Pins
        1. 8.4.2.1 Interface Selection Pins (FORMAT, FSMODE)
        2. 8.4.2.2 Digital-Filter Path Selection Pins (FILTER[1:0])
        3. 8.4.2.3 Oversampling Ratio Selection Pins (OSR[1:0])
      3. 8.4.3 Start Pin (START)
      4. 8.4.4 Reset and Power-Down Pin (RESET/PWDN)
    5. 8.5 Programming
      1. 8.5.1 Serial Peripheral Interface (SPI) Programming
        1. 8.5.1.1 Chip Select (CS)
        2. 8.5.1.2 Serial Clock (SCLK)
        3. 8.5.1.3 Data Ready (DRDY/FSYNC)
        4. 8.5.1.4 Data Input (DIN)
        5. 8.5.1.5 Data Output (DOUT)
        6. 8.5.1.6 Daisy-Chain Input (DAISYIN)
        7. 8.5.1.7 SPI Timeout
        8. 8.5.1.8 SPI Commands
          1. 8.5.1.8.1 RESET (0000 011x)
          2. 8.5.1.8.2 START (0000 100x)
          3. 8.5.1.8.3 STOP (0000 101x)
          4. 8.5.1.8.4 RDATA (0001 0010)
          5. 8.5.1.8.5 RREG (0010 rrrr 0000 nnnn)
          6. 8.5.1.8.6 WREG (0100 rrrr 0000 nnnn)
      2. 8.5.2 Frame-Sync Programming
        1. 8.5.2.1 Frame-Sync Master Mode
          1. 8.5.2.1.1 Chip Select (CS) in Frame-Sync Master Mode
          2. 8.5.2.1.2 Serial Clock (SCLK) in Frame-Sync Master Mode
          3. 8.5.2.1.3 Frame-Sync (DRDY/FSYNC) in Frame-Sync Master Mode
          4. 8.5.2.1.4 Data Input (DIN) in Frame-Sync Master Mode
          5. 8.5.2.1.5 Data Output (DOUT) in Frame-Sync Master Mode
          6. 8.5.2.1.6 Daisy-Chain Input (DAISYIN) in Frame-Sync Master Mode
        2. 8.5.2.2 Frame-Sync Slave Mode
          1. 8.5.2.2.1 Chip Select (CS) in Frame-Sync Slave Mode
          2. 8.5.2.2.2 Serial Clock (SCLK) in Frame-Sync Slave Mode
          3. 8.5.2.2.3 Frame-Sync (DRDY/FSYNC) in Frame-Sync Slave Mode
          4. 8.5.2.2.4 Data Input (DIN) in Frame-Sync Slave Mode
          5. 8.5.2.2.5 Data Output (DOUT) in Frame-Sync Slave Mode
          6. 8.5.2.2.6 Daisy-Chain Input (DAISYIN) in Frame-Sync Slave Mode
      3. 8.5.3 Data Format
      4. 8.5.4 Status Word
      5. 8.5.5 Cyclic Redundancy Check (CRC)
        1. 8.5.5.1 Computing the CRC
    6. 8.6 Register Maps
      1. 8.6.1 ID: ID Control Register (address = 00h) [reset = x3h]
      2. 8.6.2 CONFIG: ADC Configuration Register (address = 01h) [reset = 00h]
      3. 8.6.3 OFC0: System Offset Calibration Register 0 (address = 02h) [reset = 00h]
      4. 8.6.4 OFC1: System Offset Calibration Register 1 (address = 03h) [reset = 00h]
      5. 8.6.5 OFC2: System Offset Calibration Register 2 (address = 04h) [reset = 00h]
      6. 8.6.6 FSC0: System Gain Calibration Register 0 (address = 05h) [reset = 00h]
      7. 8.6.7 FSC1: System Gain Calibration Register 1 (address = 06h) [reset = 80h]
      8. 8.6.8 MODE: Mode Settings (address = 07h) [reset = xxh]
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Unused Inputs and Outputs
      2. 9.1.2 Multiple Device Configuration
        1. 9.1.2.1 Cascaded Configuration
          1. 9.1.2.1.1 SPI interface Mode
          2. 9.1.2.1.2 Frame-Sync interface Mode
        2. 9.1.2.2 Daisy-Chain Configuration
          1. 9.1.2.2.1 Daisy-Chain Operation Using SPI interface Mode
          2. 9.1.2.2.2 Daisy-Chain Operation Using Frame-Sync interface Mode
        3. 9.1.2.3 Synchronizing Devices
      3. 9.1.3 ADC Input Driver
        1. 9.1.3.1 Antialiasing Filter
        2. 9.1.3.2 Input Driver Selection
        3. 9.1.3.3 Amplifier Stability
      4. 9.1.4 Modulator Saturation
      5. 9.1.5 ADC Reference Driver
        1. 9.1.5.1 Single Chip Solution: REF6xxx
        2. 9.1.5.2 Multichip Solution: REF50xx + OPA320
      6. 9.1.6 Driving LVDD With an External Supply
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Do's and Don'ts
    4. 9.4 Initialization Setup
  10. 10Power Supply Recommendations
    1. 10.1 Power-Supply Sequencing
    2. 10.2 Power-Supply Decoupling
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Community Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

10 Power Supply Recommendations

The ADS127L01 requires either two or three power supplies, depending on if the internal LDO is used to supply the LVDD analog supply. The AVDD analog supply is referenced to AGND, the LVDD analog supply is referenced to AGND, and the DVDD digital supply is referenced to DGND. The analog power supply can only be unipolar (for example, AVDD = 3.0 V, AGND = 0 V) and is independent of the digital power supply. If INTLDO = 0, the LVDD supply is internally generated using the AVDD supply. If INTLDO = 1, the internal LDO is disabled and LVDD supply must be externally supplied. The digital supply sets the digital I/O levels.

10.1 Power-Supply Sequencing

The power supplies can be sequenced in any order, but in no case must any analog or digital inputs exceed the respective analog or digital power-supply voltage limits. Bring the RESET/PWDN pin high after the analog and digital supplies are up, or bring the pin high with the DVDD supply (assuming the AVDD and LVDD supplies come up with or before DVDD). After all supplies are stabilized, wait for the td(POR) timing for the power-on-reset to complete before communicating with the device in order to allow the power-up reset process to complete.

10.2 Power-Supply Decoupling

Good power-supply decoupling is important to achieve optimum performance. AVDD, LVDD, and DVDD must be decoupled with at least a 1-µF capacitor, as shown in Figure 129. Place the bypass capacitors as close to the power-supply pins of the device as possible using low-impedance connections. Use multilayer ceramic chip capacitors (MLCCs) that offer low equivalent series resistance (ESR) and inductance (ESL) characteristics for power-supply decoupling purposes. For very sensitive systems, or for systems in harsh noise environments, avoid the use of vias for connecting the capacitors to the device pins for superior noise immunity. The use of multiple vias in parallel lowers the overall inductance and is beneficial for connections to ground planes. Connect analog and digital ground together as close to the device as possible.

ADS127L01 PS_recommendedcaps_sbas607.gif Figure 129. ADS127L01 Recommended Power-Supply Decoupling