JAJSOX0A March   2024  – June 2024 ADS127L18

ADVANCE INFORMATION  

  1.   1
  2. 特長
  3. アプリケーション
  4. 概要
  5. Pin Configuration and Functions
  6. Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
  7. Parameter Measurement Information
    1. 6.1  Offset Error Measurement
    2. 6.2  Offset Drift Measurement
    3. 6.3  Gain Error Measurement
    4. 6.4  Gain Drift Measurement
    5. 6.5  NMRR Measurement
    6. 6.6  CMRR Measurement
    7. 6.7  PSRR Measurement
    8. 6.8  SNR Measurement
    9. 6.9  INL Error Measurement
    10. 6.10 THD Measurement
    11. 6.11 IMD Measurement
    12. 6.12 SFDR Measurement
    13. 6.13 Noise Performance
  8. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Inputs (AINP, AINN)
        1. 7.3.1.1 Input Range
      2. 7.3.2 Reference Voltage (REFP, REFN)
        1. 7.3.2.1 Reference Voltage Range
      3. 7.3.3 Clock Operation
        1. 7.3.3.1 Internal Oscillator
        2. 7.3.3.2 External Clock
      4. 7.3.4 Power Supplies
        1. 7.3.4.1 AVDD1 and AVSS
        2. 7.3.4.2 AVDD2
        3. 7.3.4.3 IOVDD
        4. 7.3.4.4 Power-On Reset (POR)
        5. 7.3.4.5 CAPA and CAPD
      5. 7.3.5 VCM Output Voltage
      6. 7.3.6 GPIO
      7. 7.3.7 Modulator
      8. 7.3.8 Digital Filter
        1. 7.3.8.1 Wideband Filter
      9. 7.3.9 Low-Latency Filter (Sinc)
        1. 7.3.9.1 Sinc4 Filter
        2. 7.3.9.2 Sinc4 + Sinc1 Cascade Filter
        3. 7.3.9.3 Sinc3 Filter
        4. 7.3.9.4 Sinc3 + Sinc1 Filter
    4. 7.4 Device Functional Modes
      1. 7.4.1  Speed Modes
      2. 7.4.2  Synchronization
        1. 7.4.2.1 Synchronized Control Mode
        2. 7.4.2.2 Start/Stop Control Mode
      3. 7.4.3  Digital Filter Settling
      4. 7.4.4  Conversion-Start Delay Time
      5. 7.4.5  Data Averaging
      6. 7.4.6  Calibration
        1. 7.4.6.1 Offset Calibration Registers
        2. 7.4.6.2 Gain Calibration Registers
        3. 7.4.6.3 Calibration Procedure
      7. 7.4.7  Reset
        1. 7.4.7.1 RESET Pin
        2. 7.4.7.2 Reset by SPI Register
        3. 7.4.7.3 Reset by SPI Input Pattern
      8. 7.4.8  Power-Down
      9. 7.4.9  Idle and Standby Modes
      10. 7.4.10 Diagnostics
        1. 7.4.10.1 ERROR Pin and ERR_FLAG Bit
        2. 7.4.10.2 Clock Counter
        3. 7.4.10.3 SCLK Counter
        4. 7.4.10.4 Frame-Sync CRC
        5. 7.4.10.5 SPI CRC
        6. 7.4.10.6 Register Map CRC
        7. 7.4.10.7 Self Test
      11. 7.4.11 Frame-Sync Data Port
        1. 7.4.11.1 FSYNC Pin
        2. 7.4.11.2 DCLK Pin
        3. 7.4.11.3 DOUT Pins
        4. 7.4.11.4 DIN Pins
        5. 7.4.11.5 Time Division Multiplexing
        6. 7.4.11.6 Daisy Chain
        7. 7.4.11.7 Data Packet
        8. 7.4.11.8 STATUS_DP Header
        9. 7.4.11.9 Data Port Timing Adjustment
    5. 7.5 Programming
      1. 7.5.1 Hardware Programming
      2. 7.5.2 SPI Programming
        1. 7.5.2.1 Chip Select (CS)
        2. 7.5.2.2 Serial Clock (SCLK)
        3. 7.5.2.3 Serial Data Input (SDI)
        4. 7.5.2.4 Serial Data Output (SDO)
      3. 7.5.3 SPI Frame
      4. 7.5.4 SPI Commands
        1. 7.5.4.1 Read Register Command
        2. 7.5.4.2 Write Register Command
      5. 7.5.5 SPI Daisy-Chain
  9. Register Map
  10. Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Input Driver
      2. 9.1.2 Antialias Filter
      3. 9.1.3 Reference Voltage
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 静電気放電に関する注意事項
    6. 10.6 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Mechanical Data

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Recommended Operating Conditions

over operating ambient temperature range (unless otherwise noted)
MIN NOM MAX UNIT
POWER SUPPLY
Analog power supply AVDD1 to AVSS Max-speed mode 4.5 5.5 V
High-speed mode 4.5 5.5
Mid-speed mode 3 5.5
Low-speed mode 2.85 5.5
AVDD1 to DGND 1.65 V
AVSS / AVDD1 ratio 1.2 V/V
AVDD2 to AVSS 1.74 5.5 V
AVSS to DGND –2.75 0
Digital power supply IOVDD to DGND 1.65 1.95 V
ANALOG INPUTS
VAINP,
VAINN
Absolute input voltage Input buffer off AVSS – 0.05 AVDD1 + 0.05 V
Input buffer on AVSS + 0.1 AVDD1 – 0.1
VIN Differential input voltage
VIN = VAINP – VAINN
1x input range –VREF VREF V
2x input range –2∙VREF 2∙VREF
VOLTAGE REFERENCE INPUTS
VREF Differential reference voltage
VREF = VREFP – VREFN
Low-reference range 0.5 2.5 2.75 V
High-reference range 1 4.096 AVDD1 – AVSS
VREFN Negative reference voltage AVSS – 0.05 V
VREFP Positive reference voltage REFP buffer off AVDD1 + 0.05 V
REFP buffer on AVDD1 – 0.7
CLOCK INPUT
fCLK Clock frequency Max-speed mode 0.5 32.768 33.6 MHz
High-speed mode 0.5 25.6 26.2
Mid-speed mode 0.5 12.8 13.1
Low-speed mode 0.5 3.2 3.28
DIGITAL INPUTS
VIL Logic low input voltage 0 0.3∙IOVDD V
VIH Logic high input voltage 0.7∙IOVDD IOVDD V
ILEAK External leakage current Tri-state pins, floating input state –5 5 µA
CLOAD Capacitive load Tri-state pins, floating input state 50 pF
REXT Pull-up or pull-down resistance Tri-state pins, logic low or high state 0 3 kΩ
TEMPERATURE RANGE
TA Ambient temperature Operational –50 125 °C
Specification –40 125