JAJSOX0A March   2024  – June 2024 ADS127L18

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
  7. 6 Parameter Measurement Information
    1. 6.1  Offset Error Measurement
    2. 6.2  Offset Drift Measurement
    3. 6.3  Gain Error Measurement
    4. 6.4  Gain Drift Measurement
    5. 6.5  NMRR Measurement
    6. 6.6  CMRR Measurement
    7. 6.7  PSRR Measurement
    8. 6.8  SNR Measurement
    9. 6.9  INL Error Measurement
    10. 6.10 THD Measurement
    11. 6.11 IMD Measurement
    12. 6.12 SFDR Measurement
    13. 6.13 Noise Performance
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Inputs (AINP, AINN)
        1. 7.3.1.1 Input Range
      2. 7.3.2 Reference Voltage (REFP, REFN)
        1. 7.3.2.1 Reference Voltage Range
      3. 7.3.3 Clock Operation
        1. 7.3.3.1 Internal Oscillator
        2. 7.3.3.2 External Clock
      4. 7.3.4 Power Supplies
        1. 7.3.4.1 AVDD1 and AVSS
        2. 7.3.4.2 AVDD2
        3. 7.3.4.3 IOVDD
        4. 7.3.4.4 Power-On Reset (POR)
        5. 7.3.4.5 CAPA and CAPD
      5. 7.3.5 VCM Output Voltage
      6. 7.3.6 GPIO
      7. 7.3.7 Modulator
      8. 7.3.8 Digital Filter
        1. 7.3.8.1 Wideband Filter
      9. 7.3.9 Low-Latency Filter (Sinc)
        1. 7.3.9.1 Sinc4 Filter
        2. 7.3.9.2 Sinc4 + Sinc1 Cascade Filter
        3. 7.3.9.3 Sinc3 Filter
        4. 7.3.9.4 Sinc3 + Sinc1 Filter
    4. 7.4 Device Functional Modes
      1. 7.4.1  Speed Modes
      2. 7.4.2  Synchronization
        1. 7.4.2.1 Synchronized Control Mode
        2. 7.4.2.2 Start/Stop Control Mode
      3. 7.4.3  Digital Filter Settling
      4. 7.4.4  Conversion-Start Delay Time
      5. 7.4.5  Data Averaging
      6. 7.4.6  Calibration
        1. 7.4.6.1 Offset Calibration Registers
        2. 7.4.6.2 Gain Calibration Registers
        3. 7.4.6.3 Calibration Procedure
      7. 7.4.7  Reset
        1. 7.4.7.1 RESET Pin
        2. 7.4.7.2 Reset by SPI Register
        3. 7.4.7.3 Reset by SPI Input Pattern
      8. 7.4.8  Power-Down
      9. 7.4.9  Idle and Standby Modes
      10. 7.4.10 Diagnostics
        1. 7.4.10.1 ERROR Pin and ERR_FLAG Bit
        2. 7.4.10.2 Clock Counter
        3. 7.4.10.3 SCLK Counter
        4. 7.4.10.4 Frame-Sync CRC
        5. 7.4.10.5 SPI CRC
        6. 7.4.10.6 Register Map CRC
        7. 7.4.10.7 Self Test
      11. 7.4.11 Frame-Sync Data Port
        1. 7.4.11.1 FSYNC Pin
        2. 7.4.11.2 DCLK Pin
        3. 7.4.11.3 DOUT Pins
        4. 7.4.11.4 DIN Pins
        5. 7.4.11.5 Time Division Multiplexing
        6. 7.4.11.6 Daisy Chain
        7. 7.4.11.7 Data Packet
        8. 7.4.11.8 STATUS_DP Header
        9. 7.4.11.9 Data Port Timing Adjustment
    5. 7.5 Programming
      1. 7.5.1 Hardware Programming
      2. 7.5.2 SPI Programming
        1. 7.5.2.1 Chip Select (CS)
        2. 7.5.2.2 Serial Clock (SCLK)
        3. 7.5.2.3 Serial Data Input (SDI)
        4. 7.5.2.4 Serial Data Output (SDO)
      3. 7.5.3 SPI Frame
      4. 7.5.4 SPI Commands
        1. 7.5.4.1 Read Register Command
        2. 7.5.4.2 Write Register Command
      5. 7.5.5 SPI Daisy-Chain
  9. 8 Register Map
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Input Driver
      2. 9.1.2 Antialias Filter
      3. 9.1.3 Reference Voltage
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 静電気放電に関する注意事項
    6. 10.6 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Mechanical Data

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6.3 Gain Error Measurement

Gain error is defined as the difference between the actual and the ideal slopes of the ADC transfer function. Gain error is measured by applying dc test voltages at –95% and 95% of FSR. The error is calculated by subtracting the difference of the dc test voltages (ideal slope) from the difference in the ADC output voltages (actual slope). The difference in the slopes is divided by the ideal slope and multiplied by 106 to convert the error to ppm of FSR. Errors resulting from the ADC reference voltage are excluded from the gain error measurement. The gain error is specified at TA = 25°C. Equation 12 shows the calculation of gain error:

Equation 2. Gain Error (ppm of FSR) = 106 · (ΔVOUT – ΔVIN) / ΔVIN

where:

  • ΔVOUT = Difference of two ADC output voltages
  • ΔVIN = Difference of two input test voltages